@blesstv5 those ones from various truck stops like iowa 80, joplin petro etc.. youre better off searching dual revolution 3/4" lights on amazon. At the truck stops theyre like $18 per light, on amazon you can get 10 for $30 and theyre nice and bright too. Much more worth it!!!
Nice vid. A couple of questions if you don’t mind. Where did you get your lights at? I’m want to make the lights to work as turn signal lights as well. Would the lights you installed work as such? TIA.
@abs1913 you can get them at any main truck stops. Id recommend getting some generic dual revolution lights off amazon though. You can get 10 for like $30 and they're between $15-$18 a piece at truck stops. You can run them to work as turn signals as well, just run a wire to something tied into your directionals and splice it into the mix!! Thanks for watching btw!
@@justanotherotrguy thank you much. I’ve been looking at some but I like the ones you installed because they are ready to plug and play. You don’t have to be doing any termination. Thank again and keep making the vids. They help some of us for sure…. Keep trucking!!
@abs1913 id honestly recommend splicing instead of the plug and plays. Theyre easier, yea. But they corrode and disconnect and stuff super easy. Every other lights ive done have been spliced and theyre holding strong. Both work, the p&p ones will eventually need to be fixed
@mathewben505 i bought the panels in person at bobs chrome zone in the flying j parking lot in lake station indiana. I got all the dual revolution lights there too. They are awesome there
Do you connect this directly to the factory marker lights? Or you have to install a relay too?? I have a 2019 Cascadia and want to do this to my truck. Thanks in advance.
Connected all the aux wires in the visor lights and connected them to a 16 gauge wire from behind the center clearance light behind the cb tray. Then ran it down to the driver side pillar and through the dash (behind the steering column) to my spare (blue light) switch. Easy peasy
Thanks dude this helps me with my t680
Absolutely!! Any time man. Hopefully you stick around!
Whered you buy the panels? I have the lights just looking for the panels
I came here to ask the same question lol
@davidturcios5832 bobs chrome zone in the flying j parking lot in lake station indiana. Off ripley street
Thanks for the detailed video 👍
Any time!!
🤷
Where did you the those lights from
@blesstv5 those ones from various truck stops like iowa 80, joplin petro etc.. youre better off searching dual revolution 3/4" lights on amazon. At the truck stops theyre like $18 per light, on amazon you can get 10 for $30 and theyre nice and bright too. Much more worth it!!!
Nice vid. A couple of questions if you don’t mind. Where did you get your lights at? I’m want to make the lights to work as turn signal lights as well. Would the lights you installed work as such? TIA.
@abs1913 you can get them at any main truck stops. Id recommend getting some generic dual revolution lights off amazon though. You can get 10 for like $30 and they're between $15-$18 a piece at truck stops. You can run them to work as turn signals as well, just run a wire to something tied into your directionals and splice it into the mix!! Thanks for watching btw!
@@justanotherotrguy thank you much. I’ve been looking at some but I like the ones you installed because they are ready to plug and play. You don’t have to be doing any termination. Thank again and keep making the vids. They help some of us for sure…. Keep trucking!!
@abs1913 id honestly recommend splicing instead of the plug and plays. Theyre easier, yea. But they corrode and disconnect and stuff super easy. Every other lights ive done have been spliced and theyre holding strong. Both work, the p&p ones will eventually need to be fixed
Hello hope all is well where did you get the set up from can you add the link @@justanotherotrguy
@mathewben505 i bought the panels in person at bobs chrome zone in the flying j parking lot in lake station indiana. I got all the dual revolution lights there too. They are awesome there
Do you connect this directly to the factory marker lights? Or you have to install a relay too?? I have a 2019 Cascadia and want to do this to my truck. Thanks in advance.
I connected them directly to the marker lights. That way when the markers come on, they all do!
How did you run auxiliary cable to visor?
Connected all the aux wires in the visor lights and connected them to a 16 gauge wire from behind the center clearance light behind the cb tray. Then ran it down to the driver side pillar and through the dash (behind the steering column) to my spare (blue light) switch. Easy peasy
Perfect thank you for the information.
@@2123dgr any time! Hope to see you comment on my other uploads!
Where did you get the panels?
@@2123dgr bobs chrome zone in lake station indiana in the flying j parking lot
KEEP EM COMIN’!
legend