Probably not immediately, but the option is there down the line if you want to swap. Other sticks dont give you this freedom. Dual modded PCB so it works on PS3/360 already. Cheaper just to buy a sanwa stick ($20) and throw it in, than to spend hundreds on a full new chassis etc
how can you tell the usb cable is not high quality? i own the omni and the cable has never bothered me. infact, its one of the better cables i have come across since it works without problems on ps3/360/pc.
i can tell, because i have a stick with the same pcb and the same usb cable. the isolation is like putty, take care to never run it over with an office chair or so, its just too thin and flimsy. for a high quality usb cable, look at e.g. the gamepads razer makes. i just find it dumb, that they wouldnt install lets say a quick release usb connection that is like 2$ per stick in production and would make it look of so much higher quality, that they could get away with a 230$ pricetag.
very nice m8 :) is it any good? u using circular gate? I ve a mad catz with square gate atm. But i send it back and will get a circular gate. Because my movement seems to be bad on a square. Is it a big diffrence?
because noobs like me thought that circular gates were better at first before we did the research and realized that square gates are better and we don't wanna buy another etokki
I bought the etokki because of its design, sturdyness and ability to house whatever kind of hardware. i am free to try out both japanese and korean levers without having to buy a completely new case. Its pretty obvious, dumbo.
Probably not immediately, but the option is there down the line if you want to swap. Other sticks dont give you this freedom. Dual modded PCB so it works on PS3/360 already. Cheaper just to buy a sanwa stick ($20) and throw it in, than to spend hundreds on a full new chassis etc
how can you tell the usb cable is not high quality? i own the omni and the cable has never bothered me. infact, its one of the better cables i have come across since it works without problems on ps3/360/pc.
they didnt even use a better looking/higher quality usb cable on that cheap paewang pcb ... and its a 200$ stick...
Where do I have to sodder the only groung wire that comes eith the sanwa? You said that you think they are all connected, but are you sure?
The proper way would be using connectors for the sanwa too, not soldering each cable on the pcb lol
They have a 5pin to qd converter, do you just take the wires from the pcb and they fit into the qd end???
Do I have to remove the plexy for Sanwa buttons to fit? Also will those pin connectors fit on Sanwa's?
i can tell, because i have a stick with the same pcb and the same usb cable. the isolation is like putty, take care to never run it over with an office chair or so, its just too thin and flimsy. for a high quality usb cable, look at e.g. the gamepads razer makes. i just find it dumb, that they wouldnt install lets say a quick release usb connection that is like 2$ per stick in production and would make it look of so much higher quality, that they could get away with a 230$ pricetag.
soooo..... what is the diffirence bitween the japanese and the korean stick??? do the effect the gameplay or what?
Cynnik: "well ok, uh"
what do i do if i want to install 24 mm seimetsu buttons onto it
I wish I could find the buttons that had the bevel, the really old school
I bought the korean version of etokki and it stopped working for no reason just after a few week. What could be the problem? Please help
Nomentsoa You, my friend, are fucked
Just send it back bro
The PCB died and they sent me a new one for free, I just paid the shipping.
very nice m8 :) is it any good? u using circular gate? I ve a mad catz with square gate atm. But i send it back and will get a circular gate. Because my movement seems to be bad on a square. Is it a big diffrence?
I bought the korean version, it was my very fitst stick so I didn't want to test every gate, too expensive. I'm pretty happy with it so far.
how to updated the frimware it disconnected every 8 mints on ps4
فيصل الموسى The firmware update is here twitter.com/etokki/status/756517376959459328
custom shaft or Crown CWL 306 which has balltop as default
I just want that stick in my te....i already ordered one just need to kno how.
I don't understand the people who buys korean stick and mod it with japanese parts why don't you go and buy a japanes stick from the beginning
exactly what i said
+This name is boring 😂
because noobs like me thought that circular gates were better at first before we did the research and realized that square gates are better and we don't wanna buy another etokki
isnt the etokki omni stick better for tekken? im thinking about buying one. i mean with a circular gate.
I bought the etokki because of its design, sturdyness and ability to house whatever kind of hardware. i am free to try out both japanese and korean levers without having to buy a completely new case. Its pretty obvious, dumbo.
they uploaded a video on it
The Korean stick looks exactly like a typical American HAPP stick.
I know this is is an old comment but the difference is the Korean stick has no restrictor gate
yo brother just got my omni , when you move the lever is the dust cover supposed to be loose?
yes
now why buy a Korean arcade stick....and put Japanese buttons n stick on it?
Sanwa buttons are better than Korean buttons.
aha!! thanks!!
Just saw it after i commented :X