Would you mind giving a little info on changing startup tone? I have made a few in blheli. I kinda looked at source code to see if I could spot anything to replace. Thanks for the work you've done.
Did I already talk to you on facebook? Mostly you edit the sounds.c file then compile for your ESC. For now you need to be able to compile the firmware to change the sounds.
I'm having cogging between the slow start up and normal motor operation. Any way to fix that? Do you have an updated bin file?Does it on all motors 1000kv to 2000kv. Wraith 32 35amp, wraith 32 50 amp. Messed with all settings on the esc config. Software. Thanks for the videos! I could watch these videos for hours.
I don't know. But I have seen them talk about flycolor ESC's in the slack chat. For the most part all of the ESCs flash the same way. They just use different firmware files.
Are you willing to sell a few of those esc's with the new firmware installed? So i would have to just solder up batt and motor connectors and go? Let me know
So is 35a enough for 1/10 scale? I run a 1800kv HH Devolver and would love to make it quiet but have a smaller esc than the sw4 I’m running. I don’t know the amp draw on 1800kv compared to the 1400kv you are running. I would hate smoke it.
The ESC is a Airbot Wraith32 55a that cam with BLheli32. I loaded it with custom AM32 firmware . They are pretty much impossible to get now. The motor is a HobbyStar 2820 (3542) Brushless Outrunner Motor 1450KV. These have also jumped up in price since the video came out.
If I did they would sell out. Here is a list of known hardware github.com/AlkaMotors/AM32-MultiRotor-ESC-firmware/wiki/List-of-Supported-Hardware that works, Also try joining the Slack chat am32-invite.herokuapp.com/ you can ask there
![[#2024MAMA] ROSÉ (로제), Bruno Mars - APT. | Mnet 241122 방송](http://i.ytimg.com/vi/dgGqD28J6aQ/mqdefault.jpg)
I could watch your stuff all day, awesome job.
I appreciate the support, I wish I could make them all day too!
Theres also a ESC like that selling from indonesia ,3 Poly they sell it with 50a and 80a .Love the "Sammy" that pass by.
Good stuff. I think I might just try this out. Whole combo cheaper than a decent sensored motor!
You should!
Would you mind giving a little info on changing startup tone? I have made a few in blheli. I kinda looked at source code to see if I could spot anything to replace. Thanks for the work you've done.
Did I already talk to you on facebook?
Mostly you edit the sounds.c file then compile for your ESC.
For now you need to be able to compile the firmware to change the sounds.
I want to get one of the esc for my scx24 or 1/10 scale.
I'm having cogging between the slow start up and normal motor operation. Any way to fix that? Do you have an updated bin file?Does it on all motors 1000kv to 2000kv. Wraith 32 35amp, wraith 32 50 amp. Messed with all settings on the esc config. Software. Thanks for the videos! I could watch these videos for hours.
amazing🤩 I wanna try this
awsome dude ,nice job ,,what type or brand of the esc ?
this particular esc is a 24$ Airbot Wraith32 50A flashed with custom am32 firmware www.readytoflyquads.com/50a-wraith32-plus-32bit-blheli-esc
Red wire from ESC to Rx, could be left out using a Bec correct? I was about to solder up a board and realized I'll prob need a Bec!
Yes, you probably need a BEC, or a second small 5-9v battery
perfect, where can I buy this combo?
It's more of a DIY project and not something you can just buy.
Info and link to a How To is in the description.
I want to have one
I currently use flycolor blheli_32, do you know if I download am32 can I use the same usb for programming?
I don't know. But I have seen them talk about flycolor ESC's in the slack chat. For the most part all of the ESCs flash the same way. They just use different firmware files.
These are getting out of hand haha. My devolver/ sw4 isnt even that slow but yet again that capra trans is geared up
Impressive!
Are you willing to sell a few of those esc's with the new firmware installed? So i would have to just solder up batt and motor connectors and go? Let me know
No, I don't want the hassle or responsibility if anything doesn't work or the hassle of shipping. Plus you learn more doing it yourself!
🥰🤩💥💯👍👏
So is 35a enough for 1/10 scale? I run a 1800kv HH Devolver and would love to make it quiet but have a smaller esc than the sw4 I’m running. I don’t know the amp draw on 1800kv compared to the 1400kv you are running. I would hate smoke it.
Depends on lots of things, I have not had problems so far, but my driving is conservative.
@@HouseofVoodoo are you using the 55a model?
I must have missed it but what exact motor and esc are you running here?
The ESC is a Airbot Wraith32 55a that cam with BLheli32. I loaded it with custom AM32 firmware . They are pretty much impossible to get now.
The motor is a HobbyStar 2820 (3542) Brushless Outrunner Motor 1450KV. These have also jumped up in price since the video came out.
What servo are you running???
A JX Direct Power Servo, probably not a brushless one. Its ok, not as good as the holmeshobbies.com/electronics-and-wiring/servos/shv800-servo.html
Did you re-program the esc?
yes, using am32
Cant give me link esc?
If I did they would sell out. Here is a list of known hardware github.com/AlkaMotors/AM32-MultiRotor-ESC-firmware/wiki/List-of-Supported-Hardware that works, Also try joining the Slack chat am32-invite.herokuapp.com/ you can ask there
Can I buy one of these
I don't sell them but there is a link in the description on how you can make one.