Install Ace V5 chip (2nd trinity) XBOX 360 RGH
HTML-код
- Опубликовано: 20 авг 2024
- Fast forwarded video of ACE V5 installation on trinity motherboard.
Electric connections;
x360ace.com/V5/
team-xecuter.c...
RGH is same as other methods;
1) soldering
2) connect xbox to power (don't turn on power!!!), connect J-r programmer and read NAND.
3) write ecc
4) startup and get cpu code
5) write xebuild image with cpu code
6) write image to NAND
7) Have fun
If C1 and C2 connection points aren't clear, check out my quick paint drawing to clarify;
drive.google.c...
- C1 Has 2 solder options as indicated (blue)
- C2 Has 2 solder options as indicated (orange)
- Solder points are connected with trace in PCB (purple)
Hey man thanks for the video, this helped me get my 360 hacked. There's lots of guides out but it's not the same as a video.
Those C1 & C2 points are pretty tricky. Gotta be careful or you could accidentally lift one of those SMD components off of the board!
The ace v5 worked great for me on my Trinity board, thanks for the video
Cool man, nice to see it helped
Esse sim é um tutorial na intenção de ensinar, pois vi muitos tutoriais no RUclips que eles fazem toda a instalação nos pontos de solda, mais não mostram imagens proximas mostrando esses pontos.
Parabéns amigo esse foi o melhor tutorial que encontrei aqui no RUclips 👏👏👏👏
Did you program the ace v5 for the trinity or it comes already programmed from aliexpress? And just ready to install on a trinity board.
Ace V5 can't be programmed. It has a built in program. The Ace V3 can be programmed. No matter where you buy your V5 from, it's always preprogrammed.
@@Dave407Disabeld thanks man, gonna buy one for my trinity. Hope it works fine.
thank you. did you program the v5 chip or did you left it in stock when you boot it.
trinitys have to be programmed for ace v5. if its a corona though, its usually good to go out the box so to speak :)
You can't program the ace v5 from what i understand. The video shows the complete process of rgh'ing the xbox
Just install V5 on my friend xbox, just short P1joint without flashing the chip (stock firmware) and it has perfect starts. Better than my old xbox with x360run.
Does the cr4 speed up work? Also, is the P2 method better? I used the p1 and it boots fine, sometimes it can take longer so I'd like to speed it up a little
@@nateg7835 the P2 and P1 method are for different xbox motherboards. It probably doesn't work if you mix them up. I didn't try cr4 speedup. Doubt it would work anyway.
hey which side do i put the c1 and 2 soldier?
Not so good glitch timings. I got insta boot with acev3 on my trinitys, sometimes two cicles. Whats is the diference betwen this chips?
I'm honestly very happy about them. Max 3. Usually one or two. The cr4 I got for a corona takes ages. I've got 3 trinity like this and they work consistently good like this. I use them for lan parties
The pictures are confusing. Do you solder the wire in between the C1 and C2 or is one end of them?
C1 can be connected to the left or right resistor. If you look close you'll see it doesn't matter which one you pick because there's a trace connecting them together. Same goes for C2
I solder one to the middle left and the other to the middle right so I have more place for the wires and soldering
I soldered C1 to the right side of the left resistor and C2 to the left side of the right resistor. (17:10 in the video).
@@Dave407Disabeld So does that mean if I bridge the resistors it will still work?
@@ngceborichardmthembu2135 if you want, use a multimeter to check. But you can see the trace on the pcb connecting them together
What can I do when i accidentally removed the SMCs on c1,c2?😭
Can't you put them back? Use some tweezers to hold them in place and solder them back on? Or did you break the pad?
You can post a picture and comments on reddit in r/360hacks, i'm sure it's easier to see whats going on with some pictures
14:48 you turn off the Xbox? After the xell?
I take a picture of the cpu key in xell on the tv. Then i turn the xbox off and put it next to my computer with the jrunner connected. At that point i can write the cpu key on my nand backup. This cpu key then allows me to
For c1 and 2 do you connect them with solder
Yeah, just a little. I put tin on the wire and use that to connect it. No need for extra.
How you get cpu key???
At 14:44 i am booting up xell. Read the code from there. Take a picture for example.
Too fast 👎🏻