Thanks for watching & we really appreciate you sharing your kind words. Great to hear the video helped. Let us know if you have any questions Terence, us fellow DIY’ers need to stick together! Hope all is well with you and your family.
Spicly123 Thank you and that’s very nice of you. We really appreciate your comment and we are always here to help answer questions. Please subscribe to the channel and ring your RUclips bell 🔔 this will be very helpful to us thanks again. 😎👍🔧🔩
@@DIYwithMichaelBorders flashed. The flash light its still on, but can I ask you what you believe the problem might be? I tried again to flash the big lights it happened again, ABS flashed and car reduced speed.. I would appreciate if you can give me your advice
CancelIKL Thanks for watching, this usually happens when there is an electrical short. We recommend inspecting all wiring for any loose connections. A slightly loose wire can lead to your exact issue. 😎👍🔧🔩
Magnificent video and magnificent edition; Thank you for bringing to light an issue that for me was unknown, till today that the Light of the ABS was set on my car's dashboard. Blessings 🙏
Good morning. ☕️ Great to hear our video was helpful, and you are very welcome. Thank you for being kind enough to share this comment. Hope you have a great weekend. 😎👍
Good morning Ray, thank you for this. We do our best to give the DIY community all the help we can, many more helpful videos to come! Welcome to the DIY Raptor Club.
Thank you so much. This is my current situation with my Chevy Equinox 2016 that happened today. I panicked and rushed to a local repair shop for a diagnostic and got a quote for $800 to replace the ABS module 🥲🥲. My heart dropped from that shocker. So I resorted to Googling the issue and your RUclips video popped up for the reset trick so I will definitely try that in the morning. If not, I will refer back to this specific video for additional help. Thank you tons. I will post an updated comment if all is successful either way.🙏🏾
You are very welcome, $800 is a chunk of money that you can hopefully keep in your pocket and spend on something more meaningful. Keep us posted and hey if you’re into crypto trading, check out our newly launched DIY ecosystem. Toolboxtoken.com Reach out to us any time! 🧰
Overall good video, only one point that I have issue with. The two block fuses are not dealer only and can be purchased at most parts stores and even most Wal-Marts in the automotive section.
ESPECIALLY APPRECIATE YOUR TEACHING SAFETY TIPS !! YOUR ONE OF THE FEW WHO TAKES SAFETY FIRST !! THANK YOU FOR THE TUTORIAL !! EASY CLEAR VIEW VIDEO AND LISTENING !!
Thanks for watching & welcome to the DIY Raptor Club. Safety is very important & we appreciate you reaching out to us. Let us know if you have any questions. Enjoy your day.
Great presentation. The control circuits on these ABS systems are typically low voltage, low amperage, which means you need to check the ABS Module grounds after you check the fuses, or check the separate voltage values either at the wheels yourself, or the voltages coming into the ABS module while a second person helps you by spinning each separate wheel one-at-a-time, but at a uniform rate. As I understand these systems, the interaction between magnetic part of the sensor assembly and the notches in the rotating wheel on the hub assembly generates the voltage measured as the wheel turns. Trucks are usually exposed to harsher conditions than cars, and exposure of the wheel sensors and connectors to water, sea water at the beach, salted roads, etc. over the years can result in degraded sensors at the wheels, or poor or corroded grounds or bad connections where the system wires connect to the push-on or screw-on connectors. Any of these issues can cause voltage variations that prevent the ABS system from knowing whether or not all 4 wheels are rotating at substantially the same speed, and if the signals aren't the same, the ABS light comes on. The profit margin between replacing the ABS Module and the sensors and sensor wiring on 4 wheels and bleeding or replacing the brake fluid is about $1,000 to 1,500 more than doing the checks he recommended, plus checking the grounds. The ABS module can be replaced with a new one, if necessary, without replacing the valves it is attached to, but it is likely it will have to be re-programmed for your specific vehicle. Programming Specs are often available online, but require special equipment. The alternative is sending a defective ABS module to a specialty shop which can repair the old one, and do any required programming. Costs vary, but usually much cheaper than having a new one programmed and installed - unless you have a shop that does this locally, it can take about ten days to send it and get it back, due to shipping times. P.S. The white illuminated board you have behind you in your videos is interesting, but it leaves your face in the shadows. Viewers like to see faces; something for you to consider.
We appreciate you sharing your thoughts and info. Always welcome here and much appreciated. We have improved our intros since this series. If you have time, hopefully you will visit our channel. Hope you’re having a great weekend. 😎👍
Thanks for the excellent video. And I appreciate it when you guys tell us girls who can help out with free services like OBD scanner checks. Very cool.
Both my daughters do all their own maintenance and repairs on their vehicles. They grew up helping me in my shop and learned not only how to do a lot of jobs but how to do so safely.
2009 Dodge caliber 2.0 ABS light came on. Lifted front end up and ran it to 50 mph and listened for bad bearing. Sounded fine both sides. Checked each back tire and turned by hand and all seemed fine for noise. Grabbed each tire and wiggled and evrything seems tight. Asked my son about the tire pressure and found that all the tires were at 25 to 27 psi. Filled all tires to 33 psi and we took it for a run. Guess what the abs light went out. Completely surprised me. Check your air pressure of the tires first. It was a very simple fix............................................
Thanks for watching & we really appreciate you sharing this. That can definitely do it. This is great advice. Welcome to the DIY Raptor Club. Us fellow DIY’ers need to stick together. 😎👍🔧🔩
Ahmad Kamali You’re too kind & we appreciate that. We DIY’ers need to stick together & help each other. 😀 We have several more videos regarding that annoying ABS light on vehicle dashboard’s...the ABS light has unfortunately become an annoying nightmare for many drivers. 😎👍🔧🔩
Thanks for the info education on abs symptoms and possible causes creating abs light on dash. I'm trying to determine if the mechanic that told me my abs pump is failing is correct or not where as they said my coolant leak was coming from heater coil gear assembly but wasn't case and I paid $500 for that to be replaced and installed then that evening my abs light came on. I've bn spending money on repairing front suspension system. Have yet to replace engine mounts, brakes, and rear suspension as well as tires brakes and then eventually replace interior seating, steering wheel and center console gear shifter and compartment ..
Good morning, you are very welcome. ABS pump failure is not uncommon however if vehicle is less than 10 years old…it’s unlikely that the pump has failed. It may be as simple as a speed sensor however without hooking up OBD2 scanner, we can’t confidently say. Having a scanner will help pinpoint the exact part causing your issue.
I have a 2011 Dodge Ram 1500, 3.7 Engine V6 w/only 74,000 miles bought it brand new. About 16 months ago, the ABS light came on the Dashboard, thought it was the rear sensors, I changed out both, but the ABS Light did not go out. So I took it to back to the Dealer where I had bought the truck way back then. So the issue was the ABS Modulator, had it replace cost about $1,800.00 Drove really good for about 18 months, and last month the ABS Light came back on again, now I am not a mechanic, and am not mechanically incline. Just a few basics, I went to several shops, they all told me the same thing, ABS Modulator w/code C-1073, again it was the ABS Modulator. Finally took back my truck to the Dealers, they said, ABS Modulators are no long made, but they are Re-manufactured, in other words rebuilt w/a 6 month Guarantee . So I paid about $800, and the Re-built ABS Modulator was installed and Re-program. All is well, but what I want to say is, I am keeping this truck till one of us goes up into the sky, either me or the truck. So this time that I had another ABS Modulator installed, I told the Dealership I wanted the ABS Modulator that was on the truck to be given back to me. And I got it back, and am sending it off to have it repaired. I will tell you why, because it is ALL READY PROGRAM for My Truck. The Cost to Re-built the ABS Modulator is only about $300 total, but those that are sold, are not Programed for the car or truck it is going in too. That's why Companies ask you for a Vin Number when inquiring for a ABS Modulator. Getting back the ABS Modulator may save me money down the line, but it is the Programing for my own truck that is most important to me.. So am back on the road, and Merry Christmas to all.
@@PaulGuerrero-d8o Good morning ☕️ Thanks for taking the time to share your experience. That’s a great idea asking for your Modulator back. Getting it rebuilt and also having it already programmed for your exact truck is “money in the bank”. Sounds like you take great care of your 2011 Ram, and that goes a long way in keeping the vehicle reliable and on the road. Reach out to us any time. Many more helpful videos to come. 🧰
Loved the video. Just trying to find ways to check my abs on our Chevy Colorado 2012 ABS system before taking it to a mechanic. Thanks much --great advice on what to check on. Will try what I can.
Thanks for watching & sharing this, that’s very kind of you to take the time to reach out to us. Let us know if you have any questions, us DIYers need to stick together! 😎👍
Thank you, thank you and thank you for making the comments on having a secondary support for a jacked up vehicle. I see so many vids of people working under a vehicle with only one hydraulic support. Especially do not trust a hydraulic jack. My engineer dad and military training drilled this into me for years. It is a golden rule of working on heavy items. A set of jack stands is a cheap safegaurd and way cheaper than a hospital visit or a funeral.The video content on the troubleshooting was great.
David Crews Thanks for watching & sharing your thoughts David. We couldn’t agree with you more. Safety Safety Safety! 😀 We appreciate you reaching out to us. Us fellow DIY’ers need to stick together! 😎👍🔧🔩
Absolutely, just another useless invention to screw money out of us. Abs light can come on but there's nothing wrong with wheel rotation, it's all down to a damaged or failed senser or it's associated parts.
Yep. I’m 18 my car’s ABS has been out for three months now, best believe I’m not buying a new abs motor/pump for $200 if you can drive with it you can drive without it
Just installed the wrong bearing on a 2003 element awd and it has abs now I have the abs light on but even before that I had it on, and before that I was borrowing my brother's 1976 vw bug...we definitely don't need abs we need people being are of how to drive the car properly. I've seen people with abs hydroplane or crash even with the abs engaged. Abs doesn't fix idiots
Great video. Very clear and concise. I have a 2009 F 250 and my ABS light comes on intermittently. There doesn’t seem to be any pattern to it. The brakes are working fine without the ABS. I bought a Blue driver scanner and I’m getting code C1096 Pump Motor Open Circuit. I’m going to dive in on this next week, but was wondering if because it is intermittent, do you have any insights?
Thanks for watching & welcome to the DIY Raptor Club. Let’s try something. We recommend filling all four of your tires back up to its proper psi. See if this registers & runs off ABS light. Keep us posted. Enjoy your night! 😎👍🔧🔩
Question. My 1992 LT1 Corvette , has a problem. For the life of me I cannot spin or smoke my tires. The emergency brake warning light is always on. So I checked The brake fluid which is full,I changed all four of the brake pads on the entire car and the light is still on I also checked the wheel sensors some of them had rust buildup on them but I cleaned them going back in so why the hell cant I spend the tires on a Corvette. What is the use of owning a Corvette if you can’t smoke the tires that’s my problem I’ve been building dragon jeans for my older cars but I can’t figure out the brake light is unbelievable but he’s got an idea what it is let me know because I don’t see nothing on RUclips about it I even called the dealership and they won’t tell me they want me to bring the car in to take my money that shit ain’t going to happen. When I bought this Corvette I didn’t even realize until I lifted the hood after I got home there’s a Optispark distributor what kind of crap is that what’s a matter with the old Style ones on top of the back of the engine.
Thanks for watching & welcome to the DIY Raptor Club. An OBD scanner can help pinpoint the exact part that is causing issues to your brake system. AutoZone will read your fault codes for 100% free.
2006 Toyota Highlander 3.3L gas. I'm having an ABS issue, which I was told by my mechanic, that the first step is to replace the abs module. I'm getting the following codes C1223, U0073, U0123, U0124, U0126, C0371, and C1281 I can't find anyone that will rebuild my abs module. I understand they are extremely expensive at the dealer and I believe they are discontinued. I thought about buying a used one, but I don't know where to get it reprogrammed. I heard the dealers don't reprogram them unless it's a new one. Does anyone know where I can get it rebuilt? Oh by the way, the issue that started all of this was the day after bought it. It drove fine at the dealership and the next day, i was on a busy road and all of a sudden it lost power while accelerating and I would have to push the accelerator down all the way just for it to move 10 mph. The abs lights came on and the traction control as well. I'd appreciate any advice. The shady dealership told me I had a 1 week/1000 mile warranty that if ANY THING went wrong that they'll fix it. I called them and they said to look at my paperwork that I bought it as is and they refused to help me in any way. I did take them to court and won. I received a full refund and I was able to keep the car for free, minus the $750 I had to pay an attorney.
Awesome information/tutorial, the only observation I want to make is that not all abs systems are the same there are different cars that have different abs systems.
Good morning, just poured a cup of coffee and am sitting down to answer any and all questions for the DIY community. We really appreciate you watching and sharing your thoughts. Any and all helpful info is greatly appreciated! Let us know if you have any questions and hey if you’re into crypto trading, join our DIY ecosystem. toolboxtoken.com Reach out to us any time! 🧰
Brilliant bit of information. I had a passenger front sensor come up so it was replaced and one 15 minutes later after leaving the garage the ABS came on again and now it says the driver side rear sensor needs replacing. Could that be possible ? Or could it be the fuse or abs module ? Thanks
PERFECT video! My Mitsubishi outlander 2010 is recently showing ABS light issue. It is coming on and off on the dashboard. When it is on, then ACS off light turns on. The car is running well so far, no brake issue whatsoever with ABS light on. I have driven 5K+ miles with ABS light on. I got P1773 and C2116 codes. How serious is that?
Hello & thanks for such great videos. I have a situation where my 2005 Colorado goes into "Reduced Power" and then shows the message "Traction Fault". Would you happen to know anything about this? I have gone to soo many places & dealers & they can't figure it out because they can't replicate the situation because it only happens randomly. So when it happens, I get stranded for a few minutes, I shut it off, wait a few minutes and then I'm able to get going again. Now the weirdest is that EVEY TIME this happens, my power locks stop working, so I have to disconnect the battery for a few minutes and everything works back to normal again.... any advise? It would be GREATLY APPRECIATED!!!!
Good morning, just poured a cup of coffee and am sitting down to answer any and all questions for the DIY community. It could be an electrical issue. You may have a loose connection…we recommend inspecting any and all electrical connections and fuses related to ABS system as well as the Traction Control system. You might even have a part in its early stages of failure…which because of this…the part itself is working intermittently. Please keep us posted. Make sure all tires are properly inflated to the manufacturer max recommended psi. Let us know if you have any questions and hey if you’re into crypto trading, join our DIY ecosystem. toolboxtoken.com Reach out to us any time! 🧰
@@DIYwithMichaelBorders Thank you very much for taking the time to respond. I will try your recommendations and keep you posted! I greatly appreciated!
@@dracony7649 Good morning ☕️ any update? It’s possible that the lighting for that indicator has burnt out however that is very uncommon and not likely the case. We recommend disconnecting the black negative cable from your battery and leaving disconnected for a minimum of five minutes. This will allow your system to perform a full electrical system reset. After five minutes, resecure black negative cable to battery and check electrical system by turning the key on, followed by starting the engine. This reset will hopefully remove any electrical glitches or malfunctions within the system and get your computer back to proper in normal configuration.
Hi, I would like to suggest another possible cause of ABS light on, brake light switch. At least it was true for my 95 GMC truck, after going through every possible cause without any result, by changing brake light switch it went away. In fact the faulty of my break light switch showed no problem with my actual brake lights, they worked fine, but it had caused ABS malfunctioning as well as problems with my ignition switch, control module and some other electrical problem as well. By changing that part, all my troubles got resolved, I thought it's worth mentioning my experience here.
Good morning ☕️ We are honored you took the time to share your experience and what solved issue for your GMC. Awesome job continuing your DIY project to diagnose the cause. Thanks again, much appreciated. 👍
I can't do a quick reset due to no key only a fob 2018 Jeep Cherokee codeU140A right front wheel speed sensor. It was your prior video of pumping the gas pedal then start?
Great video, I have a Ford explorer sport Trac 2008 and I recently replaced my tires of the vehicle and it recently started to turn on my abs light once I speed up to 15 mph, breaks work perfectly fine with no issue so I'm stumped as to why, I'm unsure if wheel unalignment may also have something to do with it.
Thanks for watching & welcome to the DIY Raptor Club. You mentioned you just recently replaced tires. Believe it or not, it may be as simple as bringing your air pressure inside your tire up to the recommended max psi. Please keep us posted.
Thanks for your knowledge of ABS. I recently replaced the two rear shocks of my 2012 escalade esv now the ABS, traction control, stabilitrak lights are on. The vehicle runs normal obd scanner shows no codes. Any clue? Thanks for responding.
Thanks for watching, it may be as simple as a quick reset. We recommend disconnecting the black negative cable from your battery and leaving disconnected for a minimum of five minutes…which will reset your computer. After five minutes, resecure black negative cable to battery and start engine.
@@DIYwithMichaelBorders hey thanks for the quick response. Still 3 lights showing after did what you suggested. I checked all tire pressures, wheel sensors wiring look fine. Basically the vehicle runs normal no limb mode. I'll just keep driving it maybe lights will turn off eventually.
@@chester3753 Thanks for the update? Did the battery connections feel loose…?…in other words, after you tighten 10mm nut to secure battery cable to terminal…can you move it easily or is it locked in-place? A loose connection can trigger miscellaneous errors such as ABS.
@@candlelightbeesgardening Absolutely! In addition, this time of year can cause havoc on a vehicles ABS system while driving in snow, ice, salt, slush, and dirt. However back to your question, dirt making it’s way onto, into, and around ABS components can definitely trigger the vehicle’s ABS light to illuminate. 😎☕️🧰
Hi, I own a Ford Escape 2009 2.5 engine FWD and appears the ABS and TCS light on. I scanned and shows the B2900 code, In my understanding it means that the ABS VIN module doesn't match with the mean computer. According to the shop it needs to reprogram but is too expensive. I have a basic scan and I can delete that code but when start again the vehicle appears again. So, the specific question, do exist any alternative method to correct o delete this? As a comment, I checked the 4 wheel sensors and looks good. Thank you from Chihuahua Mexico.
Thanks for watching Luis, you can start by a simple reset by disconnecting the battery for 30 minutes. It doesn’t work, module reprogram might be best.
This is very good tutorial on abs light on. My question is am rx 300,1999 model having same abs light on and speedometer not working what can I do pls but the transmission gear still working.
Thank you this very informative video ii do hope i can get some help with my question which is; my abs light stays off when i start the car with my foot on the break pedal but as soon as i release the pedal my abs light comes on. Help me please. Toyota 4runner 2000 limited 3.4L
Thanks for watching, this usually happens when the system detects low brake fluid. We recommend adding the proper brake fluid and bringing it back up to the proper fill parameters. In addition, there are a few video links below that you may find helpful. ruclips.net/video/5pwfHcBkvsU/видео.html ruclips.net/video/nQGf8rf4F5s/видео.html ruclips.net/video/CIRhyzDhqnE/видео.html 😎👍
I could argue there’s FAR more than 4 causes of an ABS malfunction. Caliper pistons, low brake fluid level/fluid leak, intermittent connectivity with either power or ground wires, low battery voltage, bent rims or fix-a-flat, the abs module might need re-calibration, bad MAF or MAP or crank or cam sensors….the list goes on and on and on…..it’s a sophisticated system.
Could you tell me why my ABS LIGHT CAME ON AFTER TAKING MY CAR IN FOR REPAIRS....THEY SAID THEY PUT ON A NEW SUPENSION RACK. PUT A FRONT GASKET ON......THEY ARGUE ITS MY WORD AGAINST THEIR MECHANIC.... MY LIGHT WASNT ON WHEN I TOOK IT IN
@@lajunecrockett2381 some ABS systems read sensors on the suspensions system as well. If that’s the case then every time the car is lifted off the ground the ABS light will turn on. Usually knowing which ABS code is causing the light to come on is the first step.
Greaat Great video........... I love youtube - SO educational. This Video was concise clear sooo helpful. Thank you to all you guys/gals for educating the rest of us.
Most fuse / relay blocks have a fuse pulling / insertion tool tucked away somewhere. Hard tools can easily break the fuse. But a great, easy video to follow. Thanks
Much easier to use needle nose pliers, very carefully as stated. Those little tools don't always work they great - especially in tight quarters. Use what works best for you.
I have an 07 Trailblazer and I replace my steering angle sensor and hub bearings with abs cord, brake rotors and pads, and abs light and traction control light still comes on, you have any idea? Thanks for sharing your video..
Thanks for watching & welcome to the DIY Raptor Club. You may need to perform an ABS system reset. Below is a link to our video showing this process. ruclips.net/video/Fu47rWAD30k/видео.html Please keep us posted. 😎👍🔧🔩
My 2008 has anti lock esp and slip lights come on when o go over 15 miles per hour. I have watch your videos on causes. How do I find out which wheel is making this happen? I noticed that I have a very slight vibration in my steering wheel could this mean I need to replace one of my rooters or the magnetic ring for my abs sensor Thank you for your videos and help
Thanks for reaching out to us Mark & we appreciate you watching our videos. Do you have an OBD scanner? If not, you come visit your local AutoZone and they can read your error codes for 100% free. The codes will help pinpoint the exact wheel hub causing issue. 😎👍🔧🔩
I have Ford Focus showing 2 ABS sensor errors. Testing the plugs, 2 are 12v, 2 are 9v. The wire from ABS module to sensors are in tact and i tested they carry 12v. So the ABS module is outputting 9v. Is it likely the electrics in the Module or something else? Maybe fuse box?
Hi! Thank you for taking the time to share your knowledge of vehicle repair with the world. My ABS light has been on (steady) since I had my tires replaced 3wks ago, getting ready for winter. For two days, the the ABS activates, showing a car skidding icon (on completely dry asphalt here) and the gas pedal loses pressure. It activates every time I have to start it up (minimum of 6x daily) and today it happened while I was facing oncoming traffic. Can you please tell me which of the 4 reasons explains the issue my 07' Lincoln Navigator L is having? Thanks a bunch!
Thanks for watching & welcome to the DIY Raptor Club. Let’s get this figured out. You mentioned tire service recently. Believe it or not, low tire pressure can trigger ABS light. We recommend checking the sidewall of your tire for the proper psi and filling your tires to that psi. Go for a test drive and see if this turns off your ABS. Keep us posted, us fellow DIY’ers need to stick together! 😎👍🔧🔩
I had a blow out on Tuesday. I ended up replacing all tires. I have the same issue that you described. The gas pedal acts up once when I start the vehicle, then it is OK the rest of the drive. Did you get it figured out?
@@BatmanVMMA Thanks for watching & it’s very possible that your blown tire damaged an ABS sensor. We recommend having your ABS error codes read by an OBD scanner. This will help us pinpoint the exact part causing your issue. AutoZone will read error codes for 100% free. 😎👍🔧🔩
@@BatmanVMMA please can you update this thread when you check the codes given. Currently in EXACTLY same situation. Blown tires > tires replaced > then ABS light.
@@charleseke7341 I used a code reader and there was a code. I think it was C0055 or something like that. The code reader told me the rear passenger tire speed sensor something something... I forgot exactly what it said, but I cleared it and it hasn't come back on. When I inspected the sensor, the blow out rubbed off some of the plastic coating on the wiring. I used some shrink wrap stuff on it. Hope this helps.
Thank you. Great video. My old honda odyssey recently showed an ABS light on along with other lights. After stopping at traffic light, my car won't accelerate when pressing the gas pedal. Do you think that would be the only problem? What would be the expected cost to repair each individual issue vs changing the whole ABS unit together? Here in CA prices can vary so much, price gouging is so common. I recently brought a 2013 escalade to the shop and they told me my rotor and axel in the back wheels have to be replaced, and I paid $6.5K for it. I am scared to bring my car to any mechanic worrying they are going to ask me to pay $2K for this issue.
Good morning, we are drinking our morning coffee answering any and all questions for the DIY community. You may actually have a caliper in its early stages of failure. If calipers have not been changed in last 5-7 years, it’s very likely the caliper is the cause. Please keep us posted, we DIYers need to stick together!
I had a ABS module replaced. They didn't use the scan tool to move valves in ABS module and properly get air out of lines when preforming brake bleed. So chased my tail figuring it out.
Great video. Is it possible for the ABS moduel to go bad and need to be replaced without the need to replace the speed sensors or the exciter magnetic rings?
@@DIYwithMichaelBorders.Mike Thanks for your reply. I need your help in understanding what is going on with my car and truly be thankful for your input. I have a 2012 Hundai Sonota. A few weeks ago Bunch of engin lights including ABS light (intermittently) were coming on. I took it to a Hundai dealer to have it checked. They told me this is electrical related issue and to diagnose the issue it will cost me $180. I agreed. After a few days their service called and said they have checked all the components that they thought could be causing this but haven't been able to pinpoint it and need to do further diagnostic work and it will cost me more money to do that. I agreed. After a few days they called and said they have determined the cause for this issue is a bad ABS moduel ...the cost will be 500 for diagnostic wk + $1300 to replace it. I agreed. I Had no other choice!! They called me yesterday and said they have installed the new ABS moduel and all engin lights except for the ABS is gone. They said that they have checked everything and found one of the wheel sensor is messed up and it is likely that this is what has created the issue with the ABS moduel in the first place!!! So they are replacing the bad wheel sensor as well. Mike, at this point, I am having a hard time accepting the accuracy of their initial diagnosis and don't know what to do. My question is can the messed up wheel sensor be the actual culprit to begin with and that the ABS moduel was never bad and didn't need to be replaced at all? Or can they both go bad? Or can a bad wheel sensor as they have told her damage the ABS moduel. Don't mechanic use an advanced OBD2 reader that can pinpoint weather it is ABS moduel or speed senors? I feel like if the ABS was never faulty they should not be charging me the $1300 for replacing it and only charge me for replacing the bad wheel sensor. What do you think? Also, if one wheel sensor is bad, should I replace all 4 sensors now.
@@meshkatassian8946 We are honored to help and that’s a bummer that you have had to experience this in recent days and weeks. To answer your question, yes 100%! It is 100% possible that a faulty wheel speed sensor can trigger the ABS light. To answer your question further about if the speed sensor can be the original culprit while the ABS module still good…Yes, it is possible that your original ABS module was A-ok and not faulty however we can’t personally confirm that…but…it is more common for a speed sensor to fail and trigger the ABS light…as opposed to the module failing. Hope this help. 🧰
Thanks Mike... It is so heart warming to get your input... As I have said earlier, The shop is telling me that the ABS moduel was faulty that is why it was replaced. In addition they say that the messed up wheel sensor is what has caused the ABS moduel to go bad!!! Mike, Can a bad wheel sensor as they have told me (damage) the ABS moduel? Don't mechanic use an advanced OBD2 reader that can pinpoint whether it is ABS moduel or speed senors? Or both? What can I asked the mechanics to show me to assure me that the original ABS moduel was indeed faulty and needed to be replaced? I feel now that they have replaced the $1000 ABS moduel they are trying to justify their repair work by saying that the messed up sensor has damaged the moduel!!!
@@meshkatassian8946 Thanks for the reply, we are always happy to help. Will a speed sensor ultimately cause an ABS module to fail…it’s possible…however we have never heard of that happening…🤔 We don’t know all the ins-and-outs of what the shop diagnosed and because of that…can’t give you a definite answer. But again, we have never seen a wheel speed sensor being the sole pinpointed culprit of an ABS module failure. 🧰
Hello. I have a 2014 Jeep Sahara with 7000 miles .I pressed the ESC button by accident when I was cleaning. The ABS light and ESC light came on. When I pulled away the left front wheel dragged and then released. This happens @ every start. What can I do. Thank you John .
Thanks for watching & welcome to the DIY Raptor Club John. We would start by doing a Reset. We recommend disconnecting the negative cable from your battery and leaving disconnected for a minimum of 30 minutes. After 30 minutes, resecure negative cable to your battery and see if your system has reconfigured properly. 😎👍🔧🔩
Don’t forget about BUS problems! All sensors, fuses and modules can be good but a bus / electrical issue is always possible. Can test that issue through testing for power through you’re harness or splice packs!
Ran into video and I’m in desperate need of advice. I’ve got a 2006 gmc savanna 3500 it’s not a van it’s a U-Haul truck I’ve been been through 3 transmission and every last one has gone bad. I did notice one thing when they put my 2nd one in my ABS and emergency light came on and my speedometer stop working it’s bottom out to 0mph there has been time where I’ve pass by a pot hold and it’ll trigger something and make it work again but it’ll only reach to 40mph and dye again. I’ve also notice that when the abs and the break light doesn’t appear on my dash the transmission shifts good my question to you is you think it’s the abs module? Can it trigger transmission to act up?
@@sanchezerick8377 Thanks for watching, any update? That’s a bummer you have been through two transmissions already and onto your third. Hopefully the electrical wiring for your speedometer was not damaged during one of the transmission swaps. It’s possible that it’s the ABS module however, unlikely…🤔 When was the last time you disconnected the black negative cable as well as the red positive cable and left disconnected for a minimum of 30 minutes? This will allow your system to perform a full reset.
would like to know why the u0401 and c056e codes are present and replaced the control module and the sensor under the truck reprogramed but still abs light and these codes can you help
Thanks for watching & welcome to the DIY Raptor Club. This may sound funny however we recommend verifying all 4 of your tires have the proper psi in them. We recommend filling them to the manufactures recommended max which can be found on the sidewall of your tires. By chance do you know when the last time your suspension was aligned buy a professional shop? Believe it or not, something so simple as unbalanced tires can trip your ABS system. 😎👍🔧🔩
Hi i.just ha d my honda fit replacement of rear wheel bearing and front axle assembly, we provided both parts,now when we pick up the car the eps and abs lights was on, another mechanic manuever the steering and looks like eps was off now but ABS lights still remains on
Thanks for watching & welcome to the DIY Raptor Club. Sounds like a friendly visit back to the shop that worked on your car is in the near future. They should be able to reset your computer & will hopefully not charge you any $$. Keep us posted. 😎👍🔧🔩
Good morning, just poured a cup of coffee and am sitting down to answer any and all questions for the DIY community. All was secure throughout the system however great idea to verify. 😎👍 Let us know if you have any questions and hey if you’re into crypto trading, join our DIY ecosystem and become part of an exclusive group of DIYers. toolboxtoken.com Reach out to us any time! 🧰
"OH", one more question regarding the ABS module. I understand there is a way to "reprogram" them, "OR" Flash them and clear the internal code, "HENCE" clearing your light ?? Of course, you would need to find someone that can do it, as you might also need him in case you end up using a "Used" module, since they would need to programme module to your specific VIN and model vehicle?? Thank Again !! God Bless !
Great question & it’s very possible that the video link below will help. It’s a (Quick Reset) procedure that resets system. Your procedure may be different if your vehicle is not a GM/Chevy. ruclips.net/video/Fu47rWAD30k/видео.html 😎👍🔧🔩
@@DIYwithMichaelBorders "NO" , sorry, just saw your video on the reset. And , "NO" , it's not a Chevy, we're talking 2002 Ford F-150. But so far , we have enough to at least start looking for what might be wrong, and "WHY" it is "Intermittent" ?? Thank You , God Bless !
How can you tell if it’s got moisture inside? It did rain off and on for a few days before the light came on. It literally came on after I got my tires balanced and rotated. Could they somehow have loosened this piece when removing the tire? That sounds plausible to me. Please help. Im stranded. 😢
We are happy to see you watched this video. When your tires were installed and balanced, it’s very possible that the technician slightly altered something within wheel well….possibly bumping the speed sensor and loosening the connection or even worse…damaging it…unlikely however it has happened to a few of our viewers. To answer your question in regards to checking for moisture, you can carefully disconnect speed sensor connections inside wheel well and allow them to air-dry for a few hours.
Wouldn't it be easier to check the fuses first since that is really quick? It would suck if you inspected all 4 wheels and then found out it was a blown fuse. Also, shouldn't you check the fuses electrically with an Ohm meter ?
I have a 2013 Ford E250 I replaced all 4 corners rotors and pads , works great but, now have ABS lights which come on for 10 miles then off, repeat. I had no lights before brake work 🤔I tried all your suggestions i e gas pedal 3 times etc. Had Advanced Auto check a couple times no codes 🤔 Help😰
Thanks for watching & it’s very possible that your fluid level is off. Check out the video link below, it may be helpful. ruclips.net/video/X-AJ5tD6zoA/видео.html Let’s start there. 😎👍🔧🔩
on a 2015 ford Escape, all wheel speed sensors are working fine and giving same reading, codes for ABS are C0061:54 and C0062:54 , and -2B lateral and longitudinal accelerations sensor. Is that pinpointing the ABS module itself is bad?
Good morning ☕️ any update? Let’s first perform a system reset. Below is a helpful video showing this process. ruclips.net/video/Fu47rWAD30k/видео.htmlsi=N88A6XLerFDWX8pd If that doesn’t work, we recommend disconnecting the black negative cable from your battery and leaving disconnected for a minimum of five minutes. This will also reset your ABS system and hopefully reconfigure it back to normal working operation. If both reset procedures fail, try them a second and third time as it may take a few resets to fully reconfigure your system. Still, no luck…I t’s likely the module.
I have a 1995 E320 Mercedes Cabriolet convertible that has both the ABS and the ASR lights are on. There are no error codes to reset even when you run an error code check reader. Took it to a Mercedes dealer and they had it all day while I waited for the car. They were unable to fix it and could not reset the error codes cause there aren't any. They also couldn't tell me what was wrong with car, no charge either, still not fixed. After I got the car back I took the wheel sensors out and cleaned them and the wheel spacers too, with no luck. What would you suggest?
Thanks for watching & welcome to the DIY Raptor Club. Any update? We recommend checking inside speed sensor electrical connection point. Verify it is clean & dry...no moisture, no rust or corrosion...& definitely no signs of over-applied dielectric grease...that can cause all kinds of issues. Double check your fuse box to ensure any and all fuses related to your ABS system are properly secured and have no moisture or corrosion on the leads. Let’s start there, keep us posted. Let’s get this figured out. Us fellow DIY’ers need to stick together!
@@DIYwithMichaelBorders Thank you for your reply. All of the fuses were replaced with the copper ones the original ones as you know were aluminum. There is no separate fuse listed on the fuse box diagram either. I thought of replacing just the wheel sensor wiring but they are no longer available from Mercedes, and no after market either. Now what?
Hi I have a holden captiva which I replaced the abs module due to dealer scanned it and said will need to replace so I used 2nd hand one just wondering as the abs lights are still on will it need to be reset or programed ?
Good morning ☕️ Awesome job making it a DIY project. A reset procedure is recommended, and it may be as simple as just disconnecting the black negative cable from your battery and leaving it disconnected for a minimum of five minutes. 👍🧰
Can you tell if the magnetic ring should have magnets all around the ring? Because I replace the ABS sensor and watch that ring but it only had a few magnets... very good video by the way!
Thanks for watching & welcome to the DIY Raptor Club. This will depend on the vehicle however almost all designs are of the ring magnet method. By chance have you had your vehicle hooked up to an OBD scanner to read your ABS codes? This will allow us to pinpoint the exact part that’s causing your ABS light to come on. In most cases, your local AutoZone will read your codes for 100% free. Please keep us posted. Us fellow DIY’ers need to stick together! 😎👍🔧🔩
Hi, Is I disconnect the connector on my original abs module, and then I reconnect the connector for only cleaning contacts on the abs module must I reprogramming with vcds or not ?
@@massimopica5008 Thanks for watching, some model vehicles will require it however not all. Try disconnecting the black negative cable from your battery and leaving disconnected for a minimum of five minutes. This will allow your system to perform a reset and likely reconfigure your ABS system and sensors to the main onboard computer of the engine.
I do have an 1994 Olds Cutlass Supreme S 3.1 & my ABS light does come on & done the RESET which I seen ,but all it does is to lock the doors,however when I put the car in drive that's when it'll come on again
Good morning, just poured a ☕️ and am sitting down to answer any and all questions for the DIY community. We are honored you took the time to share your experience. Since your vehicle is doing that, it’s likely that there is a part within the ABS system that is faulty. May need to have your ABS system checked for fault codes. Let us know if you have any questions and hey if you’re interested, join our DIY ecosystem and help us grow an exclusive group of DIYers. toolboxtoken.com Reach out to us any time! 🧰
Thank you for this video. I have a unique problem that has stumped 3 mechanics and at least 2 really good computer coders.. My truck (2008 Chevy Express 1500 Cargo Van) had a problem that was traced to the throttle body harness. It was crimped. Replaced and 4 new tire sensors as well. Problem I experienced was check engine light and van putt'd & sputtered. Towed to mechanic and above fixes. Since then (3 months) intermittent ABS/Emergency brake light comes on and stays on for either a couple hours or all day. I have since noticed the check engine light periodically coming on at the same time. It eventually goes out, as do the other 2 lights. Today, I had to be towed. The van was showing signs of putt'n & sputtering while sitting idle. All the lights mentioned were on. My last stop I noticed the van felt as if it wanted to surge slightly while in gear and brakes applied. The speedometer was fluctuating up and down as well. Once under power the check engine light started flashing and I lost power. After shutting engine off and starting again...check engine light solid. Once under power for less than 1 minute...check engine light began flashing and loss of power. Mechanic is stumped. Any chance you've encountered this situation? Kim D.
Hi. i have an abs esp fault. i have had it plugged into a computer and the fault says front right speed sensor. I replaced this, check the wiring for freys. also i replaced the full hub. fuses too. unfortunately the fault still comes on? it's intermittent
Thanks for the great video. I have the same problem with Cadillac Escalade ESV 2016.in raining, few lights get ON, traction, ABS,and the steering gets harder even undeliverable. Do you think these are the same issue and can be fixed by changing sensors?
Good morning & welcome to the DIY Raptor Club. We recommend starting with the fuses. Check to ensure all fuses related to ABS system are clean, not rusted or corroded, as well as the fuse box internal leads that fuses connect into are clean, dry, & not melted or damaged. If all looks good, it’s time to direct attention to the sensor. Let’s start there. Please keep us posted, us fellow DIY’ers need to stick together! 😎👍🔧🔩
Thanks for watching & good morning, we are drinking our morning coffee answering any and all questions for the DIY community. That’s very kind of you to share Frank. We are always here to help answer questions, enjoy your weekend. 😎👍
ABS light on my 1987 Vette is now on after the mechanic installed new front brakes due to it jerking to the left when braking. This did not correct the problem. He said the ABS system was bad. I found a used one on eBay. This still didn’t solve the problem. The light is still on.and the ABS is not working. Any input from you is appreciated.
Thanks for watching, any update on your findings…? It’s likely that you have a damaged caliper and piston. It’s also likely that you have an electrical issue within your ABS module. Looking forward to hearing back from you.
All 4 brakes and rotors were replaced on the car. Neither the ABS or Traction Control lights were on before they were replaced by the shop. I tried to do the quick reset, but that didn't work. Any ideas, I checked the first 3 common causes from this video and then all looked good. Thanks
Thanks for watching & we appreciate you sharing this. That’s no fun. We have attached a quick DIY reset procedure that may help... it’s possible that it’s the same reset procedure that the shop did. ruclips.net/video/Fu47rWAD30k/видео.html If this does not work, you may want to disconnect the black negative terminal to your battery and leave disconnected for a minimum of 30 minutes. This will allow your system to complete a full reset. After 30 minutes, re-secure cable to battery and see if your error codes are no longer illuminated. 😎👍🔧🔩
I turned off my car after getting 4 lights on it and when i turned it back on all the lights were gone (including abs). Could rain cause something like this to happen?
Thanks for watching, rain can definitely lead to trapped moisture inside a wheel speed sensor. That’s up there with the top common cause issue that triggers ABS light to illuminate.
2008 jeep liberty my asb light comes on randomly and takes over my car. I can pull over and hold down the dash millage button and it resets. But the not knowing costs money, anyone can take advantage. Can you see the problem with the computer?
Thanks for watching Dennis & welcome to the DIY Raptor Club. Let’s get this figured out. Let’s first start with a system reset. Below is a link that will guide you through a System Reset. If it works...great...if not, onto the next option. ruclips.net/video/Fu47rWAD30k/видео.html Again, if reset does not work...&...since your ABS light comes on, we recommend visiting your local AutoZone where they can hook up an OBD scanner to your vehicle and read your onboard computer ABS codes. The error codes will help pinpoint the exact part causing the issue. Please keep us posted Dennis. Us fellow DIY’ers need to stick together! 😎👍🔧🔩
I have a 03 Ford Expedition. I'm currently trying to diagnose a brake issue. My vehicles calipers on both the driver and passengers side are severely sticking. Would that be an issue with the abs pump or the master or both?
Good morning, we appreciate you sharing this. Us fellow DIY’ers need to stick together! It’s unlikely that it’s a faulty Master Brake Cylinder (MBC) however we can’t rule it out. Have you performed any recent maintenance on your brake system in the last few months? This will help us pinpoint whether or not any recent maintenance is tied to your issues. Keep us posted, welcome to the DIY Raptor Club, hope all is well. 😎👍🔧🔩
@@DIYwithMichaelBorders it was the abs pump. I acquired the vehicle from a friend and they did some maintenance on it trying to figure out an issue several years ago. It turns out the abs fuses were missing.
@@TherealWinterpillow Very cool & we appreciate you sharing this update. Back up & running is a great thing. Hopefully many stress free days ahead for you. 😎👍🔧🔩
My abs light went on other day, I pulled into a parking spot but my from wheel grinded, then didn’t after I stepped the brake. Pads are good, rotors are good, bearing I never had a problem with it, no noise or vibration and always drove straight. I’m hoping it’s just the abs sensor and the grinding abs attempting to hold up
Thanks for watching & welcome to the DIY Raptor Club. By chance is your ABS light illuminated at the moment? If yes, we recommend hooking an OBD scanner up to your engine to read the ABS fault code. This will help pinpoint the exact part causing your issues. AutoZone hooks OBD scanner to your vehicle and reads your fault codes for free. Please keep us posted. 😎👍🔧🔩
Hello, thanks for this video🙏. My car is SATURN 2007 and today I see ABS light ON , time to time my I see TRACK OFF on the DASH, please tell me what I can do!
Thanks for watching, any update? Below is a reset procedure that may help reconfigure your ABS system. ruclips.net/video/Fu47rWAD30k/видео.htmlsi=v8okjdlphwVSe91G 🧰
Thanks for watching, unfortunately that will begin to trigger many additional fault codes that will lead you to think additional parts have failed when they are still working…leading to components degrading and lessening the overall performance/reliability of vehicle. Are you having trouble finding replacement fuses?
Great video. Based on comments here and elsewhere, it seems almost inevitable a mechanic or dealership tells you it is the module, big ticket item which is the problem. You want to get a kick? Next time you talk to the guy at the service desk, work into the conversation how you have researched your problem on YT and then look at their reaction. It's facial because they don't respond verbally.
Haven’t read all the comments but my 2010 Prius has an error code 1391 Abnormal leak off acc press. Toyota had a voluntary recall I missed due to getting the car second hand. The repair is abt $3000 to replace the brake master cylinder and pump. Is the code definitive or should I consider the causes you mentioned in your video. All this happened after getting my brakes and or tires replaced
Thanks for watching, any update? Before doing anything, we recommend carefully disconnecting the black negative cable from your battery and leaving disconnected for a minimum of 30 minutes. This will allow your entire system to fully reset. After 30 minutes, resecure black negative cable to battery and start engine to verify that the onboard computer and all electronic sensors that communicate with it have fully reset and reconfigured themselves properly. This will hopefully save you $3000.00 😁👍🧰
@@DIYwithMichaelBorders Even if the brake feels squishy? I’ve reset the lights but they come back. I haven’t tried disconnecting the black cable as the car is now across the country. I can ask my brother to try your recommendation. Thanks!
Thanks for watching. Below is a helpful reset procedure video. Keep us posted. ruclips.net/video/Fu47rWAD30k/видео.htmlsi=K2QgeuNXf-aafcl1 Let us know if you have any questions and hey if you’re into crypto trading, join our DIY ecosystem and become part of an exclusive group of DIYers. toolboxtoken.com Reach out to us any time! 🧰
Wow just have to say. Props for trying to help as many people as possible in the comments. Like wow you’re amazing dude. If you’re still answering questions, I have one. So my car has had the traction light on for a bit, but sometimes when I’m driving, abs and break lights turn on. Also, my car just started moving the speed diameter up and down in the middle of driving. The car feels perfectly fine, but, kinda scare about this symptoms. Already took it too a shop, but they couldn’t fix the problem and I have nooo idea what it might be. I am willing to pay for a abs module but idk if that’ll be the problem
Thanks for watching & welcome to the DIY Raptor Club. Let’s get this figured out. A few things to do. 1. Verify all 4 tire pressure reading are set to manufacturers recommended psi. Believe it or not, low tire pressure can trigger abs in newer modern vehicles. 2. If you live in snowy areas, snow, ice, water, & moisture can sneak into abs sensor electrical connection points. This leads to abs turning on. In this case, disconnecting electrical connection and cleaning/drying will hopefully help. Let’s start there. 😎👍🔧🔩
@@DIYwithMichaelBorders thank you and yes. all tires are set to manufacturers specs. Also, idk when people say new because i have mostly owned old cars lol. The car having this problem is my 2012 Dodge Avenger and i live in Arizona where the lowest we get is 40F and a high of 118. So maybe the second step would be ruled out? or would you still recommend me checking it out? Also have switched most of the fuses in the fuze box. Now, i didnt touch those big square fuzes found in the box (sorry dont know the mechanic lingo lol)
@@MooseX2012 Thanks for the reply & is your ABS light illuminated on instrument cluster? If yes, you may want to visit your local AutoZone & have then read your ABS error codes. They do this for free. Obtaining the error codes will hopefully help pinpoint the part causing your issues.
so a month ago I did the annual servicing oil my chevy cruze and when I went to pick my car the ABS light was on and the pump kept running even after turning off the car the car mechanic managed to turn the pump off but the ABS light is still on, I went to another mechanic he said the abs module need to be changed and today I showed my car to another mechanic he said the booster cylinder need to be changed but at this point I don't know if I should trust any of these mechanics any advice which route I should take? FYI my car is 2013 chevy cruze 2.0 has ran only 52000km
Good morning & welcome to the DIY Raptor Club. Let’s get this figured out. 1st... we recommend visiting your local AutoZone where they can connect an OBD scanner to your vehicle and read the onboard fault codes. If your ABS light is illuminated on your instrument cluster, the OBD scanner will be able to detect the fault code which in return will pinpoint the exact part causing the issue. Let’s start there, keep us posted. 😎👍
do you teach at a 10th grade or lower level? just wondering cuz you have a very calming voice and tone that might've helped me learn math early on and you take your time with the explanation and not stress me out like some other teachers used to do when i was in grade school
tranquil Nice Thanks for watching & we really appreciate you reaching out to us. We do our best to be as precise and helpful as possible. 😀 Let us know if you have any questions. Us fellow DIY’ers need to stick together!
My mechanic said I needed an abs pump....so I got a used one and now my abs light is on....considering to put back my original abs pump to see if abs goes off......your take on it?....
Thanks for watching & sharing this. Before removing new part, we recommend performing a system reset. This can be accomplished by removing the black negative cable from your battery and leaving disconnected for a minimum of 5 minutes. After 5 minutes, resecure cable to battery and start engine. Please keep us posted. 😎👍🔧🔩
@@DIYwithMichaelBorders another mechanic did a scan and said abs pump.....like I said the first mechanic said I needed an abs pump and he put in a used one and now abs is on....considering to put back my original abs pump to turn off abs light.....light was never on before....
I just had to replace both wheel hubs and the rotors, pads, and calipers on my 08 Colorado and the ABS and Fault light are still on. How do I get them to go out or do they go out on their own after driving it?
Thanks for watching & welcome to the DIY Raptor Club. Below is a link to a video that shows removing pads & rotors. ruclips.net/video/S0temq1xiQg/видео.html We are removing the pads and rotors during a hub assembly replacement. 😎👍🔧🔩
I replacing my ABS control module due to a nasty leak. It's on a 2006 lexus IS350. Once replaced does it require a reprogramming process or is it just simple plug and play?
Hello, I have a 2005 Chevy Colorado, and I have a ABS fault, traction control fault, stability control fault, all going off and has shut down my traction control and ABS. I have checked the rings, replaced the sensors, cleaned all connectors, and checked fuses. I got the truck from my brother who has had problems with the abs and traction control ever since he bought the truck. He actually had wheels lock up on him driving down the highway, after replacing the sensors it was running fine, then when we were driving we noticed one wheel started dragging and the front right wheel started grabbing spirraticaly. We cleaned the rings and sensors and it stopped but then suddenly threw 3 faults and we can't figure out why, please help have no idea where to turn.
What can cause traction fault, abs and brake lights come on and then the heater fan speed stops, no blinkers hazard ,windows don't work ...any help will be appreciated..thanks
Thanks for watching & welcome to the DIY Raptor Club. The most common cause is a faulty speed/hub sensor. If you live in an area where there is snow, slush, ice…wheel-well can accumulate lots of snow, slush, ice buildup & cause havoc on sensor... leading to all sorts of bells and whistle‘s going off on your instrument cluster. Keep us posted on your project.
Hello, thanks for the good video. Is it possible for the ABS module to work with only one speed sensor? Actually, I am a student and I want to present the operation of ABS with a single tire and a brake unit using a single speed sensor.
Thanks for watching and without the speed sensor, the ABS module will still communicate with the other wheel sensors and operate as designed. Most vehicles will still have a built in safety feature that allows ABS to engage on all wheels however the one with faulty sensor will behave sporadically.
@@DIYwithMichaelBorders Actually, I have created a project with single wheel and break assembly, and demonstrated the ABS module on a board, normal break is okay but anti skid not working, so i am stuck now. I want to ask is it necessary for ABS module to get all four sensor inputs to operate? Or we can use single sensor, or can we divide the output of speed sensor to four inputs for ECU??
@@livetech4062 We appreciate the follow up. Below is a link that dives deeper into how the speed sensor operates in conjunction with the hub. Pretty unique design. ruclips.net/video/8CRXheZ_72Y/видео.html 😎👍
I need to completely clean out my brake lines from contaminated fluid. I want to blow break cleaner through the lines but will it mess up my abs? What to do? On a 2004 civic, discovered daughter put power steering fluid in the master cylinder.
Thanks for watching & we appreciate you reaching out to us. You can purchase a flush kit at your local AutoZone which will come with directions on how to properly flush system as well as doing it in a way that protects your ABS system. You may want to contact them & ask if they have one in stock prior to driving there. Keep us posted. 😎👍🔧🔩
I love the way you teach: clear, concise and articulate. Thank you.
@@stevenwiedel3122
Very nice of you to say, thank you.
😁🧰
Outstanding! The best, clearest, calmest, most informative car video I have ever seen. Thanks!
Thanks for watching & we really appreciate you sharing your kind words. Great to hear the video helped.
Let us know if you have any questions Terence, us fellow DIY’ers need to stick together!
Hope all is well with you and your family.
Even I want to be a mechanic after watching this professional video...
Well done!!
@@Connie1Fan
You have officially joined the DIY community. 😁👍🧰
One of most clear explanation and best camera work I’ve seen in a DIY video. Thanks
Spicly123
Thank you and that’s very nice of you. We really appreciate your comment and we are always here to help answer questions.
Please subscribe to the channel and ring your RUclips bell 🔔 this will be very helpful to us thanks again.
😎👍🔧🔩
Absolutely.
Mr Testicals
😎👍🔧🔩
@@DIYwithMichaelBorders flashed. The flash light its still on, but can I ask you what you believe the problem might be? I tried again to flash the big lights it happened again, ABS flashed and car reduced speed.. I would appreciate if you can give me your advice
CancelIKL
Thanks for watching, this usually happens when there is an electrical short. We recommend inspecting all wiring for any loose connections. A slightly loose wire can lead to your exact issue.
😎👍🔧🔩
Magnificent video and magnificent edition; Thank you for bringing to light an issue that for me was unknown, till today that the Light of the ABS was set on my car's dashboard.
Blessings 🙏
Good morning. ☕️
Great to hear our video was helpful, and you are very welcome. Thank you for being kind enough to share this comment. Hope you have a great weekend.
😎👍
Excellent, thorough and slow description. Thank you.
Good morning Ray, thank you for this. We do our best to give the DIY community all the help we can, many more helpful videos to come!
Welcome to the DIY Raptor Club.
Thank you so much. This is my current situation with my Chevy Equinox 2016 that happened today. I panicked and rushed to a local repair shop for a diagnostic and got a quote for $800 to replace the ABS module 🥲🥲. My heart dropped from that shocker.
So I resorted to Googling the issue and your RUclips video popped up for the reset trick so I will definitely try that in the morning. If not, I will refer back to this specific video for additional help.
Thank you tons. I will post an updated comment if all is successful either way.🙏🏾
You are very welcome, $800 is a chunk of money that you can hopefully keep in your pocket and spend on something more meaningful.
Keep us posted and hey if you’re into crypto trading, check out our newly launched DIY ecosystem.
Toolboxtoken.com
Reach out to us any time! 🧰
were you able to pick your heart up after the shock? I know the feeling!!!
So?
Overall good video, only one point that I have issue with. The two block fuses are not dealer only and can be purchased at most parts stores and even most Wal-Marts in the automotive section.
Thanks for watching & sharing. 😎👍
Excellent video! Very thorough and informative. Your voice is very calm and easy to understand. Good job 👍
Thanks for watching & sharing this.
Agree about the clear voice and delivery, that really does make a difference.
ESPECIALLY APPRECIATE YOUR TEACHING SAFETY TIPS !! YOUR ONE OF THE FEW WHO TAKES SAFETY FIRST !! THANK YOU FOR THE TUTORIAL !! EASY CLEAR VIEW VIDEO AND LISTENING !!
Thanks for watching & welcome to the DIY Raptor Club. Safety is very important & we appreciate you reaching out to us. Let us know if you have any questions. Enjoy your day.
Great presentation.
The control circuits on these ABS systems are typically low voltage, low amperage, which means you need to check the ABS Module grounds after you check the fuses, or check the separate voltage values either at the wheels yourself, or the voltages coming into the ABS module while a second person helps you by spinning each separate wheel one-at-a-time, but at a uniform rate. As I understand these systems, the interaction between magnetic part of the sensor assembly and the notches in the rotating wheel on the hub assembly generates the voltage measured as the wheel turns. Trucks are usually exposed to harsher conditions than cars, and exposure of the wheel sensors and connectors to water, sea water at the beach, salted roads, etc. over the years can result in degraded sensors at the wheels, or poor or corroded grounds or bad connections where the system wires connect to the push-on or screw-on connectors. Any of these issues can cause voltage variations that prevent the ABS system from knowing whether or not all 4 wheels are rotating at substantially the same speed, and if the signals aren't the same, the ABS light comes on.
The profit margin between replacing the ABS Module and the sensors and sensor wiring on 4 wheels and bleeding or replacing the brake fluid is about $1,000 to 1,500 more than doing the checks he recommended, plus checking the grounds. The ABS module can be replaced with a new one, if necessary, without replacing the valves it is attached to, but it is likely it will have to be re-programmed for your specific vehicle. Programming Specs are often available online, but require special equipment. The alternative is sending a defective ABS module to a specialty shop which can repair the old one, and do any required programming. Costs vary, but usually much cheaper than having a new one programmed and installed - unless you have a shop that does this locally, it can take about ten days to send it and get it back, due to shipping times.
P.S. The white illuminated board you have behind you in your videos is interesting, but it leaves your face in the shadows. Viewers like to see faces; something for you to consider.
We appreciate you sharing your thoughts and info. Always welcome here and much appreciated.
We have improved our intros since this series. If you have time, hopefully you will visit our channel.
Hope you’re having a great weekend.
😎👍
Great explanation. We are having the issue of both the ABS & the BRAKE LIGHT COME on.
@@evelyncantrell2754
We appreciate that. We are here to help answer questions.
Thanks for the excellent video. And I appreciate it when you guys tell us girls who can help out with free services like OBD scanner checks. Very cool.
Thanks for watching & welcome to the DIY Raptor Club. We appreciate you reaching out to us. Let us know if you have any questions. Enjoy your day.
Both my daughters do all their own maintenance and repairs on their vehicles. They grew up helping me in my shop and learned not only how to do a lot of jobs but how to do so safely.
Thank you this was informational I'll tryout everything tomorrow and see if once brakes are done it goes away too
@@chiefledis.holidayakaladil7376
We really appreciate that, thank you.
2009 Dodge caliber 2.0 ABS light came on. Lifted front end up and ran it to 50 mph and listened for bad bearing. Sounded fine both sides. Checked each back tire and turned by hand and all seemed fine for noise. Grabbed each tire and wiggled and evrything seems tight. Asked my son about the tire pressure and found that all the tires were at 25 to 27 psi. Filled all tires to 33 psi and we took it for a run. Guess what the abs light went out. Completely surprised me.
Check your air pressure of the tires first. It was a very simple fix............................................
Thanks for watching & we really appreciate you sharing this. That can definitely do it. This is great advice.
Welcome to the DIY Raptor Club. Us fellow DIY’ers need to stick together.
😎👍🔧🔩
So useful n professionally the way you explain
Really you deserve to be rewarded by utube
Ahmad Kamali
You’re too kind & we appreciate that. We DIY’ers need to stick together & help each other. 😀
We have several more videos regarding that annoying ABS light on vehicle dashboard’s...the ABS light has unfortunately become an annoying nightmare for many drivers.
😎👍🔧🔩
Thanks for the info education on abs symptoms and possible causes creating abs light on dash. I'm trying to determine if the mechanic that told me my abs pump is failing is correct or not where as they said my coolant leak was coming from heater coil gear assembly but wasn't case and I paid $500 for that to be replaced and installed then that evening my abs light came on. I've bn spending money on repairing front suspension system.
Have yet to replace engine mounts, brakes, and rear suspension as well as tires brakes and then eventually replace interior seating, steering wheel and center console gear shifter and compartment ..
Good morning, you are very welcome. ABS pump failure is not uncommon however if vehicle is less than 10 years old…it’s unlikely that the pump has failed.
It may be as simple as a speed sensor however without hooking up OBD2 scanner, we can’t confidently say.
Having a scanner will help pinpoint the exact part causing your issue.
I have a 2011 Dodge Ram 1500, 3.7 Engine V6 w/only 74,000 miles bought it brand new. About 16 months ago, the ABS light came on the Dashboard, thought it was the rear sensors, I changed out both, but the ABS Light did not go out. So I took it to back to the Dealer where I had bought the truck way back then. So the issue was the ABS Modulator, had it replace cost about $1,800.00 Drove really good for about 18 months, and last month the ABS Light came back on again, now I am not a mechanic, and am not mechanically incline. Just a few basics, I went to several shops, they all told me the same thing, ABS Modulator w/code C-1073, again it was the ABS Modulator. Finally took back my truck to the Dealers, they said, ABS Modulators are no long made, but they are Re-manufactured, in other words rebuilt w/a 6 month Guarantee . So I paid about $800, and the Re-built ABS Modulator was installed and Re-program. All is well, but what I want to say is, I am keeping this truck till one of us goes up into the sky, either me or the truck. So this time that I had another ABS Modulator installed, I told the Dealership I wanted the ABS Modulator that was on the truck to be given back to me. And I got it back, and am sending it off to have it repaired. I will tell you why, because it is ALL READY PROGRAM for My Truck. The Cost to Re-built the ABS Modulator is only about $300 total, but those that are sold, are not Programed for the car or truck it is going in too. That's why Companies ask you for a Vin Number when inquiring for a ABS Modulator. Getting back the ABS Modulator may save me money down the line, but it is the Programing for my own truck that is most important to me.. So am back on the road, and Merry Christmas to all.
@@PaulGuerrero-d8o
Good morning ☕️
Thanks for taking the time to share your experience. That’s a great idea asking for your Modulator back. Getting it rebuilt and also having it already programmed for your exact truck is “money in the bank”.
Sounds like you take great care of your 2011 Ram, and that goes a long way in keeping the vehicle reliable and on the road.
Reach out to us any time. Many more helpful videos to come. 🧰
Loved the video. Just trying to find ways to check my abs on our Chevy Colorado 2012 ABS system before taking it to a mechanic. Thanks much --great advice on what to check on. Will try what I can.
Thanks for watching & sharing this, that’s very kind of you to take the time to reach out to us.
Let us know if you have any questions, us DIYers need to stick together!
😎👍
First time watching. Can't believe I can actually SEE the stuff you are talking about. Awesome camera work and explanations. Thank you and subscribed.
Mike Angel
Thanks Mike, we really appreciate that. We just subscribed back. Let us know if you have any questions.
😎👍🔧🔩
Didn't read all comments but FYI the larger fuses are also available at most auto parts stores and even Walmart.
Absolutely PERFECT video and way to fix (or in my case) have knowledge of what is causing this issue on my old Dodge Truck.
Elaine R
We appreciate that & thanks for sharing. Let us know if you have any questions.
😎👍🔧🔩
Agreed!!!
Thank you, thank you and thank you for making the comments on having a secondary support for a jacked up vehicle. I see so many vids of people working under a vehicle with only one hydraulic support. Especially do not trust a hydraulic jack. My engineer dad and military training drilled this into me for years. It is a golden rule of working on heavy items. A set of jack stands is a cheap safegaurd and way cheaper than a hospital visit or a funeral.The video content on the troubleshooting was great.
David Crews
Thanks for watching & sharing your thoughts David. We couldn’t agree with you more. Safety Safety Safety! 😀
We appreciate you reaching out to us. Us fellow DIY’ers need to stick together!
😎👍🔧🔩
for over 50 years cars operated without abs . we don't need it Ralph Nader.
Absolutely, just another useless invention to screw money out of us. Abs light can come on but there's nothing wrong with wheel rotation, it's all down to a damaged or failed senser or it's associated parts.
Yep. I’m 18 my car’s ABS has been out for three months now, best believe I’m not buying a new abs motor/pump for $200 if you can drive with it you can drive without it
It put my car in limp mode so I need it lol
I recently bought a car and bypassed the ABS system and now the brakes are working better than when I got it 😊
Just installed the wrong bearing on a 2003 element awd and it has abs now I have the abs light on but even before that I had it on, and before that I was borrowing my brother's 1976 vw bug...we definitely don't need abs we need people being are of how to drive the car properly. I've seen people with abs hydroplane or crash even with the abs engaged. Abs doesn't fix idiots
Great video. Very clear and concise. I have a 2009 F 250 and my ABS light comes on intermittently. There doesn’t seem to be any pattern to it. The brakes are working fine without the ABS. I bought a Blue driver scanner and I’m getting code C1096 Pump Motor Open Circuit. I’m going to dive in on this next week, but was wondering if because it is intermittent, do you have any insights?
Thanks for watching & welcome to the DIY Raptor Club. Let’s try something. We recommend filling all four of your tires back up to its proper psi. See if this registers & runs off ABS light. Keep us posted.
Enjoy your night! 😎👍🔧🔩
Question. My 1992 LT1 Corvette , has a problem. For the life of me I cannot spin or smoke my tires. The emergency brake warning light is always on. So I checked The brake fluid which is full,I changed all four of the brake pads on the entire car and the light is still on I also checked the wheel sensors some of them had rust buildup on them but I cleaned them going back in so why the hell cant I spend the tires on a Corvette. What is the use of owning a Corvette if you can’t smoke the tires that’s my problem I’ve been building dragon jeans for my older cars but I can’t figure out the brake light is unbelievable but he’s got an idea what it is let me know because I don’t see nothing on RUclips about it I even called the dealership and they won’t tell me they want me to bring the car in to take my money that shit ain’t going to happen. When I bought this Corvette I didn’t even realize until I lifted the hood after I got home there’s a Optispark distributor what kind of crap is that what’s a matter with the old Style ones on top of the back of the engine.
Thanks for watching & welcome to the DIY Raptor Club. An OBD scanner can help pinpoint the exact part that is causing issues to your brake system.
AutoZone will read your fault codes for 100% free.
Know nothing about cars, motorcycles me, using your vid managed to fix the abs light .excellent vid easy to follow even by me .
Thanks for watching & welcome to the DIY Raptor Club. That’s great to hear and we appreciate you sharing this, enjoy your night.
😎👍🔧🔩
2006 Toyota Highlander 3.3L gas. I'm having an ABS issue, which I was told by my mechanic, that the first step is to replace the abs module. I'm getting the following codes C1223, U0073, U0123, U0124, U0126, C0371, and C1281 I can't find anyone that will rebuild my abs module. I understand they are extremely expensive at the dealer and I believe they are discontinued. I thought about buying a used one, but I don't know where to get it reprogrammed. I heard the dealers don't reprogram them unless it's a new one. Does anyone know where I can get it rebuilt? Oh by the way, the issue that started all of this was the day after bought it. It drove fine at the dealership and the next day, i was on a busy road and all of a sudden it lost power while accelerating and I would have to push the accelerator down all the way just for it to move 10 mph. The abs lights came on and the traction control as well. I'd appreciate any advice. The shady dealership told me I had a 1 week/1000 mile warranty that if ANY THING went wrong that they'll fix it. I called them and they said to look at my paperwork that I bought it as is and they refused to help me in any way. I did take them to court and won. I received a full refund and I was able to keep the car for free, minus the $750 I had to pay an attorney.
Awesome information/tutorial, the only observation I want to make is that not all abs systems are the same there are different cars that have different abs systems.
Good morning, just poured a cup of coffee and am sitting down to answer any and all questions for the DIY community.
We really appreciate you watching and sharing your thoughts. Any and all helpful info is greatly appreciated!
Let us know if you have any questions and hey if you’re into crypto trading, join our DIY ecosystem.
toolboxtoken.com
Reach out to us any time! 🧰
Brilliant bit of information. I had a passenger front sensor come up so it was replaced and one 15 minutes later after leaving the garage the ABS came on again and now it says the driver side rear sensor needs replacing. Could that be possible ? Or could it be the fuse or abs module ? Thanks
PERFECT video! My Mitsubishi outlander 2010 is recently showing ABS light issue. It is coming on and off on the dashboard. When it is on, then ACS off light turns on. The car is running well so far, no brake issue whatsoever with ABS light on. I have driven 5K+ miles with ABS light on. I got P1773 and C2116 codes. How serious is that?
Hello & thanks for such great videos. I have a situation where my 2005 Colorado goes into "Reduced Power" and then shows the message "Traction Fault". Would you happen to know anything about this? I have gone to soo many places & dealers & they can't figure it out because they can't replicate the situation because it only happens randomly. So when it happens, I get stranded for a few minutes, I shut it off, wait a few minutes and then I'm able to get going again. Now the weirdest is that EVEY TIME this happens, my power locks stop working, so I have to disconnect the battery for a few minutes and everything works back to normal again.... any advise? It would be GREATLY APPRECIATED!!!!
Good morning, just poured a cup of coffee and am sitting down to answer any and all questions for the DIY community.
It could be an electrical issue. You may have a loose connection…we recommend inspecting any and all electrical connections and fuses related to ABS system as well as the Traction Control system.
You might even have a part in its early stages of failure…which because of this…the part itself is working intermittently. Please keep us posted.
Make sure all tires are properly inflated to the manufacturer max recommended psi.
Let us know if you have any questions and hey if you’re into crypto trading, join our DIY ecosystem.
toolboxtoken.com
Reach out to us any time! 🧰
@@DIYwithMichaelBorders Thank you very much for taking the time to respond. I will try your recommendations and keep you posted! I greatly appreciated!
@@ErnestoGonzalez82
We are happy to help. 👍
Great Video man ! Any idea the ABS/ESP doesnt light up on dashboard after you turn on key ? i checkt fuses but dont know exactly the problem
@@dracony7649
Good morning ☕️ any update?
It’s possible that the lighting for that indicator has burnt out however that is very uncommon and not likely the case.
We recommend disconnecting the black negative cable from your battery and leaving disconnected for a minimum of five minutes.
This will allow your system to perform a full electrical system reset. After five minutes, resecure black negative cable to battery and check electrical system by turning the key on, followed by starting the engine.
This reset will hopefully remove any electrical glitches or malfunctions within the system and get your computer back to proper in normal configuration.
@@DIYwithMichaelBorders thank you so much will try to do this method if it works 👍👍
@@dracony7649
😁👍🧰
Hi, I would like to suggest another possible cause of ABS light on, brake light switch. At least it was true for my 95 GMC truck, after going through every possible cause without any result, by changing brake light switch it went away. In fact the faulty of my break light switch showed no problem with my actual brake lights, they worked fine, but it had caused ABS malfunctioning as well as problems with my ignition switch, control module and some other electrical problem as well. By changing that part, all my troubles got resolved, I thought it's worth mentioning my experience here.
Good morning ☕️
We are honored you took the time to share your experience and what solved issue for your GMC. Awesome job continuing your DIY project to diagnose the cause.
Thanks again, much appreciated. 👍
I can't do a quick reset due to no key only a fob 2018 Jeep Cherokee codeU140A right front wheel speed sensor. It was your prior video of pumping the gas pedal then start?
Great video, I have a Ford explorer sport Trac 2008 and I recently replaced my tires of the vehicle and it recently started to turn on my abs light once I speed up to 15 mph, breaks work perfectly fine with no issue so I'm stumped as to why, I'm unsure if wheel unalignment may also have something to do with it.
Thanks for watching & welcome to the DIY Raptor Club. You mentioned you just recently replaced tires.
Believe it or not, it may be as simple as bringing your air pressure inside your tire up to the recommended max psi.
Please keep us posted.
Wow!? My tire is quite low on air
Thanks for your knowledge of ABS. I recently replaced the two rear shocks of my 2012 escalade esv now the ABS, traction control, stabilitrak lights are on. The vehicle runs normal obd scanner shows no codes. Any clue? Thanks for responding.
Thanks for watching, it may be as simple as a quick reset.
We recommend disconnecting the black negative cable from your battery and leaving disconnected for a minimum of five minutes…which will reset your computer.
After five minutes, resecure black negative cable to battery and start engine.
@@DIYwithMichaelBorders hey thanks for the quick response. Still 3 lights showing after did what you suggested. I checked all tire pressures, wheel sensors wiring look fine. Basically the vehicle runs normal no limb mode. I'll just keep driving it maybe lights will turn off eventually.
@@chester3753
Thanks for the update? Did the battery connections feel loose…?…in other words, after you tighten 10mm nut to secure battery cable to terminal…can you move it easily or is it locked in-place?
A loose connection can trigger miscellaneous errors such as ABS.
@@DIYwithMichaelBorders cable is secured not loose at all.
@@chester3753
Awesome. 👍
Is it possible for this light also to just be triggered by dirt, dust collecting in that whole area around the wheel with any of those parts?
@@candlelightbeesgardening
Absolutely! In addition, this time of year can cause havoc on a vehicles ABS system while driving in snow, ice, salt, slush, and dirt.
However back to your question, dirt making it’s way onto, into, and around ABS components can definitely trigger the vehicle’s ABS light to illuminate.
😎☕️🧰
@@DIYwithMichaelBorders Thank you for the reply!
@
We are happy to reply. They DIY community is the BEST!
Hi, I own a Ford Escape 2009 2.5 engine FWD and appears the ABS and TCS light on. I scanned and shows the B2900 code, In my understanding it means that the ABS VIN module doesn't match with the mean computer. According to the shop it needs to reprogram but is too expensive. I have a basic scan and I can delete that code but when start again the vehicle appears again. So, the specific question, do exist any alternative method to correct o delete this?
As a comment, I checked the 4 wheel sensors and looks good.
Thank you from Chihuahua Mexico.
Thanks for watching Luis, you can start by a simple reset by disconnecting the battery for 30 minutes.
It doesn’t work, module reprogram might be best.
@@DIYwithMichaelBorders Thank you, I will try doing that
@@luis.gallegos87
😎👍
This is very good tutorial on abs light on.
My question is am rx 300,1999 model having same abs light on and speedometer not working what can I do pls but the transmission gear still working.
Thank you this very informative video ii do hope i can get some help with my question which is; my abs light stays off when i start the car with my foot on the break pedal but as soon as i release the pedal my abs light comes on. Help me please. Toyota 4runner 2000 limited 3.4L
Thanks for watching, this usually happens when the system detects low brake fluid. We recommend adding the proper brake fluid and bringing it back up to the proper fill parameters.
In addition, there are a few video links below that you may find helpful.
ruclips.net/video/5pwfHcBkvsU/видео.html
ruclips.net/video/nQGf8rf4F5s/видео.html
ruclips.net/video/CIRhyzDhqnE/видео.html
😎👍
@@DIYwithMichaelBorders thank you kindly I will keep following you are greatly appreciated 👍
@@kirkwalsh8239
That’s awesome, and thank you. We subscribed to you as well. 👍
I could argue there’s FAR more than 4 causes of an ABS malfunction. Caliper pistons, low brake fluid level/fluid leak, intermittent connectivity with either power or ground wires, low battery voltage, bent rims or fix-a-flat, the abs module might need re-calibration, bad MAF or MAP or crank or cam sensors….the list goes on and on and on…..it’s a sophisticated system.
Definitely, we appreciate you watching and sharing this. Any and all helpful info is greatly appreciated. 😎👍
“4 most COMMON”… if you are arguing which 4 were chosen, then specify that.
Otherwise work on your reading comprehension.
@@aaroncalhoun9825 technically you’re correct. I was trying to shed a light on the 4,000 other non-common causes of ABS malfunction.
Could you tell me why my ABS LIGHT CAME ON AFTER TAKING MY CAR IN FOR REPAIRS....THEY SAID THEY PUT ON A NEW SUPENSION RACK. PUT A FRONT GASKET ON......THEY ARGUE ITS MY WORD AGAINST THEIR MECHANIC.... MY LIGHT WASNT ON WHEN I TOOK IT IN
@@lajunecrockett2381 some ABS systems read sensors on the suspensions system as well. If that’s the case then every time the car is lifted off the ground the ABS light will turn on. Usually knowing which ABS code is causing the light to come on is the first step.
Thank You for the most common causes definitely will give it try ! 😎👍
You are welcome, we are happy to help. 😎👍
Greaat Great video........... I love youtube - SO educational. This Video was concise clear sooo helpful. Thank you to all you guys/gals for educating the rest of us.
Good morning, we really appreciate you sharing this kind comment. We love RUclips as well, definitely a great asset to DIYers.
😎👍
Most fuse / relay blocks have a fuse pulling / insertion tool tucked away somewhere. Hard tools can easily break the fuse. But a great, easy video to follow. Thanks
Good morning, we are drinking our morning coffee answering any and all questions for the DIY community.
You are spot on, thanks for sharing!
Much easier to use needle nose pliers, very carefully as stated. Those little tools don't always work they great - especially in tight quarters. Use what works best for you.
I have an 07 Trailblazer and I replace my steering angle sensor and hub bearings with abs cord, brake rotors and pads, and abs light and traction control light still comes on, you have any idea? Thanks for sharing your video..
Thanks for watching & welcome to the DIY Raptor Club. You may need to perform an ABS system reset. Below is a link to our video showing this process.
ruclips.net/video/Fu47rWAD30k/видео.html
Please keep us posted. 😎👍🔧🔩
My 2008 has anti lock esp and slip lights come on when o go over 15 miles per hour. I have watch your videos on causes.
How do I find out which wheel is making this happen? I noticed that I have a very slight vibration in my steering wheel could this mean I need to replace one of my rooters or the magnetic ring for my abs sensor
Thank you for your videos and help
Thanks for reaching out to us Mark & we appreciate you watching our videos. Do you have an OBD scanner?
If not, you come visit your local AutoZone and they can read your error codes for 100% free.
The codes will help pinpoint the exact wheel hub causing issue.
😎👍🔧🔩
Yes I am going this afternoon after work and they have a scanner that they can tell me what is going on for free
I will let you know what I find out
@@markpatterson7069
😎👍
I have Ford Focus showing 2 ABS sensor errors. Testing the plugs, 2 are 12v, 2 are 9v. The wire from ABS module to sensors are in tact and i tested they carry 12v. So the ABS module is outputting 9v. Is it likely the electrics in the Module or something else? Maybe fuse box?
Thanks for watching, it may be as simple as a reset. Below is a link.
ruclips.net/video/Fu47rWAD30k/видео.html
😎👍
Hi! Thank you for taking the time to share your knowledge of vehicle repair with the world. My ABS light has been on (steady) since I had my tires replaced 3wks ago, getting ready for winter. For two days, the the ABS activates, showing a car skidding icon (on completely dry asphalt here) and the gas pedal loses pressure. It activates every time I have to start it up (minimum of 6x daily) and today it happened while I was facing oncoming traffic. Can you please tell me which of the 4 reasons explains the issue my 07' Lincoln Navigator L is having? Thanks a bunch!
Thanks for watching & welcome to the DIY Raptor Club. Let’s get this figured out.
You mentioned tire service recently. Believe it or not, low tire pressure can trigger ABS light.
We recommend checking the sidewall of your tire for the proper psi and filling your tires to that psi.
Go for a test drive and see if this turns off your ABS. Keep us posted, us fellow DIY’ers need to stick together!
😎👍🔧🔩
I had a blow out on Tuesday. I ended up replacing all tires. I have the same issue that you described. The gas pedal acts up once when I start the vehicle, then it is OK the rest of the drive. Did you get it figured out?
@@BatmanVMMA
Thanks for watching & it’s very possible that your blown tire damaged an ABS sensor. We recommend having your ABS error codes read by an OBD scanner. This will help us pinpoint the exact part causing your issue.
AutoZone will read error codes for 100% free. 😎👍🔧🔩
@@BatmanVMMA please can you update this thread when you check the codes given. Currently in EXACTLY same situation. Blown tires > tires replaced > then ABS light.
@@charleseke7341 I used a code reader and there was a code. I think it was C0055 or something like that. The code reader told me the rear passenger tire speed sensor something something... I forgot exactly what it said, but I cleared it and it hasn't come back on. When I inspected the sensor, the blow out rubbed off some of the plastic coating on the wiring. I used some shrink wrap stuff on it. Hope this helps.
Thank you. Great video. My old honda odyssey recently showed an ABS light on along with other lights. After stopping at traffic light, my car won't accelerate when pressing the gas pedal. Do you think that would be the only problem? What would be the expected cost to repair each individual issue vs changing the whole ABS unit together? Here in CA prices can vary so much, price gouging is so common. I recently brought a 2013 escalade to the shop and they told me my rotor and axel in the back wheels have to be replaced, and I paid $6.5K for it. I am scared to bring my car to any mechanic worrying they are going to ask me to pay $2K for this issue.
might be the computer
Are those speed sensor rings on the 04 suburbans? I have a wheel locking up every time I plug my abs fuse back in...
Good morning, we are drinking our morning coffee answering any and all questions for the DIY community.
You may actually have a caliper in its early stages of failure. If calipers have not been changed in last 5-7 years, it’s very likely the caliper is the cause.
Please keep us posted, we DIYers need to stick together!
@@DIYwithMichaelBorders thank you for the advice I will try and replace it
@@DanielSilva-ko8zm
Looking forward to hearing back from you.
I had a ABS module replaced. They didn't use the scan tool to move valves in ABS module and properly get air out of lines when preforming brake bleed. So chased my tail figuring it out.
Thanks for watching and sharing this. Is everything back to normal and working properly after the repair and brake bleed?
Great video. Is it possible for the ABS moduel to go bad and need to be replaced without the need to replace the speed sensors or the exciter magnetic rings?
@@meshkatassian8946
Thanks for watching, definitely a possibility that we can’t rule out as a cause. 👍
@@DIYwithMichaelBorders.Mike Thanks for your reply. I need your help in understanding what is going on with my car and truly be thankful for your input.
I have a 2012 Hundai Sonota. A few weeks ago Bunch of engin lights including ABS light (intermittently) were coming on. I took it to a Hundai dealer to have it checked.
They told me this is electrical related issue and to diagnose the issue it will cost me $180. I agreed. After a few days their service called and said they have checked all the components that they thought could be causing this but haven't been able to pinpoint it and need to do further diagnostic work and it will cost me more money to do that. I agreed. After a few days they called and said they have determined the cause for this issue is a bad ABS moduel ...the cost will be 500 for diagnostic wk + $1300 to replace it. I agreed. I Had no other choice!!
They called me yesterday and said they have installed the new ABS moduel and all engin lights except for the ABS is gone. They said that they have checked everything and found one of the wheel sensor is messed up and it is likely that this is what has created the issue with the ABS moduel in the first place!!!
So they are replacing the bad wheel sensor as well.
Mike, at this point, I am having a hard time accepting the accuracy of their initial diagnosis and don't know what to do.
My question is can the messed up wheel sensor be the actual culprit to begin with and that the ABS moduel was never bad and didn't need to be replaced at all? Or can they both go bad? Or can a bad wheel sensor as they have told her damage the ABS moduel. Don't mechanic use an advanced OBD2 reader that can pinpoint weather it is ABS moduel or speed senors?
I feel like if the ABS was never faulty they should not be charging me the $1300 for replacing it and only charge me for replacing the bad wheel sensor. What do you think?
Also, if one wheel sensor is bad, should I replace all 4 sensors now.
@@meshkatassian8946
We are honored to help and that’s a bummer that you have had to experience this in recent days and weeks.
To answer your question, yes 100%!
It is 100% possible that a faulty wheel speed sensor can trigger the ABS light.
To answer your question further about if the speed sensor can be the original culprit while the ABS module still good…Yes, it is possible that your original ABS module was A-ok and not faulty however we can’t personally confirm that…but…it is more common for a speed sensor to fail and trigger the ABS light…as opposed to the module failing.
Hope this help. 🧰
Thanks Mike... It is so heart warming to get your input...
As I have said earlier, The shop is telling me that the ABS moduel was faulty that is why it was replaced. In addition they say that the messed up wheel sensor is what has caused the ABS moduel to go bad!!!
Mike, Can a bad wheel sensor as they have told me (damage) the ABS moduel?
Don't mechanic use an advanced OBD2 reader that can pinpoint whether it is ABS moduel or speed senors? Or both?
What can I asked the mechanics to show me to assure me that the original ABS moduel was indeed faulty and needed to be replaced?
I feel now that they have replaced the $1000 ABS moduel they are trying to justify their repair work by saying that the messed up sensor has damaged the moduel!!!
@@meshkatassian8946
Thanks for the reply, we are always happy to help.
Will a speed sensor ultimately cause an ABS module to fail…it’s possible…however we have never heard of that happening…🤔
We don’t know all the ins-and-outs of what the shop diagnosed and because of that…can’t give you a definite answer.
But again, we have never seen a wheel speed sensor being the sole pinpointed culprit of an ABS module failure.
🧰
Could I spray electronic contact cleaner then let it dry do you think that would do any good I'm a woman and trying to find the easiest route
Good morning ☕️ good question. We haven’t applied that in the past, can’t give you a confident answer.
The electrical connection points can be sprayed with WD-40 , WD stands for water dispersant .
Thanks for watching.
Hello. I have a 2014 Jeep Sahara with 7000 miles .I pressed the ESC button by accident when I was cleaning. The ABS light and ESC light came on. When I pulled away the left front wheel dragged and then released. This happens @ every start. What can I do. Thank you
John .
Thanks for watching & welcome to the DIY Raptor Club John. We would start by doing a Reset.
We recommend disconnecting the negative cable from your battery and leaving disconnected for a minimum of 30 minutes.
After 30 minutes, resecure negative cable to your battery and see if your system has reconfigured properly.
😎👍🔧🔩
Don’t forget about BUS problems! All sensors, fuses and modules can be good but a bus / electrical issue is always possible. Can test that issue through testing for power through you’re harness or splice packs!
Thanks for watching & sharing this Donald, any & all helpful info is greatly appreciated!!!
We really appreciate it. 😎👍
Ran into video and I’m in desperate need of advice. I’ve got a 2006 gmc savanna 3500 it’s not a van it’s a U-Haul truck I’ve been been through 3 transmission and every last one has gone bad. I did notice one thing when they put my 2nd one in my ABS and emergency light came on and my speedometer stop working it’s bottom out to 0mph there has been time where I’ve pass by a pot hold and it’ll trigger something and make it work again but it’ll only reach to 40mph and dye again. I’ve also notice that when the abs and the break light doesn’t appear on my dash the transmission shifts good my question to you is you think it’s the abs module? Can it trigger transmission to act up?
@@sanchezerick8377
Thanks for watching, any update? That’s a bummer you have been through two transmissions already and onto your third.
Hopefully the electrical wiring for your speedometer was not damaged during one of the transmission swaps.
It’s possible that it’s the ABS module however, unlikely…🤔
When was the last time you disconnected the black negative cable as well as the red positive cable and left disconnected for a minimum of 30 minutes? This will allow your system to perform a full reset.
would like to know why the u0401 and c056e codes are present and replaced the control module and the sensor under the truck reprogramed but still abs light and these codes
can you help
Thanks for watching & welcome to the DIY Raptor Club. This may sound funny however we recommend verifying all 4 of your tires have the proper psi in them.
We recommend filling them to the manufactures recommended max which can be found on the sidewall of your tires. By chance do you know when the last time your suspension was aligned buy a professional shop? Believe it or not, something so simple as unbalanced tires can trip your ABS system.
😎👍🔧🔩
Hi i.just ha d my honda fit replacement of rear wheel bearing and front axle assembly, we provided both parts,now when we pick up the car the eps and abs lights was on, another mechanic manuever the steering and looks like eps was off now but ABS lights still remains on
Thanks for watching & welcome to the DIY Raptor Club. Sounds like a friendly visit back to the shop that worked on your car is in the near future.
They should be able to reset your computer & will hopefully not charge you any $$. Keep us posted.
😎👍🔧🔩
Did you check the body ground connection for the ABS electronic module?
Good morning, just poured a cup of coffee and am sitting down to answer any and all questions for the DIY community.
All was secure throughout the system however great idea to verify. 😎👍
Let us know if you have any questions and hey if you’re into crypto trading, join our DIY ecosystem and become part of an exclusive group of DIYers.
toolboxtoken.com
Reach out to us any time! 🧰
"OH", one more question regarding the ABS module. I understand there is a way to "reprogram" them, "OR" Flash them and clear the internal code, "HENCE" clearing your light ?? Of course, you would need to find someone that can do it, as you might also need him in case you end up using a "Used" module, since they would need to programme module to your specific VIN and model vehicle?? Thank Again !! God Bless !
Great question & it’s very possible that the video link below will help. It’s a (Quick Reset) procedure that resets system. Your procedure may be different if your vehicle is not a GM/Chevy.
ruclips.net/video/Fu47rWAD30k/видео.html
😎👍🔧🔩
@@DIYwithMichaelBorders "NO" , sorry, just saw your video on the reset. And , "NO" , it's not a Chevy, we're talking 2002 Ford F-150. But so far , we have enough to at least start looking for what might be wrong, and "WHY" it is "Intermittent" ?? Thank You , God Bless !
@@curlyelp7530
So happy to help. 😎👍🔧🔩
How can you tell if it’s got moisture inside? It did rain off and on for a few days before the light came on. It literally came on after I got my tires balanced and rotated. Could they somehow have loosened this piece when removing the tire? That sounds plausible to me. Please help. Im stranded. 😢
We are happy to see you watched this video. When your tires were installed and balanced, it’s very possible that the technician slightly altered something within wheel well….possibly bumping the speed sensor and loosening the connection or even worse…damaging it…unlikely however it has happened to a few of our viewers.
To answer your question in regards to checking for moisture, you can carefully disconnect speed sensor connections inside wheel well and allow them to air-dry for a few hours.
Extremely wonderful camera work.
Hey Ted, thanks for sharing this, we do our best. Many more helpful videos to come! 😁👍
Wouldn't it be easier to check the fuses first since that is really quick? It would suck if you inspected all 4 wheels and then found out it was a blown fuse. Also, shouldn't you check the fuses electrically with an Ohm meter ?
Thanks for watching and sharing your thoughts. The order of inspections can be personal preference.
😎👍
I have a 2013 Ford E250 I replaced all 4 corners rotors and pads , works great but, now have ABS lights which come on for 10 miles then off, repeat. I had no lights before brake work 🤔I tried all your suggestions i e gas pedal 3 times etc. Had Advanced Auto check a couple times no codes 🤔 Help😰
Thanks for watching & it’s very possible that your fluid level is off. Check out the video link below, it may be helpful.
ruclips.net/video/X-AJ5tD6zoA/видео.html
Let’s start there. 😎👍🔧🔩
on a 2015 ford Escape, all wheel speed sensors are working fine and giving same reading, codes for ABS are C0061:54 and C0062:54 , and -2B lateral and longitudinal accelerations sensor. Is that pinpointing the ABS module itself is bad?
Good morning ☕️ any update? Let’s first perform a system reset. Below is a helpful video showing this process.
ruclips.net/video/Fu47rWAD30k/видео.htmlsi=N88A6XLerFDWX8pd
If that doesn’t work, we recommend disconnecting the black negative cable from your battery and leaving disconnected for a minimum of five minutes.
This will also reset your ABS system and hopefully reconfigure it back to normal working operation.
If both reset procedures fail, try them a second and third time as it may take a few resets to fully reconfigure your system.
Still, no luck…I t’s likely the module.
I have a 1995 E320 Mercedes Cabriolet convertible that has both the ABS and the ASR lights are on.
There are no error codes to reset even when you run an error code check reader. Took it to a
Mercedes dealer and they had it all day while I waited for the car. They were unable to fix it and
could not reset the error codes cause there aren't any. They also couldn't tell me what was wrong
with car, no charge either, still not fixed. After I got the car back I took the wheel sensors out and
cleaned them and the wheel spacers too, with no luck. What would you suggest?
Thanks for watching & welcome to the DIY Raptor Club. Any update?
We recommend checking inside speed sensor electrical connection point. Verify it is clean & dry...no moisture, no rust or corrosion...& definitely no signs of over-applied dielectric grease...that can cause all kinds of issues.
Double check your fuse box to ensure any and all fuses related to your ABS system are properly secured and have no moisture or corrosion on the leads.
Let’s start there, keep us posted. Let’s get this figured out. Us fellow DIY’ers need to stick together!
@@DIYwithMichaelBorders Thank you for your reply. All of the fuses were replaced
with the copper ones the original ones as you know were aluminum. There is no
separate fuse listed on the fuse box diagram either. I thought of replacing just the
wheel sensor wiring but they are no longer available from Mercedes, and no after
market either. Now what?
@@bobjohnson8206
Thanks for the reply. You may need to purchase an aftermarket part.
😎👍🔧🔩
@@DIYwithMichaelBorders I wish I could there is none.
@@bobjohnson8206
Thanks for the reply. Do you have an OEM part #? We can try to help look up options.
😎👍🔧🔩
Hi I have a holden captiva which I replaced the abs module due to dealer scanned it and said will need to replace so I used 2nd hand one just wondering as the abs lights are still on will it need to be reset or programed ?
Good morning ☕️
Awesome job making it a DIY project. A reset procedure is recommended, and it may be as simple as just disconnecting the black negative cable from your battery and leaving it disconnected for a minimum of five minutes. 👍🧰
Can you tell if the magnetic ring should have magnets all around the ring? Because I replace the ABS sensor and watch that ring but it only had a few magnets... very good video by the way!
Thanks for watching & welcome to the DIY Raptor Club. This will depend on the vehicle however almost all designs are of the ring magnet method.
By chance have you had your vehicle hooked up to an OBD scanner to read your ABS codes? This will allow us to pinpoint the exact part that’s causing your ABS light to come on.
In most cases, your local AutoZone will read your codes for 100% free. Please keep us posted. Us fellow DIY’ers need to stick together!
😎👍🔧🔩
Hi, Is I disconnect the connector on my original abs module, and then I reconnect the connector for only cleaning contacts on the abs module must I reprogramming with vcds or not ?
@@massimopica5008
Thanks for watching, some model vehicles will require it however not all.
Try disconnecting the black negative cable from your battery and leaving disconnected for a minimum of five minutes. This will allow your system to perform a reset and likely reconfigure your ABS system and sensors to the main onboard computer of the engine.
I do have an 1994 Olds Cutlass Supreme S 3.1 & my ABS light does come on & done the RESET which I seen ,but all it does is to lock the doors,however when I put the car in drive that's when it'll come on again
Good morning, just poured a ☕️ and am sitting down to answer any and all questions for the DIY community.
We are honored you took the time to share your experience. Since your vehicle is doing that, it’s likely that there is a part within the ABS system that is faulty. May need to have your ABS system checked for fault codes.
Let us know if you have any questions and hey if you’re interested, join our DIY ecosystem and help us grow an exclusive group of DIYers.
toolboxtoken.com
Reach out to us any time! 🧰
Mine was that a wire got cut off while jacking up a tire…if this happens to your after fixing a tire just check for cut wire behind that tire
Thanks for sharing this, that’s interesting, and awesome job pinpointing that to be the cause.
😎👍
Thank you for this video.
I have a unique problem that has stumped 3 mechanics and at least 2 really good computer coders..
My truck (2008 Chevy Express 1500 Cargo Van) had a problem that was traced to the throttle body harness. It was crimped. Replaced and 4 new tire sensors as well.
Problem I experienced was check engine light and van putt'd & sputtered. Towed to mechanic and above fixes.
Since then (3 months) intermittent ABS/Emergency brake light comes on and stays on for either a couple hours or all day. I have since noticed the check engine light periodically coming on at the same time. It eventually goes out, as do the other 2 lights.
Today, I had to be towed. The van was showing signs of putt'n & sputtering while sitting idle. All the lights mentioned were on. My last stop I noticed the van felt as if it wanted to surge slightly while in gear and brakes applied. The speedometer was fluctuating up and down as well. Once under power the check engine light started flashing and I lost power. After shutting engine off and starting again...check engine light solid. Once under power for less than 1 minute...check engine light began flashing and loss of power.
Mechanic is stumped. Any chance you've encountered this situation?
Kim D.
Did you ever find out the problem because mine doing it right now...
Hi. i have an abs esp fault. i have had it plugged into a computer and the fault says front right speed sensor.
I replaced this, check the wiring for freys. also i replaced the full hub. fuses too.
unfortunately the fault still comes on? it's intermittent
Thanks for watching & welcome to the DIY Raptor Club. Try this reset procedure below.
ruclips.net/video/Fu47rWAD30k/видео.html
Keep us posted. 😎👍🔧🔩
Thanks for the great video. I have the same problem with Cadillac Escalade ESV 2016.in raining, few lights get ON, traction, ABS,and the steering gets harder even undeliverable. Do you think these are the same issue and can be fixed by changing sensors?
Good morning & welcome to the DIY Raptor Club. We recommend starting with the fuses. Check to ensure all fuses related to ABS system are clean, not rusted or corroded, as well as the fuse box internal leads that fuses connect into are clean, dry, & not melted or damaged.
If all looks good, it’s time to direct attention to the sensor. Let’s start there. Please keep us posted, us fellow DIY’ers need to stick together!
😎👍🔧🔩
Thanks, I have the same problem, I try to same technical
Really appreciate your knowledge 50yrs worth that is wisdom many thanks
Thanks for watching & good morning, we are drinking our morning coffee answering any and all questions for the DIY community.
That’s very kind of you to share Frank. We are always here to help answer questions, enjoy your weekend.
😎👍
ABS light on my 1987 Vette is now on after the mechanic installed new front brakes due to it jerking to the left when braking. This did not correct the problem. He said the ABS system was bad. I found a used one on eBay. This still didn’t solve the problem. The light is still on.and the ABS is not working. Any input from you is appreciated.
Richard Dorsch
Thanks for watching Richard. Has the new ABS system arrived and been installed?
😎👍🔧🔩
Can I ask which one of these 4 could cause my truck to jerk after braking?
Thanks for watching, any update on your findings…?
It’s likely that you have a damaged caliper and piston. It’s also likely that you have an electrical issue within your ABS module.
Looking forward to hearing back from you.
You must be in area that the roads are salt treated. Outside truck looks great but undercarriage looks bad. Appreciate the video.
Thanks for watching & the winter is upon us. Let us know if you have any questions. Us fellow DIY’ers need to stick together.
😎👍🔧🔩
All 4 brakes and rotors were replaced on the car. Neither the ABS or Traction Control lights were on before they were replaced by the shop. I tried to do the quick reset, but that didn't work. Any ideas, I checked the first 3 common causes from this video and then all looked good. Thanks
Thanks for watching & we appreciate you sharing this. That’s no fun. We have attached a quick DIY reset procedure that may help... it’s possible that it’s the same reset procedure that the shop did.
ruclips.net/video/Fu47rWAD30k/видео.html
If this does not work, you may want to disconnect the black negative terminal to your battery and leave disconnected for a minimum of 30 minutes. This will allow your system to complete a full reset.
After 30 minutes, re-secure cable to battery and see if your error codes are no longer illuminated.
😎👍🔧🔩
I turned off my car after getting 4 lights on it and when i turned it back on all the lights were gone (including abs). Could rain cause something like this to happen?
Thanks for watching, rain can definitely lead to trapped moisture inside a wheel speed sensor.
That’s up there with the top common cause issue that triggers ABS light to illuminate.
2008 jeep liberty my asb light comes on randomly and takes over my car. I can pull over and hold down the dash millage button and it resets. But the not knowing costs money, anyone can take advantage. Can you see the problem with the computer?
Thanks for watching Dennis & welcome to the DIY Raptor Club. Let’s get this figured out.
Let’s first start with a system reset. Below is a link that will guide you through a System Reset. If it works...great...if not, onto the next option.
ruclips.net/video/Fu47rWAD30k/видео.html
Again, if reset does not work...&...since your ABS light comes on, we recommend visiting your local AutoZone where they can hook up an OBD scanner to your vehicle and read your onboard computer ABS codes.
The error codes will help pinpoint the exact part causing the issue. Please keep us posted Dennis. Us fellow DIY’ers need to stick together!
😎👍🔧🔩
@@DIYwithMichaelBorders headed there now, thx.
@@dennislurvey3235
😎👍🔧🔩
ABS Light on and empty brake fluid reservoir .. Looking for a leak now ?
@@bluemoon3264
Thanks for watching, any update? Let us know if you have any questions.
I have a 03 Ford Expedition. I'm currently trying to diagnose a brake issue. My vehicles calipers on both the driver and passengers side are severely sticking. Would that be an issue with the abs pump or the master or both?
Good morning, we appreciate you sharing this. Us fellow DIY’ers need to stick together! It’s unlikely that it’s a faulty Master Brake Cylinder (MBC) however we can’t rule it out.
Have you performed any recent maintenance on your brake system in the last few months? This will help us pinpoint whether or not any recent maintenance is tied to your issues.
Keep us posted, welcome to the DIY Raptor Club, hope all is well.
😎👍🔧🔩
@@DIYwithMichaelBorders it was the abs pump. I acquired the vehicle from a friend and they did some maintenance on it trying to figure out an issue several years ago.
It turns out the abs fuses were missing.
@@TherealWinterpillow
Very cool & we appreciate you sharing this update. Back up & running is a great thing. Hopefully many stress free days ahead for you.
😎👍🔧🔩
My abs light went on other day, I pulled into a parking spot but my from wheel grinded, then didn’t after I stepped the brake. Pads are good, rotors are good, bearing I never had a problem with it, no noise or vibration and always drove straight. I’m hoping it’s just the abs sensor and the grinding abs attempting to hold up
Thanks for watching & welcome to the DIY Raptor Club. By chance is your ABS light illuminated at the moment?
If yes, we recommend hooking an OBD scanner up to your engine to read the ABS fault code. This will help pinpoint the exact part causing your issues.
AutoZone hooks OBD scanner to your vehicle and reads your fault codes for free. Please keep us posted.
😎👍🔧🔩
Hello, thanks for this video🙏. My car is SATURN 2007 and today I see ABS light ON , time to time my I see TRACK OFF on the DASH, please tell me what I can do!
Thanks for watching, any update? Below is a reset procedure that may help reconfigure your ABS system.
ruclips.net/video/Fu47rWAD30k/видео.htmlsi=v8okjdlphwVSe91G
🧰
Can I remove the ABS Fuses, Thus disabling the ABS System & Lights and function regularly?
Thanks for watching, unfortunately that will begin to trigger many additional fault codes that will lead you to think additional parts have failed when they are still working…leading to components degrading and lessening the overall performance/reliability of vehicle.
Are you having trouble finding replacement fuses?
Thanks, I just want the warning lights OFF
Great video. Based on comments here and elsewhere, it seems almost inevitable a mechanic or dealership tells you it is the module, big ticket item which is the problem. You want to get a kick? Next time you talk to the guy at the service desk, work into the conversation how you have researched your problem on YT and then look at their reaction. It's facial because they don't respond verbally.
Good morning ☕️ thank you for sharing your thoughts. 😁👍
Haven’t read all the comments but my 2010 Prius has an error code 1391 Abnormal leak off acc press.
Toyota had a voluntary recall I missed due to getting the car second hand. The repair is abt $3000 to replace the brake master cylinder and pump. Is the code definitive or should I consider the causes you mentioned in your video. All this happened after getting my brakes and or tires replaced
Thanks for watching, any update? Before doing anything, we recommend carefully disconnecting the black negative cable from your battery and leaving disconnected for a minimum of 30 minutes.
This will allow your entire system to fully reset. After 30 minutes, resecure black negative cable to battery and start engine to verify that the onboard computer and all electronic sensors that communicate with it have fully reset and reconfigured themselves properly.
This will hopefully save you $3000.00
😁👍🧰
@@DIYwithMichaelBorders Even if the brake feels squishy? I’ve reset the lights but they come back. I haven’t tried disconnecting the black cable as the car is now across the country. I can ask my brother to try your recommendation. Thanks!
@@seeingyouontube
Thanks for the reply, looking forward to hearing back from you. 👍
I had wheel barring put on on driver side.But ABS light came on after i got it fix.How do i reset it ABS light.Thank you.
Thanks for watching. Below is a helpful reset procedure video. Keep us posted.
ruclips.net/video/Fu47rWAD30k/видео.htmlsi=K2QgeuNXf-aafcl1
Let us know if you have any questions and hey if you’re into crypto trading, join our DIY ecosystem and become part of an exclusive group of DIYers.
toolboxtoken.com
Reach out to us any time! 🧰
Wow just have to say. Props for trying to help as many people as possible in the comments. Like wow you’re amazing dude. If you’re still answering questions, I have one.
So my car has had the traction light on for a bit, but sometimes when I’m driving, abs and break lights turn on. Also, my car just started moving the speed diameter up and down in the middle of driving. The car feels perfectly fine, but, kinda scare about this symptoms. Already took it too a shop, but they couldn’t fix the problem and I have nooo idea what it might be.
I am willing to pay for a abs module but idk if that’ll be the problem
Thanks for watching & welcome to the DIY Raptor Club. Let’s get this figured out. A few things to do.
1. Verify all 4 tire pressure reading are set to manufacturers recommended psi. Believe it or not, low tire pressure can trigger abs in newer modern vehicles.
2. If you live in snowy areas, snow, ice, water, & moisture can sneak into abs sensor electrical connection points. This leads to abs turning on. In this case, disconnecting electrical connection and cleaning/drying will hopefully help.
Let’s start there. 😎👍🔧🔩
@@DIYwithMichaelBorders thank you and yes. all tires are set to manufacturers specs. Also, idk when people say new because i have mostly owned old cars lol. The car having this problem is my 2012 Dodge Avenger and i live in Arizona where the lowest we get is 40F and a high of 118. So maybe the second step would be ruled out? or would you still recommend me checking it out?
Also have switched most of the fuses in the fuze box. Now, i didnt touch those big square fuzes found in the box (sorry dont know the mechanic lingo lol)
@@MooseX2012
Thanks for the reply & is your ABS light illuminated on instrument cluster? If yes, you may want to visit your local AutoZone & have then read your ABS error codes. They do this for free.
Obtaining the error codes will hopefully help pinpoint the part causing your issues.
so a month ago I did the annual servicing oil my chevy cruze and when I went to pick my car the ABS light was on and the pump kept running even after turning off the car
the car mechanic managed to turn the pump off but the ABS light is still on, I went to another mechanic he said the abs module need to be changed and today I showed my car to another mechanic he said the booster cylinder need to be changed but at this point I don't know if I should trust any of these mechanics any advice which route I should take?
FYI my car is 2013 chevy cruze 2.0 has ran only 52000km
Good morning & welcome to the DIY Raptor Club. Let’s get this figured out. 1st... we recommend visiting your local AutoZone where they can connect an OBD scanner to your vehicle and read the onboard fault codes.
If your ABS light is illuminated on your instrument cluster, the OBD scanner will be able to detect the fault code which in return will pinpoint the exact part causing the issue.
Let’s start there, keep us posted. 😎👍
@@DIYwithMichaelBorders thank u ill try that
@@izack367
😎👍🔧🔩
do you teach at a 10th grade or lower level?
just wondering cuz you have a very calming voice and tone that might've helped me learn math early on
and you take your time with the explanation and not stress me out like some other teachers used to do when i was in grade school
tranquil Nice
Thanks for watching & we really appreciate you reaching out to us. We do our best to be as precise and helpful as possible. 😀
Let us know if you have any questions. Us fellow DIY’ers need to stick together!
F
Lol
My mechanic said I needed an abs pump....so I got a used one and now my abs light is on....considering to put back my original abs pump to see if abs goes off......your take on it?....
Thanks for watching & sharing this. Before removing new part, we recommend performing a system reset.
This can be accomplished by removing the black negative cable from your battery and leaving disconnected for a minimum of 5 minutes.
After 5 minutes, resecure cable to battery and start engine. Please keep us posted.
😎👍🔧🔩
@@DIYwithMichaelBorders another mechanic did a scan and said abs pump.....like I said the first mechanic said I needed an abs pump and he put in a used one and now abs is on....considering to put back my original abs pump to turn off abs light.....light was never on before....
@@robmartin217
Thanks for the reply, might not be a bad idea...🤔
I just had to replace both wheel hubs and the rotors, pads, and calipers on my 08 Colorado and the ABS and Fault light are still on. How do I get them to go out or do they go out on their own after driving it?
Thanks for watching & welcome to the DIY Raptor Club. Below is a link to a video that shows removing pads & rotors.
ruclips.net/video/S0temq1xiQg/видео.html
We are removing the pads and rotors during a hub assembly replacement.
😎👍🔧🔩
I replacing my ABS control module due to a nasty leak. It's on a 2006 lexus IS350. Once replaced does it require a reprogramming process or is it just simple plug and play?
Hello, I have a 2005 Chevy Colorado, and I have a ABS fault, traction control fault, stability control fault, all going off and has shut down my traction control and ABS. I have checked the rings, replaced the sensors, cleaned all connectors, and checked fuses. I got the truck from my brother who has had problems with the abs and traction control ever since he bought the truck. He actually had wheels lock up on him driving down the highway, after replacing the sensors it was running fine, then when we were driving we noticed one wheel started dragging and the front right wheel started grabbing spirraticaly. We cleaned the rings and sensors and it stopped but then suddenly threw 3 faults and we can't figure out why, please help have no idea where to turn.
What can cause traction fault, abs and brake lights come on and then the heater fan speed stops, no blinkers hazard ,windows don't work ...any help will be appreciated..thanks
Thanks for watching & welcome to the DIY Raptor Club. The most common cause is a faulty speed/hub sensor.
If you live in an area where there is snow, slush, ice…wheel-well can accumulate lots of snow, slush, ice buildup & cause havoc on sensor... leading to all sorts of bells and whistle‘s going off on your instrument cluster.
Keep us posted on your project.
would anything be wrong with spraying contact cleaner into the contacts?
@@carlodonnell146
Thanks for watching, personal preference and may be beneficial.
🧰
Hello, thanks for the good video. Is it possible for the ABS module to work with only one speed sensor? Actually, I am a student and I want to present the operation of ABS with a single tire and a brake unit using a single speed sensor.
Thanks for watching and without the speed sensor, the ABS module will still communicate with the other wheel sensors and operate as designed.
Most vehicles will still have a built in safety feature that allows ABS to engage on all wheels however the one with faulty sensor will behave sporadically.
@@DIYwithMichaelBorders Actually, I have created a project with single wheel and break assembly, and demonstrated the ABS module on a board, normal break is okay but anti skid not working, so i am stuck now. I want to ask is it necessary for ABS module to get all four sensor inputs to operate? Or we can use single sensor, or can we divide the output of speed sensor to four inputs for ECU??
@@livetech4062
We appreciate the follow up. Below is a link that dives deeper into how the speed sensor operates in conjunction with the hub. Pretty unique design.
ruclips.net/video/8CRXheZ_72Y/видео.html
😎👍
I need to completely clean out my brake lines from contaminated fluid. I want to blow break cleaner through the lines but will it mess up my abs? What to do? On a 2004 civic, discovered daughter put power steering fluid in the master cylinder.
Thanks for watching & we appreciate you reaching out to us. You can purchase a flush kit at your local AutoZone which will come with directions on how to properly flush system as well as doing it in a way that protects your ABS system. You may want to contact them & ask if they have one in stock prior to driving there. Keep us posted.
😎👍🔧🔩