Yea that's how I feel, car was 2 different colors when I bought it and a boat load of dents. Now it's a lot less dents and one color I'm happy for a beater car
I had that harbor freight paint gun. It died after a few uses too. I now have the Finish Max Super paint sprayer. It was around $100 but it has the 2 stage trigger, pull it halfway and just air comes out then pull it fully and paint comes out. Its quiet and works great. I haven't used it for automotive paint....yet
That's what I'm saying, you set out and named the video airless spray gun, you have the money to spend 500 plus on paint. But you crap out on your own video and don't go buy another 20 - 30 dollar sprayer. I mean it's your choice and your own video, but you name it one thing and then don't follow through?
The Avanti gun Harbor Freight currently sells specifically states it has to be cleaned if you stop using it even with house paint or it will clog. Assuming the construction is similar and that what you encountered wasn't a mechanical failure I think you need to be prepared to do it in one uninterrupted session and be ready to clean it immediately after.
Mark you are the shit! Your AWESOME! Damn it I love it when you do videos like this. These are my favorite. Never in a million years did I think that an electric spray gun would work at all much less how it turned out! Thanks again man for the great content! My favorite channel 100%
Did just what you did in 1972 to a Chevy II with the OEM paint color ... besides being dull it covered the car well and lasted many years ... got used to the dull finish and kind of liked it. Good job in ALL and loved talking in the RAIN and painting the tires and wheels.
So as I'm watching this I'm wondering if I should try this on my S10, I have like 1100.00 in the truck and it's like 5 different colors. I really like the gray color you used . In your opinion did the electric gun do a good enough job to use with a single stage paint?
I have one of these spray guns and used it to put stain on my fence. It spit globs of stain unexpectantly and then sometimes wouldn't spray at all and clog up. They really are a cheap piece of crap. I had to buy two guns because they only last a few times of use. I'm surprised that you were able to get it to spray as smooth as you did
That nardo gray looked like it layed down really good from an internet distance but couldn't really tell what the base was gonna do. I think the problems with airless/compressorless, both this one and the turbine type, is gonna be the hot pump and the hot air from the turbine. It will change the flash times dramatically and leave alot of dry spots. It was worth a shot but not something I would do if there was any way around it.
My Wagner gun seems to leak a bit of paint into the "motor" which if not cleaned up immediately after the painting session could ruin the gun. So remember to do this each time you rest for more than 10 minutes or at the end of your session. The gun is still going strong ater almost 30 years, although I think it might benefit from a new nozzle. Also to minimise overspray and orange peel, paint the roof separately while masking everything else. Additionally I found it beneficial to remove the bonnet and boot and paint them separately, on a slight incline rather than completely horizontal or vertical. The finish achieved here is better than I got (not by a mile though), but then I completed the job with the electric gun.
Looks a lot better than it was. I wasn't expecting the cheap airless gun to even work at all. I believe it would have been a nice job if the gun wouldnt have crapped out. Love the look of the car.
I still say its great with what u had to work with .I'm not saying that every car painter should do this still its great for what u did to show what can be done in a pinch
no man. this is good... just curious what was your mix in the wingwang? Paint Activator Pearl(tbl spoon) Hardner and more basecoat? HB has them for $27.99 right now as soon as you walk in the door! good job
I like the review on this gun. Nice video. How difficult is it to clean once done prior to use the base coat on it and or clear prior to dying on u? I keep wanting to drive out to your location for leave you my little Sentra hooptee to paint for me but I have to get rocket panels and quarter panel repaired first due to rust
I'm not gonna lie, I'm a little disappointed you didn't finish the job with another gun. I followed both parts and really wanted to see the finished result with this sprayer. Out of interest, what did you use to clean the gun out with?
Watched Pt1 and Pt2. I have been curious about how possible using an airless sprayer might be. After watching these 3 vids, now I'm curious how hood a novice painter using the best equipment might compare with a pro using the "wrong" tool. ...lol Speedkote could beat me using a roller!
I’m going to try this with my graco tc pro airless. Can you recommend a brand/ type of paint/ primer that would work best with this? Also the clear coat. I know less sheen = less visible imperfections, but in general is there a color that hides better also? Thanks for this unique content.
Beautiful job mate! I first used one five years ago when I painted my Toyota Celica bumper and I was amazed that the job Turned out perfect than a rattle can. I decided to buy myself a cordless one and didn't get around to buying the rechargeable batteries. I just bought a recarable polisher and the 21v300 battery I can use with my paint spray🤣🤣 so my next job with be painting my Toyota Caldina Gt4 N spec Bumper. I bought this car two years ago and now getting around to fixing the little issues this came with. I had an old Honda Integra back in 2011 and the paint work was horrible so I used rattle cans the job was horrible and truly wish I had these electric paint guns that would have turned out better. Well done to you for making this video. Perfect job🎉. 🍺
Ain’t gone lie. Look good. I wanna see the avanti gun by harbor freight primer paint and clear coat video. Not many electric sprayer spaying cars on RUclips.
I'm getting a plastic front lip for an 02 Camry that will need to be painted and I thought about just getting the color match spray can is that can cost what $15- $17 a can If I could spend $40 on a sprayer like that just to do a 5ft long plastic piece
how many watts was the spray gun? and can it also spray clear or not? ( i know that a hvlp is much better with clears but i don't have a setup just yet)
this works quite well its a perfect way to paint a truck your going in the woods with thats gona get scratched up or a utility truck/car thats used to work
Great job brother, it looks like a young fella,s Friday night cruiser... Color suit the car, sweet as finish 🎉. $150 finish I'd be happy with that. ❤from New Zealand supporters ❤
Why didn't you mask off the tires you got all over them. lol Besides that great job I'm going to buy one at hobo freight now that I have seen your video. I am only fixing chipped paint spots on my Buick with color code matched paint. Then some on my f150. So it should not crap out on me too.
I get why paint jobs cost so much, but body/painters don't understand alot of people do not have the money. And let's be real. Part of the reason they cost so much is because shops want that ins. Money not private money. I got a quote for anywhere from 1500 to 3000 to paint my fender flares and my vent visor/rain guards. That is an insane amount of money. I don't give a sh1t what these painters think of themselves. That is t a rational price. I came to the conclusion they didn't want the work but if I was stupid enough to pay those idiotic prices they would do it. I bought 180 dollars of exact paint from Sherwin Williams commercial and a paint gun, taped off a paint booth in my garage hung em amd painted em. They orange peeled a little but but I literally saved thousands. Sanded em down real good and good to go. I am a hard headed will not pay it if I don't see the value kind of person amd on a clean surface printable product I couldn't pay em. I'm am electrician and if we acted like most body shops none of yall would have power. All you hear about is the work, the work. Every single job is work. But paint is absurdly high. I do get alot of it is materials though. That's the crazy part is how high paint actually is. Anyways. Thanks for this video. I've got a beater 1990 gmc that's great except the paint and my buddy said 8k. And I would be stupid to pay him that. I said your damn right. I bought it for 5k. I just can't pay that knowing what I use it for, which is a work truck. This is my new plan of action if this guy lined up to now buy it falls through. Paint and send it.
Unfortunately just can't change the prices of services. T bone steaks are super expensive as well, that's why there's a steak house and a McDonald's in every town so people can pick and chose what quality they want.
Considering that those paints ain't even formulated for such a spray gun, it's a miracle that this thing even works, and if enough people ask the manufactures to make a specialty formulate paint for this kind of sprayer maybe we can have much better results, I'm pretty sure that there's a market for that, given the extremely low price to enter the business. And of course, there are way better electric sprayer, those that often called "turbine sprayer" and people use them a lot for furniture.
@@speedokoterefinishnetwork4937 love the content bro keep it up👌 hopefully one day I paint my car too. you think you could do a white pearl? Never seen you do one before
I bought that same HF gun for home use. it was total junk and had a ton of paint splatters and it was barely good enough for one job before no longer working. The cheaper spray gun I got off amazon was much better and reusable.
I just recently bought this paint sprayer I’m confused because people keep telling me different things. What paint do I use for the sprayer gallon house paint?or car paint? Probably sounds stupid but I’ve never painted a car before so I have no clue🤷🏼♂️ any information would be much appreciated.
Lol I understand where you’re coming from, but the type of person I am I could care less about how it looks. Any paint job is better than what I have now lol. So if you don’t mind me asking if it’s car paint where would I find it at? Or do I have to order it online? Because all I’m finding is the spray cans not the gallon
I went on speedokote and put in the color code for Camellia red and wanted to order a gallon of base coat. It didn't give me a price even whenever I went to check out and billing. It says free shipping and then no cost for the product. My question is if I pre-order it I don't know how much the paint is going to be. So do I pre-order it and then they'll send me an email saying how much is going to cost and then verify that I want to buy it?
@@speedokoterefinishnetwork4937 yeah I used y'all's glamour clear recently and it really came out nice! 👍 So far I've been using base coats by auto hq off eBay and had good luck. I've been working for myself and started with flipping Hondas and painting them and it's been almost a year now! First car I painted was my personal 92 Acura integra with the speedokote bright white single stage and it came out beautiful. I've painted two full cars and a custom set of rims since then I've been working on my experience with base clear. Also currently doing a full jamb job and color change to Nevada beige on a 93 Toyota pickup. Just did the jambs and finished it off with the glamour clear and Damn it is nice 👍 . I'm really looking forward to the speedokote option for the any color code base coat because if it's as good as y'all's clear coat I want it! 🤣
@@speedokoterefinishnetwork4937 and thank you for checking into it. I was really confused when I went to check out and it didn't state a price after filling out all the info. I have an account as well I've bought products from y'all before and never had an issue.
That is a smoking color man, for a beater car that thing turned out nice. I have an electrical spraygun from Adendorff and been using it for a while now, but never automotive, will try that next.
Electric spray guns generally don't spray well using thin paint. They are meant to spray thicker paints and they will burn up using thin paint and sometimes even dry within itself clogging up the gun rendering it useless
@Speedokote refinish network I normally use a Black Widow from Hobo Freight and it has worked very well for the last 4 paint jobs I've done. Royal blue pearl metallic/clear, metallic gun metal grey/single stage, midnight black/clear and torch red/single stage. My next project will be a 2012 Dodge Challenger for my youngest son that I'll sand down with 600 or 800 grit and then shoot with grey sealer and the Speedokote single stage Nardo grey. I saw you use it on one of the cars you painted and I figure 3 coats and I can have it gleaming. But now I'll have to find another air compressor since I sold my Husky 60 gallon. I think a good 40 gallon should work fine unless I can find a 120v 60 gallon at a really good price. Lol
You can get a very good Fuji Turbine system for about the price of very good spray gun.Check out some of the vids here on the tube.There is a learning curve,but since your already a painter it will be easy.
Amazon has way better turbine spray guns, most come with removable 1-2.0 sized tips and lay down pretty good. I painted a car in color shift paint with a $20 gun off Amazon and it looks great.
Harbor Freight used to sell a turbine paint sprayer for $100. I wish I had gotten it before it was discontinued. I wanted to try it. Definitely better than the home sprayer. It would have to be
Very good 👍😊 motivates me to go ahead paint 🎨 my truck for the first time time I'm excited I've been finishing my body work have a little more to go then it's ready to paint 🎨
every week. This was 2 sec short video :). Hey I was like, yeah, this could work. I was a bit angry for not go and buy another one to finish it. Good job!
I see was pretty close with the synergy green guess. Didn’t know Chrysler had their version. If you go this color again, try putting down a silver ground first for fast coverage. The color looked good, and hey, @ least you tried. Next time try one from walmart😂
![I.N "HALLUCINATION" | [Stray Kids : SKZ-PLAYER]](http://i.ytimg.com/vi/n5B5q1Hwt_U/mqdefault.jpg)
Not show car quality but a million times better than faded, peeling, delaminating, and/or damaged. Thanks for uploading this👏
Yea that's how I feel, car was 2 different colors when I bought it and a boat load of dents. Now it's a lot less dents and one color I'm happy for a beater car
I had that harbor freight paint gun. It died after a few uses too. I now have the Finish Max Super paint sprayer. It was around $100 but it has the 2 stage trigger, pull it halfway and just air comes out then pull it fully and paint comes out. Its quiet and works great. I haven't used it for automotive paint....yet
It will work
Awesome job. Luv the channel because it caters to the common person working in the driveway.
Thanks!
Justo el video que necesitaba, se agradece tu explicación ya que pintaré el mío, saludos desde Chile.
Why didn't you go buy a new spray gun
That's what I'm saying, you set out and named the video airless spray gun, you have the money to spend 500 plus on paint. But you crap out on your own video and don't go buy another 20 - 30 dollar sprayer. I mean it's your choice and your own video, but you name it one thing and then don't follow through?
That just tells me not to buy it or get 2 in order to get this thing finished.
However it is harbor freight. If they made everything to last, they wouldn’t make money.
@@BEAZY_5150Yeah but it's a 90 day return policy on the items. He could have returned the gun and got a new one for free.
yeah that would be much better
The Avanti gun Harbor Freight currently sells specifically states it has to be cleaned if you stop using it even with house paint or it will clog. Assuming the construction is similar and that what you encountered wasn't a mechanical failure I think you need to be prepared to do it in one uninterrupted session and be ready to clean it immediately after.
You are exactly correct. I use mine with house paint for doing vents, louver doors, and such. If you stop, you clean it. If you don’t, it’s trash.
Why didnt you just go buy another airless gun to finish the experiment.
Mark you are the shit! Your AWESOME! Damn it I love it when you do videos like this. These are my favorite. Never in a million years did I think that an electric spray gun would work at all much less how it turned out! Thanks again man for the great content! My favorite channel 100%
Thanks!!
Did just what you did in 1972 to a Chevy II with the OEM paint color ... besides being dull it covered the car well and lasted many years ... got used to the dull finish and kind of liked it. Good job in ALL and loved talking in the RAIN and painting the tires and wheels.
Thank you for being a pioneer in this industry! This is a paint job within reach for almost anybody
Pretty much yes!
So as I'm watching this I'm wondering if I should try this on my S10, I have like 1100.00 in the truck and it's like 5 different colors. I really like the gray color you used . In your opinion did the electric gun do a good enough job to use with a single stage paint?
I have one of these spray guns and used it to put stain on my fence. It spit globs of stain unexpectantly and then sometimes wouldn't spray at all and clog up. They really are a cheap piece of crap. I had to buy two guns because they only last a few times of use. I'm surprised that you were able to get it to spray as smooth as you did
That nardo gray looked like it layed down really good from an internet distance but couldn't really tell what the base was gonna do. I think the problems with airless/compressorless, both this one and the turbine type, is gonna be the hot pump and the hot air from the turbine. It will change the flash times dramatically and leave alot of dry spots. It was worth a shot but not something I would do if there was any way around it.
Love the color. Nice job. Looks great to me. Take care!
Thanks !
My Wagner gun seems to leak a bit of paint into the "motor" which if not cleaned up immediately after the painting session could ruin the gun. So remember to do this each time you rest for more than 10 minutes or at the end of your session. The gun is still going strong ater almost 30 years, although I think it might benefit from a new nozzle.
Also to minimise overspray and orange peel, paint the roof separately while masking everything else. Additionally I found it beneficial to remove the bonnet and boot and paint them separately, on a slight incline rather than completely horizontal or vertical.
The finish achieved here is better than I got (not by a mile though), but then I completed the job with the electric gun.
Good point !
I think this is more of a statement on your ability as a painter than it is the application type. goodjob!
Yup that's basically my whole point of the video
Yep. This paint sprayer in my hands would create a right mess!!
Looks a lot better than it was. I wasn't expecting the cheap airless gun to even work at all. I believe it would have been a nice job if the gun wouldnt have crapped out. Love the look of the car.
This is great. Unrelated question, how do you deal with dust particle painting in the open like that?
Wet the ground grab a tarp
That’s AWESOME!!!! Looks like it works well for what you’re doing!! How well does it work with metallic colors??
Crap lol!
Great job really
I still say its great with what u had to work with .I'm not saying that every car painter should do this still its great for what u did to show what can be done in a pinch
Do you place a cover over the engine bay since you are spraying over the hood? Wouldn't overspray seep inside?
Usually mask engine bay
@@speedokoterefinishnetwork4937 thank you!
Hello just a question. For the bumper did u used the same primer as the body?
Yes
no man. this is good...
just curious
what was your mix in the wingwang?
Paint
Activator
Pearl(tbl spoon)
Hardner
and more basecoat?
HB has them for $27.99 right now as soon as you walk in the door!
good job
Paint
1 part paint 1.5 parts reducer
Smr1150 clear 4-1
@@speedokoterefinishnetwork4937 thank you!! Blessings
I like the review on this gun. Nice video. How difficult is it to clean once done prior to use the base coat on it and or clear prior to dying on u?
I keep wanting to drive out to your location for leave you my little Sentra hooptee to paint for me but I have to get rocket panels and quarter panel repaired first due to rust
Well I threw mine away so I wouldn't know 😂
I'm not gonna lie, I'm a little disappointed you didn't finish the job with another gun. I followed both parts and really wanted to see the finished result with this sprayer. Out of interest, what did you use to clean the gun out with?
I understand
Great video's, always good to have something that inspires. How much paint did you use?
About a gallon 🙂
Watched Pt1 and Pt2. I have been curious about how possible using an airless sprayer might be.
After watching these 3 vids, now I'm curious how hood a novice painter using the best equipment might compare with a pro using the "wrong" tool.
...lol Speedkote could beat me using a roller!
I was wondering what rims you have on there? I have an 08 civic lx coupe, want to get rims but know nothing about it, you made that car look amazing!
These are just some cheapos the owner included . No idea to be honest lol
I’m going to try this with my graco tc pro airless. Can you recommend a brand/ type of paint/ primer that would work best with this? Also the clear coat. I know less sheen = less visible imperfections, but in general is there a color that hides better also? Thanks for this unique content.
Anything low solids should work
Question::: say the primer has been on the car for awhile like 2 years... is it good to still paint over...
With some sanding it's possible
can i do 4 parts acetone and 3 parts paint ? and add hardener?
?
you should do another video with using the airless gun but having one for base and one for clear to really know the results 😅
Beautiful job mate! I first used one five years ago when I painted my Toyota Celica bumper and I was amazed that the job Turned out perfect than a rattle can. I decided to buy myself a cordless one and didn't get around to buying the rechargeable batteries. I just bought a recarable polisher and the 21v300 battery I can use with my paint spray🤣🤣 so my next job with be painting my Toyota Caldina Gt4 N spec Bumper. I bought this car two years ago and now getting around to fixing the little issues this came with. I had an old Honda Integra back in 2011 and the paint work was horrible so I used rattle cans the job was horrible and truly wish I had these electric paint guns that would have turned out better. Well done to you for making this video. Perfect job🎉. 🍺
Thanks!
Ain’t gone lie. Look good. I wanna see the avanti gun by harbor freight primer paint and clear coat video. Not many electric sprayer spaying cars on RUclips.
I was planning on doing this too. How is the overspray, im paranoid on getting it on neighbors cars
Not to bad
should have bought two those are known for just dying no matter what you run through them
Love that old school two bay ' barndominium ' in the background early in the video.
Perfect for an old bachelor like me. lol.
What kind of paint are you using?
I'm getting a plastic front lip for an 02 Camry that will need to be painted and I thought about just getting the color match spray can is that can cost what $15- $17 a can
If I could spend $40 on a sprayer like that just to do a 5ft long plastic piece
Would stick to the spray can stuff. Definitely do proper prep
HI what clear did you use good job🙂
Speedokote
Hey Mark you should make a video on how to mask a car for a cheap paint job!
Ok!
You should of spraid with lacquer thinner to keep the spray gun clean and clear.
Dam that color looks awesome on that car.
Thanks 🙏
What type paint & thinner?? And does that gun hold prime?
will an electric HVLP sprayer work with silver metallic and clear coat?
It's possible wouldn't recommend
how many watts was the spray gun? and can it also spray clear or not? ( i know that a hvlp is much better with clears but i don't have a setup just yet)
No idea on wattage
That electric spray gun is about to be sold out after this video hits large great job
Probably 😂😂😂
👌🏾
It broke and the video was pointless because he couldn't even finish with it. If you still buy it you're special.
Looks cool as shit for sure. Super improvement and I love the custom mirrors 😂😂😂🎉🎉🎉🎉
Thanks!
Why not spent 5 mins and cover all the tires?
☹️
I threw them out that's why 😂
Awesome job, I wish you were near Charlotte, NC
Only about 8 hours
this works quite well its a perfect way to paint a truck your going in the woods with thats gona get scratched up or a utility truck/car thats used to work
Great job brother, it looks like a young fella,s Friday night cruiser...
Color suit the car, sweet as finish 🎉.
$150 finish I'd be happy with that.
❤from New Zealand supporters ❤
Thanks!
Why didn't you mask off the tires you got all over them. lol Besides that great job I'm going to buy one at hobo freight now that I have seen your video. I am only fixing chipped paint spots on my Buick with color code matched paint. Then some on my f150. So it should not crap out on me too.
Lol did you really think I was going to ride this car on steelies after a nice paint job?heck no. Trashed them
I get why paint jobs cost so much, but body/painters don't understand alot of people do not have the money. And let's be real. Part of the reason they cost so much is because shops want that ins. Money not private money. I got a quote for anywhere from 1500 to 3000 to paint my fender flares and my vent visor/rain guards. That is an insane amount of money. I don't give a sh1t what these painters think of themselves. That is t a rational price. I came to the conclusion they didn't want the work but if I was stupid enough to pay those idiotic prices they would do it. I bought 180 dollars of exact paint from Sherwin Williams commercial and a paint gun, taped off a paint booth in my garage hung em amd painted em. They orange peeled a little but but I literally saved thousands. Sanded em down real good and good to go. I am a hard headed will not pay it if I don't see the value kind of person amd on a clean surface printable product I couldn't pay em. I'm am electrician and if we acted like most body shops none of yall would have power. All you hear about is the work, the work. Every single job is work. But paint is absurdly high. I do get alot of it is materials though. That's the crazy part is how high paint actually is. Anyways. Thanks for this video. I've got a beater 1990 gmc that's great except the paint and my buddy said 8k. And I would be stupid to pay him that. I said your damn right. I bought it for 5k. I just can't pay that knowing what I use it for, which is a work truck. This is my new plan of action if this guy lined up to now buy it falls through. Paint and send it.
Unfortunately just can't change the prices of services. T bone steaks are super expensive as well, that's why there's a steak house and a McDonald's in every town so people can pick and chose what quality they want.
Considering that those paints ain't even formulated for such a spray gun, it's a miracle that this thing even works, and if enough people ask the manufactures to make a specialty formulate paint for this kind of sprayer maybe we can have much better results, I'm pretty sure that there's a market for that, given the extremely low price to enter the business.
And of course, there are way better electric sprayer, those that often called "turbine sprayer" and people use them a lot for furniture.
Yes agree
What if you try the other harbor freight electric paint sprayer? The handheld avanti hvlp sprayer. Wonder if it has better results🤔 it’s 90$
Going to try one off Amazon
@@speedokoterefinishnetwork4937 oh okay lol wanted to see if that avanti one was any good on painting cars
@@speedokoterefinishnetwork4937 love the content bro keep it up👌 hopefully one day I paint my car too. you think you could do a white pearl? Never seen you do one before
@@dirtysanchez4042 white pearl is easy
Can it be done with electric spray gun
I tried looking up the paint is that the same as gecko green Pearl? That’s the only one I could find
Yea the same I think
That grey went on quick !! And color looks nice !
Yes!
I bought that same HF gun for home use. it was total junk and had a ton of paint splatters and it was barely good enough for one job before no longer working. The cheaper spray gun I got off amazon was much better and reusable.
I just recently bought this paint sprayer I’m confused because people keep telling me different things. What paint do I use for the sprayer gallon house paint?or car paint? Probably sounds stupid but I’ve never painted a car before so I have no clue🤷🏼♂️ any information would be much appreciated.
If you really want to paint a car the right way don't use this. Lol
Lol I understand where you’re coming from, but the type of person I am I could care less about how it looks. Any paint job is better than what I have now lol. So if you don’t mind me asking if it’s car paint where would I find it at? Or do I have to order it online? Because all I’m finding is the spray cans not the gallon
What color do you want to paint it
Matte black
Can you actually get a decent auto paint job with an electric sprayer?
Not really
it looks that you missed to mask the tyre?
Didn't care, they were being trashed..
Was just checking to see if you posted. Good timing
Thanks!
Is it better or worse than a spray can ?
Mabey a hair better
You dont need cover tires when painting
These were junk tires I threw them on just for the paint job
@@speedokoterefinishnetwork4937 oh ok I see. Thanks
I went on speedokote and put in the color code for Camellia red and wanted to order a gallon of base coat. It didn't give me a price even whenever I went to check out and billing. It says free shipping and then no cost for the product. My question is if I pre-order it I don't know how much the paint is going to be. So do I pre-order it and then they'll send me an email saying how much is going to cost and then verify that I want to buy it?
I'll have to verify this Monday. I will say it used there base it covers better than anything I've ever used
@@speedokoterefinishnetwork4937 yeah I used y'all's glamour clear recently and it really came out nice! 👍 So far I've been using base coats by auto hq off eBay and had good luck. I've been working for myself and started with flipping Hondas and painting them and it's been almost a year now! First car I painted was my personal 92 Acura integra with the speedokote bright white single stage and it came out beautiful. I've painted two full cars and a custom set of rims since then I've been working on my experience with base clear. Also currently doing a full jamb job and color change to Nevada beige on a 93 Toyota pickup. Just did the jambs and finished it off with the glamour clear and Damn it is nice 👍 . I'm really looking forward to the speedokote option for the any color code base coat because if it's as good as y'all's clear coat I want it! 🤣
@@speedokoterefinishnetwork4937 and thank you for checking into it. I was really confused when I went to check out and it didn't state a price after filling out all the info. I have an account as well I've bought products from y'all before and never had an issue.
😂 can u spray clear with that electric gun? Thanks
I wouldn't but anything is possible
I like your videos,looking forward to more content
Thanks!
That is a smoking color man, for a beater car that thing turned out nice. I have an electrical spraygun from Adendorff and been using it for a while now, but never automotive, will try that next.
Yea exactly this is just a beater paint job. I was happy with it
Electric spray guns generally don't spray well using thin paint. They are meant to spray thicker paints and they will burn up using thin paint and sometimes even dry within itself clogging up the gun rendering it useless
Yup agree
@Speedokote refinish network I normally use a Black Widow from Hobo Freight and it has worked very well for the last 4 paint jobs I've done. Royal blue pearl metallic/clear, metallic gun metal grey/single stage, midnight black/clear and torch red/single stage. My next project will be a 2012 Dodge Challenger for my youngest son that I'll sand down with 600 or 800 grit and then shoot with grey sealer and the Speedokote single stage Nardo grey. I saw you use it on one of the cars you painted and I figure 3 coats and I can have it gleaming. But now I'll have to find another air compressor since I sold my Husky 60 gallon. I think a good 40 gallon should work fine unless I can find a 120v 60 gallon at a really good price. Lol
Looks good💪🏽
Where you located?
Thanks, pa
Damn someone just gave the plain facts thank you bro
Absolutely
After this I’m opening my own painting business! Great work! Hey it’s not the best but it looks good! I’m SOLD! SUBSCRIBED!
Thanks a lot!
What size nozel you used?
The one that came with it can't remember size
Awesome job! 👍
What’s the name of the Grey again I’m going to do that on my 88 f700
Nardo gray
You can get a very good Fuji Turbine system for about the price of very good spray gun.Check out some of the vids here on the tube.There is a learning curve,but since your already a painter it will be easy.
You are a brave man spraying a metallic with a gun like that!
Yea first coat I was pulling my hair out 😂
What is the paint code?
Did it fail or did it clog?
Not 100% sure no time to diagnose it had to keep spraying
You should retry this with the new avanti hvlp from harbor freight
When I have another car to do this with sure
you got to be kidding me man! WOW! dude great job!
Hey I tried
I did the same with a car with enamel paint .the reason why you gun died you didn't clean it In between coats .
Oh ok I had no idea
Very nice, I thought you might have picked up a 2 nd cheap electric spray gun, but very nice
Man I was so frustrated I said screw it and just grabbed the spray gun 😂😂
Amazon has way better turbine spray guns, most come with removable 1-2.0 sized tips and lay down pretty good. I painted a car in color shift paint with a $20 gun off Amazon and it looks great.
Looked good after the base gray.
Electric tools from Harbor freight don't really last but if it's a name brand spray gun it would last you for ever.
Harbor Freight used to sell a turbine paint sprayer for $100. I wish I had gotten it before it was discontinued. I wanted to try it. Definitely better than the home sprayer. It would have to be
Amazon sells all kinds of electric turbine sprayers. They actually spray great.
You cheated, I wanted to see the top coat done with an electric sprayer.
Very good 👍😊 motivates me to go ahead paint 🎨 my truck for the first time time I'm excited I've been finishing my body work have a little more to go then it's ready to paint 🎨
Great!
every week. This was 2 sec short video :). Hey I was like, yeah, this could work. I was a bit angry for not go and buy another one to finish it. Good job!
Man a simple wet sand and buff would be a show car finish paint look very clean
Trueb
I used one of these electric sprayers to paint my bakflip tonneau cover and it worked great.
Are you James from DONUT?
No lol
That looks freaking awesome
Turned out amazing.
Thanks!
I see was pretty close with the synergy green guess. Didn’t know Chrysler had their version. If you go this color again, try putting down a silver ground first for fast coverage. The color looked good, and hey, @ least you tried. Next time try one from walmart😂
Boush made a spray Gun for wood and wall try That a have great result
Crikey what a difference to when you started you'd think it wasn.t the same car.
True !!
Didnt look like it had gobs of overspray either... like fogging up the whole block. Nice test..too bad it gummed up.
Yea i was bummed a little
Too bad it crapped out. Shoulda bought 2, I guess...but ya went ahead and finished it out and not too shabby
Yes! I'll be doing another video with a cheapo Chinese spray gun soon