Just one small observation about your logic regarding the soldering of random legs of the IC. Your logic and technical aspect is fine but all these mass produced cards are usually, Wave Soldered in the factory, which means all the legs of the IC are soldered at one go. From what I know, standard quality electronic components are designed to withstand this heat, without getting damaged. Otherwise, your videos are very informative and useful. Thank you.
absolutely perfect dear at factory the soldering temperature and soldering time are predefined and set properly, either for manual soldering or automatic soldering but in the field there is no temperature controlled seldering iron and not too expert soldering person even in my department my subordinate engineers and technicians most of time damage ics by unconcontrolled temperature soldering iron and soldering time, and in line soldering so in my experience it is best idea to solder or desolder randomly
Hi Sir, thank you for sharing your knowledge and skills about electronics troubleshooting and repairing, many people who are interested in electronics like me have learned from your videos. I learned a lot from your tutorial videos. In fact I really understood very well how a SMPS woks. Keep up the good work and looking forward to the next tutorial video. More power to you sir. Mabuhay....
Great video! The old IC you pulled out looked counterfeit. The shape of Texas was more fat and round and the "I" was not clear. The new one that you installed had a definite clear shape of Texas with a definitive letter "I". Thanks for sharing sir!
best regards most of time the ics have logos but these are not real as most of the components are being manufactured in china, so brand and quality cannot be certified just part number is printed
Nice to meet you, my name is NEKO🐱TAROU, a Japanese RUclipsr. I have the same PSU as you. When it breaks down, I will watch your video and try to fix it. Thank you for sharing the video. 👍 I subscribed to your channel. ❗
most welcome try to troubleshoot and if you find some difficulty. please let me know. i will try my best to sort out the problem wishing you best of luck and success
I did enjoy the video. I like how you start off with a careful visual inspection of the components and then zero in on the likely culprits. A very satisfying repair.
Sir, perfect working in all respects.more over cleaning, very best, and checked each and every transistor, ic , capacitor etc,super job done.thorurouly repaired sir, the best, good 👍
My dear Brother, I am now only 68yrs! Electronics is my hobby and for passing my liesure period! I fond of watching yours knowledgeable and informative videos like this in You Tube ! May.i expect a little but important help from you? I tried to make a transformer less circuit for 12volt to run a cooling fan (3"12v) with that ? But I have failed! Out put is coming 13.2volt DC ? But while I connect to load the volt shows 4.3 or less! resulting fan is moving very slow! I can't understand what is fault are there ! May be for low ampere or any other reason? I wd like to let you know there are no sufficient room to fix the SD transformer. Kindly help me to give a fruitful suggestion in this regard? I shall be highly grateful to you. My heartiest good wishes for all of your upcoming videos as well as your present video. Stay happy and good bye for the day. I will be awaiting for your reply.
Good afternoon sir. when you are using 3" 12V fan, it means it is DC fan. it needs more ameres and the transformerless power supply (volatge dropper circuit) can provide just in milliampers, that is causing to drop the volatge to 4.3 volt. it is better to use isolated transfomre based power supply having a safe limit for current capacity please accept my best regards
Hello sir , I love to watch and relearn from your vdos , your tip to desolder ICs in random order reminded me of my service instructor who use to reiterate the same thing and i used to repeat to my students .... Best regards
Hi i love every single video you have produced. Always learn something new. But i am missing something is it possible you can show us how to verify and check components like the rectifiers, small round capacitors, and transistors in and out of circuit. maybe resistors as well.And show us what a good reading should be and what is a bad reading is thanks.
Hello Mr Haseeb, my youtube teacher. I can watch your videos for hours and not tire, I have a question for you. Do you have a video that can teach us your youtube students how to follow traces from point to point from the various components on a PCB on different types of electronics, or can you make a video for us please, I am trying to learn but I get lost looking at all the lines and most times it is a bit frustrating for a beginner like me because I really want to understand where these traces from each component begin and end and I get lost, thank you teacher for being so professional in the way you teach us!
Very Interesting ,,,,,,, Good Teacher......Easy to understand.........Dear Sir ....What is best Bulb wattage for use series to power up MPCS to check....I mean 100w or 40W
I want to use smps for my garden lighting supply instead of AC for safety reasons. Will it be a good idea? I will run many 12v DC led bulbs. Also please tell why SMPS have many output connections? Should I club all connections into 1 set of 12v DC? Also please tell is there any chance that a SMPS gives AC output and give shock to anyone in the garden? If there is a chance, what to do? Should I use a fuse to avoid any mis-happening or is there any other method such as MCB? If yes, what should be the specifications of the fuse/mcb or other component?
Haseeb, excellent video with great advice on how to desolder IC's. I was wondering why you needed to take the heat sinks off to do the testing??? Is there a way to test the transistors without desoldering them?
Thank you for your video. I looked up the TL494 IC chip. I realized that I did not understand it's operation. Is it possible to trouble shoot a circuit like a power supply without totally understanding the operation of the circuit, but able to understand the basics of the circuit operation. For example, I know that the TL494 is the regulator IC. The crack on the TL494 would make you suspect that it is bad. I understand SMPS basics, but I don't totally understand the circuit operation. So, I consider this a learning challenge to understand how all of this works. If someone wanted me to fix a power supply. I probably would spend more time trying to understand how the circuit works than actually spending time on trouble shooting the circuit. Could you suggest any books or material that goes into the circuit operation of power supplies. Thank you again.
I really appreciate your very detailed and accurate explanation. Many thanks dear . Can we check the vcc voltage without the ic ( before replacing the new ic) pls ?
Hi Sir. Another excellent repair. Is there any reason for the soldering sequence of the IC? Is it better to solder pins opposite than side by side for overheating? Kind regards, Frederic.
it is best way to divide ic pins in four portions for example i have 16 pin ic first i will solder pin 1, then 5, then 9 and 13 then 2, 6, 10 & 14 then 3, 7, 10 & 15 at ast 4, 8, 12 & 16 so using this technique every last pin will get adequate cooling time
Was a wear problem of tl494 Because it was oscillating and you got some dc voltages on output. Also you got voltage near 5 volt in 5 volt referance pin So If that crack was not exsist the ic would be the last component you suspect to damage
no it was TL494 failure initial low voltage are being provided from start up circuit, it is composed of using mosfet gate biasing circuit + pulse transformer secondary side. this start up circuit, operates the mosfets in conduction state, which cause a limited current in mosfets and the transformer, in result the limited current causes to produce low voltage, and also it provides vcc voltage to SMPS controller, and it can start IC, then ic will start to produce rated output and it starts voltage regulation
Sir my question is that why in 12v 20amp or 40 amp smps power supply such type of design i mean push pull system is used why not uc 3842 or 43 is used which simple design and efficient too as used in inverter charger circuits. Thanks for reply
Thank you Haseeb for the great explanation as usual, how can i get the soldering iron tool like yours in this video? and also how can i get the schematic diagram for any smps?
Hello After repairing this type, I noticed that there was a voltage value on the body of the charger that reached 100 volts, when placing the avometer sensors between one of the electrical inputs and the body of the charger. Is there any clarification because I noticed this using my initial electric screwdriver, which gave strong lighting Note dear sir The board and all elements are completely isolated, the sequence lamp does not work, and the device works well after replacing the 13007 transistors
I have a quick question. Is that pull the required ampere output such as 20A or 30A or 40A from 230v with a 6A/10A 3 pin? I am using a car amplifier at home which is maximum ampere rated as 35. To get a desired ampere output what should I do?
wow great question I have fluke 179 fluke 115 fluke 77iii aneng Q1 uni-t ut202a+ and tenma but I prefer aneng Q1 as it is cheaper, and better response and accurate results so It attracts me. otherwise there is nothing special behind it's usage
if we compare datasheets viper22a and AM22A have same switching frequency of 60KHz the difference is in VCC voltages. i think AM22A will not work properly in place of viper22a. as i never did it practically, so i cannot some authentic words
@@HaseebElectronics Thank you, dear brother. Is this diagram for this particular model, or is there a difference because I will rely on it to read the resistor numbers and replace them with the same value?
What did the IC fail ?. The Ic seemed to be cracked and there was discolouration near one pin . This suggested the IC suffered some catastrophic event causing the failure . But no other fault was found , which leaves the question what caused the catastrophic failure of the IC ?
material failure is possible in electronics. as its seems that its reference regulator circuit got problem which caused to chip substrate damage. it is also strange for me that vcc section is normal, and output side of refrence circuit is good as these 5 vlt reference are being used for chip biasing, internal flip-flops, comparators biasing, any internal failure may be a reason of its failure
Hello Sir! I have a question, how can I change the 5v charger to 12v? If you have time, answer me or show us please!. I saw a video made on RUclips but I don't know the language, it's mostly indie!
Hi Mr.Haseeb, my 120W (12v 10A) smps output voltage good but output current very low, i am unable to use 12v 5A load even in smps no voltage fluctuation or down very stable voltage, i checked all components are good in pcb, but low output current, so what is problem & what component to be replace in smps ? waiting your reply
no, it don't have short circuit protection. these ics have current limit option only, because it is using TL494/KA7500, and this ic utilize error amplifier number 2 to limit the current,
Very good teaching Sir ek Tdk sws 75-24 power supply k out put ma 24 k bajay 5v atay hain aur VR no effect and voltage decreases gradually 24 to 5v kindly what is the fault please
i have a ac/dc power supply and it stopt working .its 12 volt 8 amp.but now there is onley 4,5 volt output .the ic is black with no markings on it .the ic is an 8 pin part .i dit the same as you dit and the ic is fault .how to replace this coponent
I think it is material failure if it was damaged due to related components then we can say it was due to external cause but in this situation I think it's reference regulator (inside Ic) is damaged
It's very simple, VR1 voltage regulator trimmer 1 kohm is defective, try to 300 Ohm - 560 Ohm resistor. If I have made a shorcut for trimmer voltage became 13,5 V the output.
Selâmün Aleyküm Çok güzel ,bazı videolarından istifade ettim, Teşekkür ederim. Senin yaptığın bu işleri Türkçe konuşan biri yapsa daha çok şey öğrenebilirdim. Maalesef ben Türkçe dışında başka bir dil de bilmiyorum. Alt yazı seçeneği ile değerlendirip biraz daha anlamaya çalışıyorum.
Hello sir asalawalekum bhai jaan ..mere pass ek cstmr ka 12 volt 30 ampere smps aaya mene usko cheak kiya d13009k mosfet open the wo change kiye uske baad drive volt pr c1815 trasister change kiye 2.2 ohm drive signle resistance change ki ur uske baad supply ok ho gyi 12 volt output b de raha h ur chal b raha h pr samasya ye hai k jaise hi uske upr load dala jata h to thodi der chalne k baad uske d13009 mosfet burn ho rhe h ur ye 3 baar ho chuka h teeno baar mene mosfet chnge kiye har cheez baari baari cheak ki pr problum smj nai aayi plzz meri help kare esa ku ho raha h sir
Peace be upon you. I have the same power supply, but it makes a buzzing sound and the output voltage is 16. There is no control over the variable resistor, and when loaded, the voltage drops. What is the reason?
![Megan Thee Stallion - Roc Steady (feat. Flo Milli) [Official Video]](http://i.ytimg.com/vi/HozPPyqW0dY/mqdefault.jpg)
good repair 👍👏👋
best regards dear friend
Just one small observation about your logic regarding the soldering of random legs of the IC. Your logic and technical aspect is fine but all these mass produced cards are usually, Wave Soldered in the factory, which means all the legs of the IC are soldered at one go. From what I know, standard quality electronic components are designed to withstand this heat, without getting damaged. Otherwise, your videos are very informative and useful. Thank you.
absolutely perfect dear
at factory the soldering temperature and soldering time are predefined and set properly, either for manual soldering or automatic soldering
but in the field there is no temperature controlled seldering iron and not too expert soldering person
even in my department my subordinate engineers and technicians most of time damage ics by unconcontrolled temperature soldering iron and soldering time, and in line soldering
so in my experience it is best idea to solder or desolder randomly
please accept my best regards and special thanks for your kind observation
Hi Sir, thank you for sharing your knowledge and skills about electronics troubleshooting and repairing, many people who are interested in electronics like me have learned from your videos. I learned a lot from your tutorial videos. In fact I really understood very well how a SMPS woks. Keep up the good work and looking forward to the next tutorial video. More power to you sir. Mabuhay....
Great video! The old IC you pulled out looked counterfeit. The shape of Texas was more fat and round and the "I" was not clear. The new one that you installed had a definite clear shape of Texas with a definitive letter "I". Thanks for sharing sir!
best regards
most of time the ics have logos but these are not real
as most of the components are being manufactured in china, so brand and quality cannot be certified
just part number is printed
Nice to meet you, my name is NEKO🐱TAROU, a Japanese RUclipsr. I have the same PSU as you. When it breaks down, I will watch your video and try to fix it. Thank you for sharing the video. 👍
I subscribed to your channel. ❗
most welcome
try to troubleshoot and if you find some difficulty. please let me know. i will try my best to sort out the problem
wishing you best of luck and success
I did enjoy the video. I like how you start off with a careful visual inspection of the components and then zero in on the likely culprits. A very satisfying repair.
Gday great presentation. Liked how you made sure other components were in good shape before replacing the IC. I always learn something from you.
best regards and special thanks
You explain things so good. And you are good at what you do. Thank you for taking time and making this video. Tbark Allah 3alik.
thanks a lot
stay blessed
Sir, perfect working in all respects.more over cleaning, very best, and checked each and every transistor, ic , capacitor etc,super job done.thorurouly repaired sir, the best, good 👍
best regards
My dear Brother, I am now only 68yrs! Electronics is my hobby and for passing my liesure period! I fond of watching yours knowledgeable and informative videos like this in You Tube ! May.i expect a little but important help from you? I tried to make a transformer less circuit for 12volt to run a cooling fan (3"12v) with that ? But I have failed! Out put is coming 13.2volt DC ? But while I connect to load the volt shows 4.3 or less! resulting fan is moving very slow! I can't understand what is fault are there ! May be for low ampere or any other reason? I wd like to let you know there are no sufficient room to fix the SD transformer. Kindly help me to give a fruitful suggestion in this regard? I shall be highly grateful to you. My heartiest good wishes for all of your upcoming videos as well as your present video. Stay happy and good bye for the day. I will be awaiting for your reply.
Good afternoon sir.
when you are using 3" 12V fan, it means it is DC fan. it needs more ameres and the transformerless power supply (volatge dropper circuit) can provide just in milliampers, that is causing to drop the volatge to 4.3 volt.
it is better to use isolated transfomre based power supply having a safe limit for current capacity
please accept my best regards
Thank you !!! Best wishes from Brazil 👏👏
best regards 💕
I love watching your tutorial
video, very helpful. Explanation is very clear. Thank you Sir!
most welcome and special thanks
You da man, keep the videos coming. Very educational
Hello sir , I love to watch and relearn from your vdos , your tip to desolder ICs in random order reminded me of my service instructor who use to reiterate the same thing and i used to repeat to my students .... Best regards
Wonderful video dear friend, have a happy Thursday ☺️
best regards and stay blessed
Thank you !!! Best wishes from Turkey
most welcome
Hi i love every single video you have produced. Always learn something new. But i am missing something is it possible you can show us how to verify and check components like the rectifiers, small round capacitors, and transistors in and out of circuit. maybe resistors as well.And show us what a good reading should be and what is a bad reading is thanks.
Hello Mr Haseeb, my youtube teacher. I can watch your videos for hours and not tire, I have a question for you. Do you have a video that can teach us your youtube students how to follow traces from point to point from the various components on a PCB on different types of electronics, or can you make a video for us please, I am trying to learn but I get lost looking at all the lines and most times it is a bit frustrating for a beginner like me because I really want to understand where these traces from each component begin and end and I get lost, thank you teacher for being so professional in the way you teach us!
Very Interesting ,,,,,,, Good Teacher......Easy to understand.........Dear Sir ....What is best Bulb wattage for use series to power up MPCS to check....I mean 100w or 40W
best regards
50watt tungsten lamp is awesome for power supplies upto 100 watt.
60/100 watt lamp will good for 100-200 watt power supplies
I want to use smps for my garden lighting supply instead of AC for safety reasons. Will it be a good idea? I will run many 12v DC led bulbs.
Also please tell why SMPS have many output connections? Should I club all connections into 1 set of 12v DC?
Also please tell is there any chance that a SMPS gives AC output and give shock to anyone in the garden?
If there is a chance, what to do? Should I use a fuse to avoid any mis-happening or is there any other method such as MCB?
If yes, what should be the specifications of the fuse/mcb or other component?
Woow before you disassemble it i was thinking that the feedback is in problem thank you
yes brother
everyday we have to learn something new
Haseeb, excellent video with great advice on how to desolder IC's. I was wondering why you needed to take the heat sinks off to do the testing??? Is there a way to test the transistors without desoldering them?
Not that is reliable.
Saludos desde Venezuela excelente video muy buena su explicación
Saludos. Buenos días y un agradecimiento especial por sus valiosas palabras.
Great! What liquid do you use to clean the board with the toothbrush? Thanks
it is
technical alcohol
isopropyl alcohol
or methylated spirit
تشکر وسپاس جناب مهندس ممنون وهزاران لایک.....لطفا وحتما راجعب پمپ...و.. وکیوم وهویه مکنده لحیم
وات ان توضیح دهید ممنونم..🙏🙏👌👌❤❤
Very good video. How warm are your soldering irons in this video?
i use soldering iron at 380-410 degree centigrade
desoldering tool 420-440 degree centigrade
Very good and useful information sir thanks for sharing this knowledge to us
it is my pleasure
Very nicely explained and demonstrated
best regards and special thanks
I watched most of ur videos .. ur explanation is amazing .. I wish you were my teacher at the University 😁
best regards and special thanks
Thank you very much for your knowledge sharing
Thank you for your video. I looked up the TL494 IC chip. I realized that I did not understand it's operation. Is it possible to trouble shoot a circuit like a power supply without totally understanding the operation of the circuit, but able to understand the basics of the circuit operation. For example, I know that the TL494 is the regulator IC. The crack on the TL494 would make you suspect that it is bad. I understand SMPS basics, but I don't totally understand the circuit operation. So, I consider this a learning challenge to understand how all of this works. If someone wanted me to fix a power supply. I probably would spend more time trying to understand how the circuit works than actually spending time on trouble shooting the circuit. Could you suggest any books or material that goes into the circuit operation of power supplies. Thank you again.
Also do we get equal base bias voltage to the main 2 transistors in the start up section when there is no load ? pls clarify . Thanks
I really appreciate your very detailed and accurate explanation. Many thanks dear .
Can we check the vcc voltage without the ic ( before replacing the new ic) pls ?
really enjoyed sir soldering/desoldering technique is useful
best regards and special thanks
Sir, thank you for the IC soldering sequence tip.
it is my pleasure
Hi Sir. Another excellent repair. Is there any reason for the soldering sequence of the IC? Is it better to solder pins opposite than side by side for overheating? Kind regards, Frederic.
it is best way to divide ic pins in four portions
for example i have 16 pin ic
first i will solder pin 1, then 5, then 9 and 13
then 2, 6, 10 & 14
then 3, 7, 10 & 15
at ast 4, 8, 12 & 16
so using this technique every last pin will get adequate cooling time
Hi sir...namaskaar.
I like your working style.
Which liquid is using to clean the pcb..?
Thank you for the video. Good night 🙏
best regards and special thanks
it is isopropyl alcohol
technical alcohol or methylated spirit
@@HaseebElectronics Thank you for your reply 🙏
Was a wear problem of tl494
Because it was oscillating and you got some dc voltages on output.
Also you got voltage near 5 volt in 5 volt referance pin
So If that crack was not exsist the ic would be the last component you suspect to damage
no
it was TL494 failure
initial low voltage are being provided from start up circuit, it is composed of using mosfet gate biasing circuit + pulse transformer secondary side.
this start up circuit, operates the mosfets in conduction state, which cause a limited current in mosfets and the transformer, in result the limited current causes to produce low voltage, and also it provides vcc voltage to SMPS controller, and it can start IC, then ic will start to produce rated output and it starts voltage regulation
Sir my question is that why in 12v 20amp or 40 amp smps power supply such type of design i mean push pull system is used why not uc 3842 or 43 is used which simple design and efficient too as used in inverter charger circuits. Thanks for reply
I have a power supply 27 V 10 A..output voltage is drop only 4 V,but after a few minutes output voltage is normal.what of cause it? Thank you..
Thank you Haseeb for the great explanation as usual, how can i get the soldering iron tool like yours in this video? and also how can i get the schematic diagram for any smps?
best regards
it is WELLER WR3M made in Germany, you can purchase it online
drive.google.com/file/d/1_gw2TujAWDSzaWYBIpBEOreGime8hKCv/view?usp=share_link
drive.google.com/drive/folders/1TlHNmTDtY2NvDAg1XQUkMQFXhpG3aLuV?usp=share_link
Hello
After repairing this type, I noticed that there was a voltage value on the body of the charger that reached 100 volts, when placing the avometer sensors between one of the electrical inputs and the body of the charger.
Is there any clarification because I noticed this using my initial electric screwdriver, which gave strong lighting
Note dear sir
The board and all elements are completely isolated, the sequence lamp does not work, and the device works well after replacing the 13007 transistors
please check this video and reply the results
ruclips.net/video/6c7XCBITZDo/видео.html
Hi sir. Thanks for the videos.
I don't understand how a bad ic tl494 can have its vcc input lowered. I thought the vcc will not affected.
best regards
i think its internal regulator is damaged, which caused to pull down the vcc pin. so ic cannot start working
@@HaseebElectronics thank you very much.
great tip on soldering IC's
it is my pleasure
hi bro salaam, what are the components to buy for starting psu repair
Very helpful video. Thanks for this video sir jee
best regards and special thanks
I really enjoy your videos. Thank you.
So nice of you
amazing my favorite teacher.
best regards
Very informative thank u so much👌🏼
it is my pleasure
I have a quick question. Is that pull the required ampere output such as 20A or 30A or 40A from 230v with a 6A/10A 3 pin? I am using a car amplifier at home which is maximum ampere rated as 35. To get a desired ampere output what should I do?
Do we use of a IC socket for the TL494 ?
Salaam Bhai Sahib
wa alaikum salaam bhai Ji
very interesting haseeb thankyou
Very nice repair video !!
best regards and special thanks
what makes you choose aneng Q1 multimeter instead of the fluke you used previously?
wow great question
I have fluke 179
fluke 115
fluke 77iii
aneng Q1
uni-t ut202a+
and tenma
but I prefer aneng Q1 as it is cheaper, and better response and accurate results
so It attracts me. otherwise there is nothing special behind it's usage
Another excellent repair
it is my pleasure
thanks master!
may i ask if AM22a can be replaced by Viper22a?
if we compare datasheets
viper22a and AM22A have same switching frequency of 60KHz
the difference is in VCC voltages. i think AM22A will not work properly in place of viper22a.
as i never did it practically, so i cannot some authentic words
@@HaseebElectronics thanks for ur effort to verify my modification
Thank you, i have a very similar SMPS but instead of TL494 it has KA7500BD, but i had the same voltage and the same problem. Thanks!
Hi sir which mosfet are used in the smps for ic tl494
Hi Haseeb
Can you make a video on the functions of an led/lcd tv t-icon board and how it function.
Thanks on advance
Thank you my friend, do you have a diagram for this type of power source, because I need some resistor values
kindly check this diagram. might be it may help bit.ly/3y9RJ4g
@@HaseebElectronics Thank you, dear brother. Is this diagram for this particular model, or is there a difference because I will rely on it to read the resistor numbers and replace them with the same value?
What did the IC fail ?. The Ic seemed to be cracked and there was discolouration near one pin . This suggested the IC suffered some catastrophic event causing the failure . But no other fault was found , which leaves the question what caused the catastrophic failure of the IC ?
material failure is possible in electronics. as its seems that its reference regulator circuit got problem which caused to chip substrate damage. it is also strange for me that vcc section is normal, and output side of refrence circuit is good
as these 5 vlt reference are being used for chip biasing, internal flip-flops, comparators biasing,
any internal failure may be a reason of its failure
Beautiful Video Big Thumbs Up # 532
best regards and special thanks
dear i am watch your video nicely explanation please let me know how aux supply of Control IC is getting
اشكرك
Hello Sir! I have a question, how can I change the 5v charger to 12v? If you have time, answer me or show us please!. I saw a video made on RUclips but I don't know the language, it's mostly indie!
Is there any video for dual output.. Like 24 0 12v
Guruji very nicely explained
💯❤️❤️❤️❤️🙏🙏🙏🙏
best regards 💕
Hi Mr.Haseeb,
my 120W (12v 10A) smps output voltage good but output current very low, i am unable to use 12v 5A load even in smps no voltage fluctuation or down very stable voltage, i checked all components are good in pcb, but low output current, so what is problem & what component to be replace in smps ? waiting your reply
Informative vedeo thank u so much.
it is my pleasure
I have the same problem, but mine is a computer power supply. thank you for the tricks given, maybe I also need to replace the pwm IC.
Jazakallahu khairan Bhai 🙏
best regards
Good
Can you please explain how current control works ?
You are good.would like you to so sort out more on inverter problems.
Do these supplies have short circuit protection?
no, it don't have short circuit protection.
these ics have current limit option only, because it is using TL494/KA7500, and this ic utilize error amplifier number 2 to limit the current,
@@HaseebElectronics so this is what happened in my font. The pointers came together. Thank you for your attention. Good job.
Good job.....thanks 👍
best regards 💕
Very good teaching
Sir ek Tdk sws 75-24 power supply k out put ma 24 k bajay 5v atay hain aur VR no effect and voltage decreases gradually 24 to 5v kindly what is the fault please
Thanks.you explain very good.
Vary very nice video sir
thanks a lot brother
Sir aap kay pas jo desoldering device hay kidhr say melega
ye Weller wr3m rework station he
Amazon se online purchase kr saktey hein
i have a ac/dc power supply and it stopt working .its 12 volt 8 amp.but now there is onley 4,5 volt output .the ic is black with no markings on it .the ic is an 8 pin part .i dit the same as you dit and the ic is fault .how to replace this coponent
Good day sir , please can you do a video on how to calculate the output inductor of power supply using tl494 please.
The IC was damaged was this a random device failure or was there some operating condition that caused damage to the IC ?
I think it is material failure
if it was damaged due to related components then we can say it was due to external cause
but in this situation I think it's reference regulator (inside Ic) is damaged
hi sir can we identify the output voltage of smps by the output capacitor for example 1000uf/35 it is possible 24 volts output?
Well done again 👍
Very nice, 🌹thanks
Welcome 😊
Sir plz china battery charger ki ic yx009 ki jagha konsi ic replace ki jai take charger banane may asani ho plz rahnomai kare
جزاك الله خير
االله يسلمك و يسعدك
Very good sir
it is my pleasure
It's very simple, VR1 voltage regulator trimmer 1 kohm is defective, try to 300 Ohm - 560 Ohm resistor. If I have made a shorcut for trimmer voltage became 13,5 V the output.
Hello 👍👍 thanks you, good man
best regards
Selâmün Aleyküm
Çok güzel ,bazı videolarından istifade ettim, Teşekkür ederim. Senin yaptığın bu işleri Türkçe konuşan biri yapsa daha çok şey öğrenebilirdim. Maalesef ben Türkçe dışında başka bir dil de bilmiyorum. Alt yazı seçeneği ile değerlendirip biraz daha anlamaya çalışıyorum.
Thanks a lot........👏👍
best regards and special thanks
Nice video Sir
Where is this smps used?
it is used in decoration lighting system
@@HaseebElectronics ok Sir
Thank you so much
Hvala za prijevod
zadovoljstvo mi je. ugodan dan
Hello sir asalawalekum bhai jaan ..mere pass ek cstmr ka 12 volt 30 ampere smps aaya mene usko cheak kiya d13009k mosfet open the wo change kiye uske baad drive volt pr c1815 trasister change kiye 2.2 ohm drive signle resistance change ki ur uske baad supply ok ho gyi 12 volt output b de raha h ur chal b raha h pr samasya ye hai k jaise hi uske upr load dala jata h to thodi der chalne k baad uske d13009 mosfet burn ho rhe h ur ye 3 baar ho chuka h teeno baar mene mosfet chnge kiye har cheez baari baari cheak ki pr problum smj nai aayi plzz meri help kare esa ku ho raha h sir
👍🇹🇷🇹🇷🇹🇷👍Another great video..! We are waiting for your smps repair videos.. Greetings from TURKEY..
most welcome
Well done 👏✔👍👌
best regards
what is it that you say at the beginning of all your videos?
As-salamu Alaikum Warahmatullahi wabarakatuhu
“Peace be upon you and God's mercy and blessings.”
Peace be upon you. I have the same power supply, but it makes a buzzing sound and the output voltage is 16. There is no control over the variable resistor, and when loaded, the voltage drops. What is the reason?
Try to see the feedback line and if there the TL431 IC. The optocoupler works on the feedback system.