Good job, nicely done. I like to see so many people doing hydrogen tests. I also made a few hydrogen generators, the problem is that I don't have much time for that. good video, i love hydrogen ❤️👍🏼
The residue on the plates is due to the use of brass bolts is simply made a galvanic reaction (the chemical added will support this further). Use stainless steel in all parts and get rid of residue + rust/oxidation. Btw..a flame arrestor would be a must-have safety feature. I almost wanted to say "Happy new year" as you melted the nail.. You can fabricate one by yourself a tube and some stainless steel wool is all it takes to be safe. Nice generator setup.
How much current does a setup like this take? Could you run a unit like this in a car off an alternator and inject it into the intake so it would actually give you a positive result in energy used vs created?
i guess im asking randomly but does any of you know a method to get back into an instagram account? I was dumb lost my account password. I love any assistance you can give me.
@Sonny Daniel Thanks for your reply. I found the site thru google and Im waiting for the hacking stuff now. Seems to take a while so I will get back to you later with my results.
That's a neat generator! How long can you run that generator for till you need to fill it up again? And do you know what temperature the generator operates at?
How do you avoid explosions? I have a second container where hydroxy rises in and to a tube. When i lit my torch which was a tube and a needle, it blew the lid off the jar.
A suggestion, use a striker for lighting the flame, I have seen people use small lighters to fire up torches before and the lighter blow up in their hand because the flame ran down into the fuel, or the flame melted a hole in the lighter.
each side of the neutral plates become opposite polarity ,the further away from one polarity you go,the more closer to the other polarity it becomes,it gives in essence more little + and - cells,from the most negative end each neutral plate face will become negative or positive,so one face of a neutral plate will be more negative or positive than the other side of the same plate -,+-,+-,+-,+ this would be negative supply at one end then three neutral plates then the positive supply at the far end,as Do R/C! says,voltage dividers,they even out and share the potential(voltage).
Is the cell itself heating in normal usage? I wonder what is the efficiency of the cell.. If the PSU supplies for example 500W, is 400W transferred for heating the water and 100W for producing HHO?
I'm curious as to what this style of drycell hho generator is capable of yielding, and at what voltage & amperage level? Also, is this solely the only type of application you use this generator for?
Excelente vìdeo , dos pregunta te marca alguna resistencia la celda de positivo a negativo y que espesor tienen los separadores entre las placas , gracias por compartir
Called a flashback, all the hydrogen in line line is exploding, thats why we have the bubbler. If there was nothing stopping the hydrogen from flashing back into the main container it would blow it self up.
I dont think these are "full" flashbacks though(probably just inside the torch) since a flashback all the way to the bubbler would make your ears ring and probably blow some tubes off their connections.
you probably explained this in a previous video, but how do the plates stay immersed in water? most models ive seen built involve the plates being in a tank of water where as here you just have a pump going
questions adding sodium or pottasium does it affect the quallity of oxygen ? can u breath it ? does actually make someone feel "better" breathing just oxygen ? what about hydrogen ? what happens to the hydrogen coming out of the electrolysis ? where it goes ? in order to make the blowtorch u make a small tip at the end so oxygen comes out at higher speed ?
omg i havent watched your channel in 2 years, i remember the dry ice rhnb being the first video i watched. it was in the trending or the home feed i cant remember.
So I guess the safety bubbler thingie is for when the flame burns back though the tubing it cannot reach the generator and blow it up. Is that correct? How thick are the cables which connect the generator to the power supply (the cross section I mean)? Is there any particular reason to use destilled water and add things to make it conductive, rather than using regular tap water? Will regular cooking salt work? If not: Where do you buy the chemicals? How expensive is the generator + tubing + water tank? Thank you for this interesting video. I would like to try this too. Are there any special/unexpected safety concerns (other than the gas being highly flammable because it contains oxygen)? Also: Does the torch tip have any special valves in it which prevent the flame from going back into the tube? Or is it just the gas coming out fast enough?
Don't use table salt it will produce a poisonous gas called Chlorine gas. use baking soda. Also use stainless steel plates and bolts. Also put the plates in this order + - + - and so on and so forth. Use household cable that goes in your walls. And yes the flash back erstor is to prevent flash backs from happening which is when the fire comes inside the tube.
Good afternoon, your generator is magnificent, what possibility is there to have detailed information to mount the system in the kitchen to replace the gas
You have your holes at same place so your plates can't create so much that way. It's better to have first plate 2-3 holes at the bottom and next plate 3 holes on left side, next 3 holes on right side etc until last plate where the exit is and have 3-4 holes at top to get best effect out of everything. I use 22 plates, size 150mm x 150mm and gives me plenty of HHO.
Distilled water doesn't conduct. It's the minerals and impurities that make water conductive. He's just using the least corrosive means to make the water it's most conductive. Could use salt water but it creates corrosion. It all depends on what your tap water has in it. More than likely you have hard water that will work just fine or even better but then you have the corrosion and calcium scale build up on the plates.
Probably not as well due to the extra unknown-containments that he can't possibly account for. Adding a verified amount of a substance would allow him to produce Hydrogen and Oxygen at a rate he could control, unlike with tap water which can change time to time. :)
i am not very good with this concept as this is my first time watching HHO stuff. what do the neutral plates do? 1 positive plate in the middle and 1 each negative plate at the ends and a bunch of neutral plates in the middle. i dont understand this setup. whats the purpose of the neutral plates between the + and - plates? thanks
This (HIPER-VOLTIC-HHO) reactor can be serviced while running. Close lower valve remove lower reservoir empty AND replace. Open valve add (HV) premix to upper resivour, check again in 60 hours repeat if needed
can we use this method for alterantive solution of bike fuel, while spliting the hydrogen from water and use hydrogen as a fuel for bike may it works, sugess me to do a project on this
Sir could you help me out i have steel plate 202 and of 3 inch diameter so how much positive and negative plates i add to get optimum result and water no heated
next time bro try to focus on the camera the outcome gas results... i saw only water bubbling didn't saw the ouput gas... anyway so amazing bro you did and excellent job... I would like to ask you if i could convert this gas into cooking gas just like gas stove?
havent had to clean mine since I bought it 3 years ago.. thing is... the plates arent just normal stainless.. they're 316L grade stainless... which is the most resistant to grain boundary carbide precipitation.. aka the leaching of iron into you water.. I also use 9x distilled water so it has no mineral's or elements in it either. still looks like when I bought it.
Hello Sir. Does this system that you made, DOES it SEPARATE the hydrogen and oxygen gases? In other words, the gases come out separately from the generator or do they separate on the plates but come out together through the same outlet? Thank you very much for your reply.
Наука
I've been waiting for years... for the build... but the build/rebuild is good enough!
Woooow!!! is incredible and amazing, congratulaciones friend, saludos desde cuautla México!
Good job, nicely done. I like to see so many people doing hydrogen tests. I also made a few hydrogen generators, the problem is that I don't have much time for that. good video, i love hydrogen ❤️👍🏼
Satisfying to see it cleaned.
Very Satisfying.
Excellently made and nicely videographed ! congrats !
Very well made HHO generator. Mine is way smaller but longer though to keep the production rate up while still fitting in an old toolbox.
That audio was amazing, keep it up!
felicidades!!! cuanto voltage le aplicaste y cuantos ampers!!!
I think this is really cool! You definitely have my support
I've been waiting for this for so long.
I remember a long time ago that carsandwater talked about finally showing us the set up of his Hydrogen/Oxygen Generator so he could clean it.
i use sparkle toilet bowl cleaner, cleans that brown goop off fast
The residue on the plates is due to the use of brass bolts is simply made a galvanic reaction (the chemical added will support this further). Use stainless steel in all parts and get rid of residue + rust/oxidation.
Btw..a flame arrestor would be a must-have safety feature. I almost wanted to say "Happy new year" as you melted the nail..
You can fabricate one by yourself a tube and some stainless steel wool is all it takes to be safe.
Nice generator setup.
Beautiful video I like your project thank you for sharing
sometimes I think this channel could pass off as ASMR
👍🏼
How much current does a setup like this take? Could you run a unit like this in a car off an alternator and inject it into the intake so it would actually give you a positive result in energy used vs created?
I have a question, does the generador heats up fast? Or for how long it can be running? Awesome vídeo.
He cleaned those screws really well
Thank you for your nice video and i will do this project, i understand 100% your video. Thanks Be To God.
man i remember when he first built this thing and now it's awesome to see it all fresh and clean again :D
i guess im asking randomly but does any of you know a method to get back into an instagram account?
I was dumb lost my account password. I love any assistance you can give me.
@Zayn Archer Instablaster ;)
@Sonny Daniel Thanks for your reply. I found the site thru google and Im waiting for the hacking stuff now.
Seems to take a while so I will get back to you later with my results.
@Sonny Daniel It did the trick and I now got access to my account again. I am so happy!
Thanks so much, you saved my account !
@Zayn Archer you are welcome xD
That's a really awesome design
That's a neat generator! How long can you run that generator for till you need to fill it up again? And do you know what temperature the generator operates at?
Muy bueno tu video desde Chile muchas gracias
Hey i got one of those! mines store bought. looks just like yours though! good job
are the plate sizes and thicknesses critical? What are the dimensions you used?
How do you avoid explosions? I have a second container where hydroxy rises in and to a tube. When i lit my torch which was a tube and a needle, it blew the lid off the jar.
What's the thickness of the PVC liner do you use? I think I saw it. Its 40 mil pvc liner from Homedepot, great!
Wow very helpful! How much power do you supply through it?
Hello.
Thats awesome!👍
Can i ask, why the neutral plates? Whats the purpose of these?.
Best regards,
T
Have you tried to weld aluminum? Is it ok to use it for aluminum welding?
I wanna ask if you have fire arrestor or any kind of protection ?
Can't wait to build one myself!
A suggestion, use a striker for lighting the flame, I have seen people use small lighters to fire up torches before and the lighter blow up in their hand because the flame ran down into the fuel, or the flame melted a hole in the lighter.
Im sure this is a stupid question but what is the purpose of the neutral plates on the system?
Nevermind. They are used as votage dividers..
each side of the neutral plates become opposite polarity ,the further away from one polarity you go,the more closer to the other polarity it becomes,it gives in essence more little + and - cells,from the most negative end each neutral plate face will become negative or positive,so one face of a neutral plate will be more negative or positive than the other side of the same plate -,+-,+-,+-,+ this would be negative supply at one end then three neutral plates then the positive supply at the far end,as Do R/C! says,voltage dividers,they even out and share the potential(voltage).
Thanks for sharing. Great video.
wow nice I've always wondered how to make one of these and know I have one :) thank you
Is the cell itself heating in normal usage? I wonder what is the efficiency of the cell..
If the PSU supplies for example 500W, is 400W transferred for heating the water and 100W for producing HHO?
mines running just luke warm 12volts at 7 amps... its a + N N N N N - rig
Great walkthrough! But... 5 neutral plates means 6 gaps. 2.3V between each plate, yes?
You're right! My mistake, thanks for catching that :)
+carsandwater do a face reveal
he has videos with his face in them
+TexasSmoking Jesus that was the fastest homophobic response I've ever seen for a RUclips comment, that was literally less than a minute
+joyfullalmonds Now let's talk about religion and make parallels involving the nazis...
WOW !! you are the best man.!
I'm curious as to what this style of drycell hho generator is capable of yielding, and at what voltage & amperage level? Also, is this solely the only type of application you use this generator for?
Excelente vìdeo , dos pregunta te marca alguna resistencia la celda de positivo a negativo y que espesor tienen los separadores entre las placas , gracias por compartir
What are those pops when you were melting the nail?
Called a flashback, all the hydrogen in line line is exploding, thats why we have the bubbler. If there was nothing stopping the hydrogen from flashing back into the main container it would blow it self up.
popcorn
sounds like electrical arcs
I dont think these are "full" flashbacks though(probably just inside the torch) since a flashback all the way to the bubbler would make your ears ring and probably blow some tubes off their connections.
It's impurities in the steel nail. The nails had a little bit a rust on it so it was probably the small amounts of Iron-Oxide (rust) that was popping
Do you have to replace the metal that causes oxidation?
Bravo, sincèrement!
you probably explained this in a previous video, but how do the plates stay immersed in water? most models ive seen built involve the plates being in a tank of water where as here you just have a pump going
Ciao ottimo video. Posso chiedere perchè è meglio usare delle placche neutre anziche polarizzarle tutte? Grazie
questions
adding sodium or pottasium does it affect the quallity of oxygen ? can u breath it ? does actually make someone feel "better" breathing just oxygen ?
what about hydrogen ? what happens to the hydrogen coming out of the electrolysis ? where it goes ?
in order to make the blowtorch u make a small tip at the end so oxygen comes out at higher speed ?
Have you tried to weld some metalls with it? Is it good to use it for aluminum or steel welding?
Tigran Ohanyan *brazing
Nice video. Where did you get the white plastic material?
Hello, great job, you are the best, Tell me, What voltage and amperage do you use?
Where did you purchase the nozzle at the end?
omg i havent watched your channel in 2 years, i remember the dry ice rhnb being the first video i watched. it was in the trending or the home feed i cant remember.
Very interesting how this works. Detailed video of how it's made and how it works?
Like how much tubing, how many bolts, dimensions etc.
How often do you need to rebuild them?
Im curious if the brass is leaving the stains
Excellent works, Very good.
So I guess the safety bubbler thingie is for when the flame burns back though the tubing it cannot reach the generator and blow it up. Is that correct?
How thick are the cables which connect the generator to the power supply (the cross section I mean)?
Is there any particular reason to use destilled water and add things to make it conductive, rather than using regular tap water?
Will regular cooking salt work? If not: Where do you buy the chemicals?
How expensive is the generator + tubing + water tank?
Thank you for this interesting video. I would like to try this too. Are there any special/unexpected safety concerns (other than the gas being highly flammable because it contains oxygen)? Also: Does the torch tip have any special valves in it which prevent the flame from going back into the tube? Or is it just the gas coming out fast enough?
If you dont understand these basic things you asked about i would strongly suggest NOT building one.
Don't use table salt it will produce a poisonous gas called Chlorine gas. use baking soda. Also use stainless steel plates and bolts. Also put the plates in this order + - + - and so on and so forth. Use household cable that goes in your walls. And yes the flash back erstor is to prevent flash backs from happening which is when the fire comes inside the tube.
10 cup / plates is about 100$ in total.
Tap water will work but it may produce chlorine gas so that is why you use distilled or filtered water with baking soda.
Also four more questions that you want to be answered go to Anthony Tesla Arcs he'll probably answer it.
What is the benefit of neutral pallets?
Can you separate the gases H and O for a safety use with this eletrolyser?
Good afternoon, your generator is magnificent, what possibility is there to have detailed information to mount the system in the kitchen to replace the gas
You have your holes at same place so your plates can't create so much that way. It's better to have first plate 2-3 holes at the bottom and next plate 3 holes on left side, next 3 holes on right side etc until last plate where the exit is and have 3-4 holes at top to get best effect out of everything. I use 22 plates, size 150mm x 150mm and gives me plenty of HHO.
what is that gasket material ? Ps: I Want Hydro splitter To Get Pure Hydrogen :) already got a complicated plan for it
eto vce xuynya
about how fast is the flow of hydrogen with what you have set up now?
Hi Sir
Can you please let me know the voltage and ampherage you have used for power supply and the size and thickness you have used for the plates.
What purpose do the neutral plates serve? do they just add space for the water to build up in or do they do something else?
they add volume.. for more water
how well will it function with normal tap water ? Compared to your solution.
Distilled water doesn't conduct. It's the minerals and impurities that make water conductive. He's just using the least corrosive means to make the water it's most conductive. Could use salt water but it creates corrosion. It all depends on what your tap water has in it. More than likely you have hard water that will work just fine or even better but then you have the corrosion and calcium scale build up on the plates.
so it will just have to be cleaned and have som parts swapped out more often.
Probably not as well due to the extra unknown-containments that he can't possibly account for. Adding a verified amount of a substance would allow him to produce Hydrogen and Oxygen at a rate he could control, unlike with tap water which can change time to time. :)
It would be OK at first but soon clog up with contaminants and get very dirty very quickly.
+Joey Bartlett انت في قرقر كتير اني بورلي
hi! what thickness are the gasket and steel??
Hi. What is the function of the membrane covering the electrode?
Was the loud knocking noise when you melted the nail flashbacks?
i use sparkle toilet cleaner to clean the plates. does it real fast, dip the plate in and wipe off
Is it just pure lye?
and don’t lye to me!
2:18 Be careful grinding that. It's possible that the stainless can create some chromates which are strongly carcinogenic.
i am not very good with this concept as this is my first time watching HHO stuff. what do the neutral plates do? 1 positive plate in the middle and 1 each negative plate at the ends and a bunch of neutral plates in the middle. i dont understand this setup. whats the purpose of the neutral plates between the + and - plates? thanks
very nice friend please make and show hydrogen cylinder for any engine and work
Super cool video.
Thanks
A flash back arrestor from BOC was the last time i checked around £30
This (HIPER-VOLTIC-HHO) reactor can be serviced while running. Close lower valve remove lower reservoir empty AND replace. Open valve add (HV) premix to upper resivour, check again in 60 hours repeat if needed
what is HV ?
@@davelawson2564 HIPER voltic=purest balanced mixture of hydrogen 2 oxygen 1 that can be made on demand
@@michaelarcher9201 Obvious question . what is cost of power for generating 1 kg of this mixture ?
where u buy the plastic fittings ??
can we use this method for alterantive solution of bike fuel, while spliting the hydrogen from water and use hydrogen as a fuel for bike may it works, sugess me to do a project on this
What is the exact function of the safety bubbler?
hi, a question is why many neutral plates?
To achieve the 1.5 to 3v between plates which is the most efficient voltage range.
hi, the power that you use is 50 V 15 amps or 50 amps 15 V???
Sir could you help me out i have steel plate 202 and of 3 inch diameter so how much positive and negative plates i add to get optimum result and water no heated
next time bro try to focus on the camera the outcome gas results... i saw only water bubbling didn't saw the ouput gas... anyway so amazing bro you did and excellent job... I would like to ask you if i could convert this gas into cooking gas just like gas stove?
What power supply are you using?
Today I learned that nails are actually sparklers in disguise.
do you have an email where i could ask a few questions or possibly chat. thanks
Good video, I didn't see a flashback arrestor
Are those pops related to that?
Whats the popping noise when your melting the nail?
HAPPY BIRTHDAY!
Where/how can I get the gaskets that serve as spacers? Can they be custom-fitted?
I have a question how much gasket thickness
?
How long does it take to make it in that state?
Do you put something like water betwen these plates or what ??? i don't understand how it works ..
havent had to clean mine since I bought it 3 years ago.. thing is... the plates arent just normal stainless.. they're 316L grade stainless... which is the most resistant to grain boundary carbide precipitation.. aka the leaching of iron into you water..
I also use 9x distilled water so it has no mineral's or elements in it either. still looks like when I bought it.
what is 9x distilled water ? And how many hours have you run it ? what do you use the hho gas for ?
One smart man.
Your neighbors must love you.
Hello Sir. Does this system that you made, DOES it SEPARATE the hydrogen and oxygen gases? In other words, the gases come out separately from the generator or do they separate on the plates but come out together through the same outlet? Thank you very much for your reply.
they come out together from the generator, but do not react with each other until they are lit by the flame
what was that grey plastic film that said 40 MIL?
Are all the plates connected to the system ?
Nice video and good job
Motorbike runs on water | HHO | hydrogen gas generator | without petrol | with proof
#Raselhomemadecreator
I didn't know it was that easy to extract those elements from a compound o-o