Nice program sir. Ye kitane v pe chalega. Aur ispar aahe matlab 1 no led ki line main aur balb laga sakate hai kya. Vaise hi 1 to 10 main lagake laiting tayyar kar sakate hai kya.
Muito bom , porem poderia colocar uma folha em baixo para focar melhor a visualização porque a folha q já estava riscada estava confundindo o desenho poderia estar melhor .......será que da para acelerar o piscar dos Leds ?
cool ... do you know how to make an audio player for USB? I already tried to make one, but I still have not found the integrated circuit used to play songs from a USB stick!
Hello, i enjoy watching tour vídeos thanks. I would like ti know where do you buy the components? If you are cable to tell me thank you. Pardon muy english is not that great.
The background music can explane everything to you... Volt, plority for led and what name for the jumper wire.. If i'am a new students and don't know the basic in electronics maybe can explod the IC.. If students know the basic in electronics maybe 70% can finish the project other 30% short circuit..
Search by the 4017 datasheet... pdf1.alldatasheet.com/datasheet-pdf/view/50846/FAIRCHILD/CD4017.html This CI uses from 3 to 15 V... and using Ohm Law you can find the voltage by yourself... look at the resistor value... A Led consumes about 20mA, so... U = R.I U = 470 * 0.02 U = 9.4 9 V is Ok, I guess...
@@steveogden8787 Thank you for replying. You're right. It must be RGB and I tried normal Led which doesn't work. I just bought RGB Led and tried it. There is one tiny problem. Once the last led light, instead of starting again from the 1st led immediately all the leds light up altogether before that. just like this video -> --ruclips.net/video/SVIU7ZhE9jQ-/видео.html- look at time --3:55- 4:00 It doesn't shift properly. I don't know why the owner of this video able to do without this problem. Anyway, I just tried the same setup and connect to 555 timer instead of flashing RGB and it looked better.
@@jumbo999614 I built this circuit on a perf board (ruclips.net/video/kquniJX8tws/видео.html) and it works perfectly with the blinking 5mm red LED. It has been running for 48 hours without any issues.
no only 1 at a time (out of 10) and one Pin should not deliver more than 10-20mA ... so use a transistor to drive more leds at one pin at the same time
Tell me, I thought americans always measure in inches. When you made the holes for the leds you used the cm scale instead. Is this common or is it easier? By the way, great suggestion.
Because of the way this guy writes his 7's, I don't think he is American. Regardless of that, most rulers sold in the states have both scales on them. Many tape measures also have both. Science and technology classes use metric, so students of those courses become familiar with the metric system. People that know both, know that when dividing a length into equal segments, metric is far easier to use than inches. Decimals and base 10 are easier and faster to use with a calculator than fractions and base 12. Here in the states, laymen, carpenters, woodworkers, surveyors, plumbers, and others in similar professions, tend to use inches. Most trained technicians, regardless of the field, and scientist types, regularly use metrics. I have been fluent in both for about 35 years. I find that I tend to choose which system I use is based on the task I'm doing.
He turn to orientate if you look there is a flag like in diode (anode) have flat spot on base. they WILL not work backwards....can't get any simpler than that... wanna go faster that is in the resister... I believe he used a 470 go 380 and lower or throw a 10k pot into the mix. There that's my contribution
The LED that connects pin 14 with 16 MUST be of the flashing RGB (red, green, blue) kind. They have the usual 2 pins. I got mine from Amazon.
Thanks for posting that bit of left out information! The circuit will absolutely not work with a standard 5mm LED.
Thank you. You have helped me through the first step of my journey through electrical engineering.
Спасибо! Интересная конструкция! Отличная идея и способ навесного изготовления! Very good! ;)
Sir. ..aapne....test kisse check kiya h. ..battery se. ...ya....220V supply se....please reply me
Nice program sir.
Ye kitane v pe chalega.
Aur ispar aahe matlab 1 no led ki line main aur balb laga sakate hai kya. Vaise hi 1 to 10 main lagake laiting tayyar kar sakate hai kya.
Nice job! Very simple easy..!
Are you using a rgb led for the red light or there is a delay timer inside the ic
What about an explanation of the the switching mechanism if clock seems to be continuosly high?
Muito legal. ( Quais os cis que substitui esse ic 4017 para esse mesmo projeto ?)
Mau tanya pak tahanan 470 nyambunya kemana satu ke bag. Neg. Tp satu lagi ke led yg mana ya
Excelente, gracias. Saludos desde 🇻🇪
Muito bom , porem poderia colocar uma folha em baixo para focar melhor a visualização porque a folha q já estava riscada estava confundindo o desenho poderia estar melhor .......será que da para acelerar o piscar dos Leds ?
Great
Thanks for your
Sharing is very helpful
Ring ic is used or Johnson model .?
Plz show different model blinking IC video plz upload 🔌💡
How do you speed it up. I need it to do all 10 in .1 seconds. Thanks for the simple video!
i have
use resistors of higher value
Input voltage ?
Tem como substituir o LED pôr relé de 3v?
Very Nice Sir... Thanks for your video n peace from Indonesia
Hello friend, spectacular! How many volts do you apply? Regards :)
3 to 15 vcc
Most straight forward tutorial Ive seen, awesome well done 😊
Nice, Can I use normally open relay to drive more LEDs? Thanks Agree with Bharat...Change Background Sound LOL
:) :) :)
Yes
Why use a relay, a transistor will do the same job.
Great !! But change background music please !
Music se lag raha hai koi mar gaya hai...
12 volt car ki battery se on Hoga?
Is cheaser te main led light laga sakda ha. Please tell me.
I need 12-13V and more fast circuit?
What components attach to do fast run plz show reply
抵抗の所、可変抵抗でも出来るんですか？
cool ... do you know how to make an audio player for USB? I already tried to make one, but I still have not found the integrated circuit used to play songs from a USB stick!
Sir process se Ac bulbs jala sakte hain
Speed karane ke liye kya karege
Mooi stukje soldeerwerk,had leuk gevonden de maten van het draad had vermeld
Input voltage sir?
Mujhe LED ki jagah relay lagani hai tu kam karegi kya
Output not coming only one light only glowing is there any fault..?
Yes there is a ckt missing use 555 ic in astable mode...
I think u should use flasher led rather than a common red led for pulse trigger.
Muito bom vou tentar fazer obrigado pela ajuda
how many volt suplay it
Could you tell How to connect more dhan 10 LEDs...like 15 LEDs in one transistor can we make it or impossible?
Can we make it blink faster?
Isaka input kya hai ac ya dc
Oscilador????
led flash
Sir led kitne volt ki he bolo
good work man
Hello, i enjoy watching tour vídeos thanks. I would like ti know where do you buy the components? If you are cable to tell me thank you. Pardon muy english is not that great.
Excellent 👌👌
can i use battery 9v ?
How we extend for more led like 100 .very simle way to teach us. Thanks
The background music can explane everything to you... Volt, plority for led and what name for the jumper wire.. If i'am a new students and don't know the basic in electronics maybe can explod the IC.. If students know the basic in electronics maybe 70% can finish the project other 30% short circuit..
Hi..
How can i make it blink faster ?
is it possible?
Faster blinking led, or really anything that can interrupt current between pin 14 and 16 while circuit is on.
I have been studying the datashhet .👍😆
Thank you fot the hint.
100 Led ke liye chalega kya aiae
Sorry sir, I'm a beginner... I want to ask... how many volts does it use... thanks all
that red LED is blinking LED
With out ic555 it won't work or give blinking effect or else using blinking LED
How to make 3channel remort controller system circuit???????
The speed is slow, how to increase the speed of chasing?
Please tell me,how many led lights i can use?
Great but how do increase speed. .
Yes, I'd like to know if that's possible too
Input kitna volts diya bhai
Speed control?
How power volt???
yes i'm too want know
Please tell me the number of the ragistrech
Does anyone know what voltage this is using? I would assume 5, though I dislike making assumptions.
Because of the resister for the leds I would say that too.
भैया एसीआईसी किस बोर्ड में से मिल सकती है क्या
Voolt????
3 or 5 volts
Can 12v LED?
So nice thanks
its main supply is also blinking please check experts
You didn't show the power how much voltage and current you used? I see ( + , -- ) only!
Search by the 4017 datasheet... pdf1.alldatasheet.com/datasheet-pdf/view/50846/FAIRCHILD/CD4017.html
This CI uses from 3 to 15 V...
and using Ohm Law you can find the voltage by yourself... look at the resistor value...
A Led consumes about 20mA, so...
U = R.I
U = 470 * 0.02
U = 9.4
9 V is Ok, I guess...
Your video is amazing but you do not link the materials
I tried this on a breadboard. It doesn't shift to the next output. Output is random.
Also the led on pin 16&14 doesn't blink.
The LED that connects pin 14 with 16 MUST be of the flashing RGB (red, green, blue) kind. They have the usual 2 pins. I got mine from Amazon.
@@steveogden8787 Thank you for replying. You're right. It must be RGB and I tried normal Led which doesn't work.
I just bought RGB Led and tried it. There is one tiny problem. Once the last led light, instead of starting again from the 1st led immediately all the leds light up altogether before that.
just like this video -> --ruclips.net/video/SVIU7ZhE9jQ-/видео.html- look at time --3:55- 4:00
It doesn't shift properly. I don't know why the owner of this video able to do without this problem.
Anyway, I just tried the same setup and connect to 555 timer instead of flashing RGB and it looked better.
@@jumbo999614 I built this circuit on a perf board (ruclips.net/video/kquniJX8tws/видео.html) and it works perfectly with the blinking 5mm red LED. It has been running for 48 hours without any issues.
Red led auto flip flap ?
Excellent job and tutorial! Thank you! I have ordered a load of 4017 chips in view of making lights for a homemade UFO. :)
no 555 timer ic?
Top👍saubere Arbeit. Auch verständlich zum nachbauen.😀
Sir, can we do 10 ( blinking ) led chaser with IC 4017?
no only 1 at a time (out of 10) and one Pin should not deliver more than 10-20mA ... so use a transistor to drive more leds at one pin at the same time
Thanks for ur great post. Awesome
I did the circuit but all the LEDs were working together
Why is that?
You mean all the leds light up at the same time right?
???? et a
quoi sa serre
Mujhe LED Ke Jigar relay Lagani hai Hi Tu relay LED ki Ki Tarah kaam karegi jawab jaldi den
Le hubiera quedado mas pulido hacer el circuito por medio de un plano impreso en una pcv para que el circuito que mas presentable y organizado
Osame dost
Please share component to component Soldering tips
sir speed tej kese kare
Mera e ckt keu Kam nehin Kar raha
Tq sir
Sir plz how to Chekiang load in DG & HT tell me sir
With some relays... dancing christmas lights 😁
Why we have to connect red LED is that must
Tell me, I thought americans always measure in inches. When you made the holes for the leds you used the cm scale instead. Is this common or is it easier? By the way, great suggestion.
Because of the way this guy writes his 7's, I don't think he is American. Regardless of that, most rulers sold in the states have both scales on them. Many tape measures also have both.
Science and technology classes use metric, so students of those courses become familiar with the metric system. People that know both, know that when dividing a length into equal segments, metric is far easier to use than inches. Decimals and base 10 are easier and faster to use with a calculator than fractions and base 12.
Here in the states, laymen, carpenters, woodworkers, surveyors, plumbers, and others in similar professions, tend to use inches. Most trained technicians, regardless of the field, and scientist types, regularly use metrics.
I have been fluent in both for about 35 years. I find that I tend to choose which system I use is based on the task I'm doing.
better you show, how to see whats " + and - " of leds. i see you turned some.
any chance of the diagram thanks
Nice sir
Very nice...
เจ้าของช่องเป็นคนไทยรึเปล่าครับ ผมดูมาหลายปีแล้ว อุปกรณ์แต่ละอย่างมันคุ้นตาซะเหลือเกิน ถ้าใช่กดไลค์ตอบกลับหน่อยนะครับ 555
Ap ka soldar karne ka tare ka pasand ayeya
هل تعمل عمليا هذه الدارة
светодиоды можно былобы припаять на выводах и без провода . и к микросхеме тоже .
Tuku e Nang ngendi
How to do fast blink
He turn to orientate if you look there is a flag like in diode (anode) have flat spot on base. they WILL not work backwards....can't get any simpler than that...
wanna go faster that is in the resister... I believe he used a 470 go 380 and lower or throw a 10k pot into the mix.
There that's my contribution
Same music on every video? So annoying.
Very intelligently
You can subscribe to my channel from your left
Return / When you sign up, write
How much the volt of the circuit
9v
@@CienciaemcasaBR thanks