Good video but being a aircraft mechanic I’m constantly amazed most auto mechanics do not use specific torques on Newley installed components. These bolts should be torqued to 65-87 foot pounds. Never use a impact wrench to tighten you can over torque and damage hub flange. Overall good video
I make aircraft parts. Everything on a plane, spacecraft, or nuclear submarines have to be very precise. Even a hundred thousands of an inch off can ruin a part. The stuff we deal with is more sensitive stuff than a car I guess.
I test drove a 2006 Optima yesterday with 123k miles, considering if I want to purchase. I did hear some grinding noise, front right. Brake pads were new, but rotor looks worn slightly. With experience from another car, I believe it could be the bearing. Your video has been the best video on how to change the bearing I've ever seen!! Excellent POV and talking through the process. I will subscribe to your channel.
I was going to pound out one broken stud , where a portion of the dust shield is cut. Now I see I can do the hub, which I have seen over-complicated videos posted. This video takes the reluctance to tackle this away. Thanks
Great video bro, I can now help my daughter out with her 2015 Kia Optima. She needs 2 wheel studs replaced and this video showed me how to just replace the whole assembly. Thank you so much.
Hi friend. what a great video. I am a visitor from Mexico. I thank you for the video now I know how to do the procedure to change those hubs and the cv axles, I have to do complete maintenance on the front suspension and I have a buzzing noise in the hubs so I will change them. Greetings again and you have a follower from Mexico.
2013 Hyundai Sonata doesn’t have a unitized hub assembly as in this video. Mine has the hub bearing press fit in the steering knuckle and the hub press fit through the bearing which equates to more work. Great video though but I do believe different model years were equipped differently. 😉
Did you end up doing this job on your own? Went to parts store and Kia dealer and bearing has to be pressed in which I was about to do until the guy told me the tool was $170.
What you can do is buy the new bearings and take off the old one and take it to a shop that can press in and out the bearings that way they can't charge you too much because they didn't take off the parts
@@DULLAHGOSOHARD or if you’re mechanically inclined for to harbor freight buy a fwd bearing puller. You still need a puller to pull the hub shaft out the bearing. Then you have to cut the inner race off the hub shaft. So if it’s a one time thing go to a shop. If you doing it all the time well then I’d equip myself with the necessary tools to be speedy and quality savvy. Honestly if you’re here asking all these questions I’d just take it to a shop.
This worked perfectly for my 2015 Hyundai i40 (same part). Only difference is mine was no where near as clean and had to be beaten repeatedly with a hammer before it came out!
Sob, newer version has bolt on bearings? I have the press in. (Really only watching to see if i gotta buy a new wheel hub or not, dont feel like messing with the brace though im fully capable of removing it if i take it to work 😂......im lazy)
I just bought new loaded left and right steering knuckle assembly from Canada. I have a 2013 kia optima sx turbo corsa blue loaded off the showroom floor. 131k on the car. Kia replaced my engine free of charge after major engine failure 4k ago. Just did the first oil change the other day. Drove to Colorado and back home on a quick trip. I bought the set I got because it has everything all pre loaded. The sx turbo in the first 5 months of 2013 is completely different with soo many weird parts. I've kept this car going after all these years. She gets down. Wish I could replace the hub/bearing assembly on my kia this easy but nope. It's all good. The new setup looks alot stronger!
@@abzalmohammed1184 where is the steering knuckle? Rack and pinion? Is that the full steering rack. My car feels like it’s all over the road. One minute it’s fine.
links for the part is here
kia Optima amzn.to/2JBDSu8
Hyundai sonata amzn.to/2LBcjUw
Dullah Goso hard what year is the optimal kia that you changed wheel bearings
Nice job that is so much easier than a 2008 optima where you got to press the bearing in and out and the hub assembly
Good video but being a aircraft mechanic I’m constantly amazed most auto mechanics do not use specific torques on Newley installed components. These bolts should be torqued to 65-87 foot pounds. Never use a impact wrench to tighten you can over torque and damage hub flange. Overall good video
I make aircraft parts. Everything on a plane, spacecraft, or nuclear submarines have to be very precise. Even a hundred thousands of an inch off can ruin a part. The stuff we deal with is more sensitive stuff than a car I guess.
How was the process of getting the A&P... And where do you think the industry is heading ?
I test drove a 2006 Optima yesterday with 123k miles, considering if I want to purchase. I did hear some grinding noise, front right. Brake pads were new, but rotor looks worn slightly. With experience from another car, I believe it could be the bearing. Your video has been the best video on how to change the bearing I've ever seen!! Excellent POV and talking through the process. I will subscribe to your channel.
I was going to pound out one broken stud , where a portion of the dust shield is cut. Now I see I can do the hub, which I have seen over-complicated videos posted. This video takes the reluctance to tackle this away. Thanks
I like the video most people have told me they have to be pressed on and off for the bearing
Great video bro, I can now help my daughter out with her 2015 Kia Optima. She needs 2 wheel studs replaced and this video showed me how to just replace the whole assembly. Thank you so much.
How did you make out? My daughter has a 2015 as well, broken wheel studs on front.
Hi friend. what a great video. I am a visitor from Mexico. I thank you for the video now I know how to do the procedure to change those hubs and the cv axles, I have to do complete maintenance on the front suspension and I have a buzzing noise in the hubs so I will change them. Greetings again and you have a follower from Mexico.
That was great. Thank you. I do a lot of my own work anyway and am contemplating doing it myself. Your vid really helped.
2013 Hyundai Sonata doesn’t have a unitized hub assembly as in this video. Mine has the hub bearing press fit in the steering knuckle and the hub press fit through the bearing which equates to more work. Great video though but I do believe different model years were equipped differently. 😉
Did you end up doing this job on your own? Went to parts store and Kia dealer and bearing has to be pressed in which I was about to do until the guy told me the tool was $170.
What you can do is buy the new bearings and take off the old one and take it to a shop that can press in and out the bearings that way they can't charge you too much because they didn't take off the parts
@@DULLAHGOSOHARD or if you’re mechanically inclined for to harbor freight buy a fwd bearing puller. You still need a puller to pull the hub shaft out the bearing. Then you have to cut the inner race off the hub shaft. So if it’s a one time thing go to a shop. If you doing it all the time well then I’d equip myself with the necessary tools to be speedy and quality savvy. Honestly if you’re here asking all these questions I’d just take it to a shop.
This worked perfectly for my 2015 Hyundai i40 (same part). Only difference is mine was no where near as clean and had to be beaten repeatedly with a hammer before it came out!
I think you should always test to see if the new part will not give any sound before assembling. Like turning and listening for usual noise
Seems like they have changed things on 18’ Optima, the bolts holding my caliper are all 14 mm instead of 17 mm.
Sob, newer version has bolt on bearings? I have the press in. (Really only watching to see if i gotta buy a new wheel hub or not, dont feel like messing with the brace though im fully capable of removing it if i take it to work 😂......im lazy)
thanks man really appreciate this video
Hey I have a Kia Optima 2013 I broke the lock supporter I’m having hard time to find another one what should I do ?
Thanks for the video.
Respect yaad man. Which part inna the world yuh did deh when u did a do this? 🇯🇲🇯🇲🇯🇲
Florida
Thanks Much!
You left the bungie cord on the car when you put the wheel on...Did you ever find it?
Lol i took off when i double check my work after i put the wheel on
Hey man u can show me where place for abs drive side
What year is this car? My 2013 Optima is nothing like that.
Should i try fixing mine too?
Good work! Is it the same for 2013 Kia Optima? I’m having trouble finding front hub assembly for it.
They just start using the hub assembly like that back on earlier models have to press in the bearings
Dullah Goso hard thanks brother
Would this make the tire smoke? And make metal/metal noises?
Yes
Can you help me find one for my 2015 kia optima lx
Where you located at
@@DULLAHGOSOHARD orange county ca
@@0032richie am in Florida
@@DULLAHGOSOHARD the part you listed is for the rear and not my year
Is it pretty similar to a rear wheel bearing replacement?
Am not sure
Veloster same way?
How long does this take on Kia Optima 2013 LX having someone telling me 3 hrs of work just curious
Depends on the skill level of the person that doing it but it should be less than 3 hours
Ok thanks
Is it the same as 2013 optima or no ?
@@amjadking879 nope, my 2013 kia optima sx turbo has completely different setup. Wish it was this easy
What year is that?
2017 and up
This does not work for 2013 model kia optima!
Not its for the newer ones
hard you should specifically say what models its for
2010-13 have a knuckle that needs to be removed from the car, a big bearing is pressed out the back and a new bearing is pressed back in.
I just bought new loaded left and right steering knuckle assembly from Canada. I have a 2013 kia optima sx turbo corsa blue loaded off the showroom floor. 131k on the car. Kia replaced my engine free of charge after major engine failure 4k ago. Just did the first oil change the other day. Drove to Colorado and back home on a quick trip. I bought the set I got because it has everything all pre loaded. The sx turbo in the first 5 months of 2013 is completely different with soo many weird parts. I've kept this car going after all these years. She gets down. Wish I could replace the hub/bearing assembly on my kia this easy but nope. It's all good. The new setup looks alot stronger!
Mine not like that and it a 2015
Car looks very new, and already had a wheel bearing failure? Thanks but no thanks Kia/Hyundai..
So true I have a Kia optima had to change steering knuckle rack an pinion and both front wheel bearing hub under 35,000 miles
@@abzalmohammed1184 where is the steering knuckle? Rack and pinion? Is that the full steering rack. My car feels like it’s all over the road. One minute it’s fine.
My 09 sonata hub doesn't look like that 😡
No you have to press in and out that bearings
@@DULLAHGOSOHARD that's what I hate
@@youngbeezygaming me too
If I remove a hub off a car at the junk yard will the wheel bearing be already inside?
@@youngbeezygaming yes that's a good way to avoid pushing in and out the bearings