Great video as usual many thanks. You use parts from scrap power supplies. At which point do you decide a supply is scrap? I ask as you seem to fix most things.
Fitst thank you for sharing your knowledge. I really appreciate it 🙏🏼 Question: I live in Mexico (127VAC) and SMPS was switched to 220V (insted of 110V) so it get damaged during working for some time. Now is making a buzzing sound and switching on and off. Is this a similar damage?
Thank you sir. I have one question where is the optocoupler in this power supply ( or in another way , how they isolated the secondary portion fro the primary portion). again thanks a lot sir for all your help
Yo my main man Has! Has tell me, have you ever tinkered in upgrading 110v powertool chargers to 220v? I'm getting so tired of carrying around extra step down transformers because the cordless drills (for some weird reason) are always way cheaper in 110v! I have saved up for some Makita and Metabo HPT tools for jobsite BUT carrying around extra transformers is always a pain.
Peace be upon you. I have the same power supply, but it makes a buzzing sound and the output voltage is 16. There is no control over the variable resistor, and when loaded, the voltage drops. What is the reason?
Hello, Can you explain please why an smps that uses ml4800 IC, the vcc and reference voltages are low, instead of 13V on vcc it is 7v. The reference voltage also low instead of 5v.
My exact same smps provide voltage 12v output when connected with series lamp...when connected directly to supply, input fuse gets blown immediately...input voltage selection switch us set at 220v.
Aoa sir mere pass 24 v powersupply hai karab hu gaye thi mainey repair kia toh usmain musla araha hai k jaise transistor aur output diode lagao waise he transistor aur output diode short hu kar karab hu jaian hai toh sir yeh kia issue hai aur kahan se hai plz guide me ThQ Jazzak Allah
sir haseeb how are you i have power supply smps of satttelite receiver have 5 volt output without insering the cable in the motherboard port .Now when i connect the cable conductor in the same motherboard port power on the 5 volts is going to up down 4 volt 3.2 volt 2.58 volt etc please can you help to troubleshoot thanks
10:55 Sir, please don't teach us to regulate the output voltage WITHOUT any load. As you know, a lot of power supplies output higher voltage on idle, and then it drops to correct value when you apply the load.
Thank you Mr. Haseeb always for your instructive and informative videos!
it is my pleasure
ខ្ញុំចូលចិត្តវីដេអូរបស់អ្នក
Yaşasın Haseeb elektronik. Sevgi ve selamlar efendim.👍
حفظك الله من كل شر ورزقك من الطيبات.
Sir, you are our hero!
Be continue SIR by giving this type of power supply related video.
I will try my best
Another fantastic repair, above the excellent 👍
M.A
Many thanks!
Informative vedeo. Thank you so much. God bless you.
best regards
I really enjoy watching these videos, thank very much Sir.....🙏
So nice of you
Very informative. Thank you very much for sharing your knowledge. Not everyone can do that. 👍👍👍
Simply great!!! Thank you
You are welcome!
Thanks very much sir for sharing....
Most welcome
Very informative video 🎉
Excellent . Please sir explain how to working IGBT gate registance calculate. And capacitor charging and discharging time calculation. Thank you sir.
Thanks for sharing 👍
Excellent work , ❤
thank you. Now my power supply is working
You are welcome
Very good thank you ❤
You're welcome 😊
جزاك الله خير يا بشمهندس ❤
Excellent thanks for sharing
Mashaallah sir nice explanation
Thanks for sharing
It is my pleasure
wa'alaikum salam warohmatullaahi wabarokatuh😌
Salam Aleikum, very nice video !
Wa Alaikum Salaam Dear brother
Great video as usual many thanks.
You use parts from scrap power supplies. At which point do you decide a supply is scrap?
I ask as you seem to fix most things.
when the repair cost exeeds than the 65% of the actual cost. then i recommend to not to repair
Fitst thank you for sharing your knowledge. I really appreciate it 🙏🏼
Question: I live in Mexico (127VAC) and SMPS was switched to 220V (insted of 110V) so it get damaged during working for some time. Now is making a buzzing sound and switching on and off. Is this a similar damage?
Nice sir 👌👍
Thanks and welcome
Thank you sir. I have one question where is the optocoupler in this power supply ( or in another way , how they isolated the secondary portion fro the primary portion).
again thanks a lot sir for all your help
Sir I want to know how to test a transformer. Because you said high frequency don't try. Please sir help me
Hi Sir. For a chance will you have available the schematics for the same exact board you are working on here?
Thanks sir
Which reason it burned please
And when will you continue the video series of incomplete drive series
it gets damaged due to any high spike switching puse in startup circuit, that is from high power mosfets
@@HaseebElectronics thanks sir
please reply why do we have to supply power using a series lamp while testing pcb board
SIR WHATS THE PORTABLE MULTIMETER BRAND U USE FOR TESTING , WARUNA FROM SRILANKA , THANK U FOR THE VIDEO
i have in this video KAIWEETS KM6
and i also have following
FLUKE 15
FLUKE 77
FLUKE 179
Uni-T 202A+ clamp meter
thank u sir , we srilankans always watch ur videos , thank u sir @@HaseebElectronics
Yo my main man Has! Has tell me, have you ever tinkered in upgrading 110v powertool chargers to 220v? I'm getting so tired of carrying around extra step down transformers because the cordless drills (for some weird reason) are always way cheaper in 110v!
I have saved up for some Makita and Metabo HPT tools for jobsite BUT carrying around extra transformers is always a pain.
ماشاء اللہ
Nice video 😅❤❤❤❤❤❤😅😅😅😅😅❤❤❤❤ great
Many many thanks
السلام عليكم ورحمة الله وبركاته، كيف حالك أخي
لدي سؤال لدي جهاز يصدر طنين حتى بعد ما غيرت له القطع اللتي انتي غيرتها.
أرجو الإفادة
Peace be upon you. I have the same power supply, but it makes a buzzing sound and the output voltage is 16. There is no control over the variable resistor, and when loaded, the voltage drops. What is the reason?
Hello Sir i have a question, how this power supply output is 7v if both transistors are damaged?
Hello,
Can you explain please why an smps that uses ml4800 IC, the vcc and reference voltages are low, instead of 13V on vcc it is 7v. The reference voltage also low instead of 5v.
Asalamualikum In this bourd is a short circuit why the ciruos lamp not glowing
Can you make a video on dual output powersupply
🙏🏻👍🏻
Good
My exact same smps provide voltage 12v output when connected with series lamp...when connected directly to supply, input fuse gets blown immediately...input voltage selection switch us set at 220v.
Very well
Aoa sir mere pass 24 v powersupply hai karab hu gaye thi mainey repair kia toh usmain musla araha hai k jaise transistor aur output diode lagao waise he transistor aur output diode short hu kar karab hu jaian hai toh sir yeh kia issue hai aur kahan se hai plz guide me ThQ Jazzak Allah
Good
sir haseeb how are you i have power supply smps of satttelite receiver have 5 volt output without insering the cable in the motherboard port .Now when i connect the cable conductor in the same motherboard port power on the 5 volts is going to up down 4 volt 3.2 volt 2.58 volt etc please can you help to troubleshoot thanks
Sir please guide me equivalent to 2p4m scr i am your subscriber from india
NT5457
NTE5458
2P6M
T106M1
S4008FS21
C106M1G
TS420-600T
S4006LS2TP
🎉🎉🎉
Can i replace its 13007 transistor with 13009
Aoa diagram sir is supply ka kindly kahin show ker dain
I want to learn wiring diagram of SMPS.. please sir..
❤
Isn't it dangerous not to discharge the condenser, sir?
Many power supplies have in circuit discharge resistors; but just in case, he always checks the voltage anyway... at 2:30 in the video.
May be u don't know, Haseeb is a master, n big Engineer
My 12v smps no out put on secondary then I change ic 494 after the voltage is very hight 19v I can't regulate voltage
👍
best regards
Apne isme kya change Kiya hai
2sc1815 transistor - 2
1N4752 zener diode - 2
@@HaseebElectronics
Sir mere pass ek pcb hai usme 6-7v aarahe hai kya problem ho sakti hai
W slam
10:55 Sir, please don't teach us to regulate the output voltage WITHOUT any load.
As you know, a lot of power supplies output higher voltage on idle, and then it drops to correct value when you apply the load.
Dear sir, now I feel no deep thinking to repair p.s.u. If I join your channel ,
I shall get your advise to repair led tv.
alikom al Salam
Sir apne reply nhi Diya
👍