HOW TO REMOVE AND INSTALL POWER STEERING PULLEY | Dodge Caravan
HTML-код
- Опубликовано: 17 окт 2024
- Complete step by step pulley replacement tutorial: HOW TO REMOVE AND INSTALL POWER STEERING PULLEY. Pulley Replacement Made Easy. Most of the pulleys can be replaced by using this technique easy and safe. As example we replaced pulley on 2004 Dodge Grand Caravan.
Dodge Caravan: How To Replace Power Steering Pump, High Pressure Line and Reservoir 3 in 1
• Dodge Caravan: How To ...
#PistonSHACK #powersteering #DodgeCaravan
DISCLAIMER: Due to factors beyond the control of PISTONSHACK, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. PISTONSHACK assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. PISTONSHACK recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of PISTONSHACK, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not PISTONSHACK.
Thank you brother
Any time!
Thank you
You bet!
Beautiful Teaching Sir!
Glad you think so!
Where can you get those pulls from
Hi! Thank you for everything!!! Wow! How do I remove Power Steering Pump, ‘96 Mits L-400 petrol? And I can’t seem to find replacement… help?😊
Hi, Michael. Unfortunately, I don't have Mitsubishi 6G72 gasoline engine to show you in details. Are you in Canada or US?
Hi! US… I think I can figure it out, just need a lil direction and motivation I guess.. I can’t seem to figure out how to loosen the belt and pulley wheel to begin taking the pump off.. 🚐
I have a 2010 dodge caravan ,how do you stop the pulley from spinning when you tighten down the installers bolt. Is there a tool that attaches to the pulley to hold it ?
Hey Lynn. If pulley spins at the beginning, just hold it by hand then when pulley started installer screw will drive it down.
thank you for your advice. But the force I have put on the wrench to rachet down the installers nut feels like the instsllers bolt will break,I also have the pwr steering pump in a vice and have put a screw driver through on of the plastis holes iin the pulley and also that same screw driver that is wedged against the plastic pulley is also against the pwr steering housing . Iam also worried it might crack that as well. I also lubed up both the inside ring of pulley and shaft of pwr steering pump,they are both brand new. It looks so easy on u tube with people just holding the pulley in one hand lol! Thanks again for your coment,as this is a nightmare lol!
I would measure diameter of the new pump - pulley and old ones to see what tolerances are. Might try old pulley on new pump to see how that one goes.
thank you for the advice again. I bought 2 different pulley pullers as I couldnt get the old pulley off all that the pullers did was break off bits of the rim that the clam uses to pull off the pulley which never happened. So I gave up and bought a new dealer pulley to match the new pump,I should have mention I got the new pulley halve pressed down which was a struggle and just have about 7 turns left to its seated in the correct postion,but just cant get it to budge. So Iam off to pour a good strong drink lol! yikes!
Very interesting! Thanks for showing
You are very welcome! Thanks for watching) Cheers!
excellent vid homie
Thanks Brandon!
Straight and to the point! 👍
Thanks for your feedback Sean!
Thanks harbor freight has kit for $20
That's awesome Brian! I got mine for 20$ as well.