thanks, i got basic 24L compressor, here are it's info: Power: 1.5 kW/2 HP rpm: 2850 U/min max flow: 206 l/min max preassure: 8 bar tanks: 24 l and while working it run about every 5 minutes depend on setted preassure of airassist
@@huseyinpolat9981 it doesn't fit on neje 4 true, because it's prepared to install L profiles on each thread it got on L profiles, but can do also with honeycomb, i just put few plates of 5mm plywood under, so the honeycomb panel fit over the front and back L profiles and that's it.
Given the cost of this panel, it might be cheaper just to buy aluminum honeycomb, was the steel panel better output than the aluminium honeycomb. Q. Have you tried the E40 module?
i think aluminium one work exact same as steel one, pros of aluminium one is that it can't rust, cons is that it's quite delicate and can be demaged quicly, steel one is very tough and magnets can be used to hold the material. defenitley aluminium honeycomb will be cheaper, but don't know where to get one, plus they may be some problem of banding, mine aluminium (small round one) is always a bit bendet on one or another side, if plate will be bigger also that issue will be bigger i think. i got E80 at home but didn't test yet, hope to get time to make a test soon.
@@skylarshockman7659 no i think it's not yet realeased by neje, i edit E40 video right now, but it is not that good as A40640 wich cut about 20mm E40 only about 15mm
![Neje E40 Laser modul [unbox/review/first test] + compare with a40640](http://i.ytimg.com/vi/AFZtMHHA9Bw/mqdefault.jpg)
![Noob To Max With DRAGON REWORK In Blox Fruits [FULL MOVIE]](http://i.ytimg.com/vi/LnBMOinoOvA/mqdefault.jpg)
With a great panel comes great price ;)
It matches perfectly to the Neje 3 Max
exactly, good product with lot of materiall can't be cheap, another + is that it fit right into neje max ;)
Great videos, Thanks. Hi can you please tell me how many litres per minute does your air pump put out.
thanks, i got basic 24L compressor, here are it's info:
Power: 1.5 kW/2 HP
rpm: 2850 U/min
max flow: 206 l/min
max preassure: 8 bar
tanks: 24 l
and while working it run about every 5 minutes depend on setted preassure of airassist
Great video, what is the name of the 1mm thick material you used as desk protection?
Basic inox sheet, you can buy metal it's much cheaper, 0,5mm will be enough.
@@TinC33 Thank you.
hello, I just received the lower honeycomb, but it did not fit. am I doing wrong. I would be glad if you help. Thanks
what model of engraver you got?
@@TinC33 neje Max 4
Can you help me with the installation, my friend, how do we cut. How do we communicate? thanks❤
@@huseyinpolat9981 it doesn't fit on neje 4 true, because it's prepared to install L profiles on each thread it got on L profiles, but can do also with honeycomb, i just put few plates of 5mm plywood under, so the honeycomb panel fit over the front and back L profiles and that's it.
@@TinC33 62 / 5.000
Çeviri sonuçları
Çeviri sonucu
star_border
I understand. can you help me with neje 4 machine working
3:41 😁😁😁 "... piece of sheet"
Given the cost of this panel, it might be cheaper just to buy aluminum honeycomb, was the steel panel better output than the aluminium honeycomb. Q. Have you tried the E40 module?
i think aluminium one work exact same as steel one, pros of aluminium one is that it can't rust, cons is that it's quite delicate and can be demaged quicly, steel one is very tough and magnets can be used to hold the material. defenitley aluminium honeycomb will be cheaper, but don't know where to get one, plus they may be some problem of banding, mine aluminium (small round one) is always a bit bendet on one or another side, if plate will be bigger also that issue will be bigger i think.
i got E80 at home but didn't test yet, hope to get time to make a test soon.
@@TinC33 how do you have and e80?
@@skylarshockman7659 no i think it's not yet realeased by neje, i edit E40 video right now, but it is not that good as A40640 wich cut about 20mm E40 only about 15mm
big one , love it 😀