Subbed. Just got into RC and boats are on the list! You have been my "boat guy" for learning about boats for a very long time and I appreciate all of your hard work and dedication to providing knowledge and information to us newcomers to the hobby! THANK YOU!
This is an immediate subscribe for anyone new or old ro RC boats. I'm new and this is invaluable info. Although I'm sure you've read that I've had a very interesting time on my first couple of runs with the boat acting erratic and taking off on its own and me having to catch it and slicing one of my fingers in the process. So this video about waterproofing is absolutely critical for me
Great Video sir!! Thank you for all this information. I'm dealing with this exact issue with the Zonda I just purchased. These boats come new with no latches, fasteners, seals or anything for the hatch. Been trying to figure out the best way to secure the hatch and keep her dry. Video couldn't have come at a better time. Again,, THANK YOU!!!!!!!!!!! HERO!!!
Another really helpful video Big B, thanks for sharing. That shrink tubing tip for the stuffing tube into the strut is priceless 👌 Where were you when they built the Titanic? Oh... wait... not even born yet! 😆
Thank you for this video! I had a big leak in my new to me Traxxas Blast. Checked the boat in my bath tub. It floated in tub for 1 hour no leak, but when I run the boat it would fill up fast 🤔. Figured it was cooling system leak, took syringe and pumped water through, no leak. Ran boat with no prop like in video no leak…Then I started checking hull penetrations. The water cooling exit was too big for cooling tubing, and was letting a TON of water in. The water covers the hole before getting up on plane, which is why it filled up only when driving. Put heat shrink on tubing to make tight fit. NO MORE LEAKS 🎉 thank you
Man...i cant stress how sketch zipties are on lines...especially fuel! They create a pinch point thatll suck air...think of a teardrop.... try cutting a 5mm section of your line and stretching it over before installing....works 1000x better than a ziptie and no cut points...and easier to do than safety wire... thanks for all the info you put out too....learnin a lot every time i watch new vids!
@@ClickLikeAndSubscribe been doin it for my fuel lines in gas airplanes for years! Just got into boats and applied same methods....we wanna keep fuel in the tank and water outta the hull!
Very very info man! You are the best on boat vids Ive found. Got a UL-19 2 months ago and 3 leaks/issues I found that were tricky to find. 1.Small leak in hull where stuffing tube goes through the hull. Only leaked under power. 2. Orings on hatch nuts, even taping off hatch they can leak. slightly larger orings on thumb screws and vacuum caps on the inside of the boat pretty eliminate that. 3. This was a 2 fold issue. They tightened down a nipple/barb on the cooling jacket to tight. It cracked the plastic washer and would leak under power, but also being turned in to far almost cut off water supply through motor. I used stainless washers and thread tape on that. This was just something I found on this specific boat that might apply to others.
@@IRONCLADRC You should be able to get them at any auto parts store. The assorted packs with different colors are silicon and longer. Less than 10 bucks.
First your additional water cooling pick up and now adding pool noodles, my BJ24 is becoming a tank. I have been researching parts for my boat and wondering your opinion on two things. First would you buy an original flex shaft or upgrade to the OSE? Second do you know any part number to replace the steering rod end? Proboat/Horizon do not offer a replacement. Keep the tips coming sir, awesome work.
I wonder where you guys get all that electronics or electric stuff and motors because im trying to make myself my own boat i was also watching this video because i had some rc boats before (bought them from store) and the water kept coming in and i couldnt stop it so this video will actually help me at my new project so thanks 🙏😂👍
Started on my DF45 MKII today, that stinger really brings motor far back, so i will need to move batteries in front, or run paralell ;) Not that i complain on running paralell 6s. Guessing around 42-45mm props on the Leo 2200kv, but lets see how it behaves on 45mm prop and 4s
Another way to check for leaks is to put your boat on a stand, poor water into the hull and see where it leaks out. Gravity will reveal most leaks. BoatGang
You may have to buy the whole strut? Check Offshoreelectrics.com he may have them or horizon hobby www.avantlink.com/click.php?tt=cl&merchant_id=953aec29-878e-4306-b620-2df85883455e&website_id=70256520-69d3-496b-a06d-cfbf9af7a81d&url=https%3A%2F%2Fwww.horizonhobby.com%2Fhttps%3A%2F%2Fwww.horizonhobby.com%2Fproduct%2Fpropeller-strut-sonicwake-36-v2%2FPRB282093.html
Hey big B how's it's going I just have a question for you I want to move my water outlet to the top of my boat so I can see it how can I drill the hole or something can drill on the VELES 29, If u could answer this for me upgrading water outlet size to M8 thanks
So question I have a black jack 24 and the boat got sea water in it, and last time I was trying to run it but it wouldn’t do nothing and all of a sudden it did but then I wouldn’t again, few months later the battery was swollen, now my question is any other electronic gonna be bad or can I just buy a new battery and it’s gonna run fine?
Depends did you rinse the boat off with fresh water after you tan it in salt water? If not then you'll just have to see once you plug in your new battery. Wish I could help more.
Otherwise, excellent content! Now, if we could get a "How to: carbon fiber inlay the cats.. V hulls easy. The sponsons of the catamarans, are a pain to get right. (Dont ask me how i found out)
Man mines got more leaks then a sponge haha... Only Thing I can think to do beside soapy water and air pressure was to fluoresce the water and put it in a dark room with a black light and watch to see where it comes in 🤔 I'm fairly certain it's my packing tube as I can hold it under water with maybe a sprinkle of water and sat it in the sink for an hour.. little got in but that's due to the dodgey foam seal...it's entirely porous 🧽 😂 trying to convince myself to go get a boat with a single piece hull and flat plate latch as I know I can get that to seal haha .
@@IRONCLADRC when I read that ...I immediately felt the pucker factor kick in 😂😂 👍 I'll give it ago I'll take out my servo n that first as it isn't remotely water resistant apparently.. thanks mate 😁
Also what do you think of either putting down a bead of vasoline between the lid and seal I know that stuff doesn't like water haha .. however I don't want to go killing the native invertebrates as I know for example that one drop flea stuff and wipeout a lake in a couple hours so I'm a bit sketchy with what I'm adding haah
Subbed. Just got into RC and boats are on the list! You have been my "boat guy" for learning about boats for a very long time and I appreciate all of your hard work and dedication to providing knowledge and information to us newcomers to the hobby! THANK YOU!
No problem brother glad I could help
Preschool building blocks is genius..! I normally use just packing foam but I like your idea. Also thanks for the tip on leaky motor jackets.
This is an immediate subscribe for anyone new or old ro RC boats. I'm new and this is invaluable info. Although I'm sure you've read that I've had a very interesting time on my first couple of runs with the boat acting erratic and taking off on its own and me having to catch it and slicing one of my fingers in the process. So this video about waterproofing is absolutely critical for me
Great Video sir!! Thank you for all this information. I'm dealing with this exact issue with the Zonda I just purchased. These boats come new with no latches, fasteners, seals or anything for the hatch. Been trying to figure out the best way to secure the hatch and keep her dry. Video couldn't have come at a better time. Again,, THANK YOU!!!!!!!!!!! HERO!!!
Yep I made this vid for you basically. Could t remember your user name lol.
Top video man! some really cool ideas there I didnt know. Love this sort of video!! So much info and experience! Cheers mate!👍🏻
Another really helpful video Big B, thanks for sharing. That shrink tubing tip for the stuffing tube into the strut is priceless 👌
Where were you when they built the Titanic? Oh... wait... not even born yet! 😆
Glad I could help
Thank you for this video! I had a big leak in my new to me Traxxas Blast. Checked the boat in my bath tub. It floated in tub for 1 hour no leak, but when I run the boat it would fill up fast 🤔. Figured it was cooling system leak, took syringe and pumped water through, no leak. Ran boat with no prop like in video no leak…Then I started checking hull penetrations. The water cooling exit was too big for cooling tubing, and was letting a TON of water in. The water covers the hole before getting up on plane, which is why it filled up only when driving. Put heat shrink on tubing to make tight fit. NO MORE LEAKS 🎉 thank you
Glad I can help.
I used some gray rtv to make the hatch on my stealthwake fit more snug and have a "rubberized" seal. Works real good! Wish I could send you pics.
Man...i cant stress how sketch zipties are on lines...especially fuel! They create a pinch point thatll suck air...think of a teardrop.... try cutting a 5mm section of your line and stretching it over before installing....works 1000x better than a ziptie and no cut points...and easier to do than safety wire... thanks for all the info you put out too....learnin a lot every time i watch new vids!
Good point, thanks for adding, I'll do that before zip ties!
@@ClickLikeAndSubscribe been doin it for my fuel lines in gas airplanes for years! Just got into boats and applied same methods....we wanna keep fuel in the tank and water outta the hull!
@@tommymatherne2673 gas powered RC planes is the whole next level to get into! Maybe after gas boats :)
Great advice BIG B.
Very very info man! You are the best on boat vids Ive found.
Got a UL-19 2 months ago and 3 leaks/issues I found that were tricky to find.
1.Small leak in hull where stuffing tube goes through the hull. Only leaked under power.
2. Orings on hatch nuts, even taping off hatch they can leak. slightly larger orings on thumb screws and vacuum caps on the inside of the boat pretty eliminate that.
3. This was a 2 fold issue. They tightened down a nipple/barb on the cooling jacket to tight. It cracked the plastic washer and would leak under power, but also being turned in to far almost cut off water supply through motor. I used stainless washers and thread tape on that.
This was just something I found on this specific boat that might apply to others.
Thanks for sharing. Do you have a link for the vacuum caps for the thumb nut? I've been looking with out lucka
@@IRONCLADRC You should be able to get them at any auto parts store. The assorted packs with different colors are silicon and longer. Less than 10 bucks.
Great Information vid. Thank's for Sharing Big B 👊👍✌💯
First your additional water cooling pick up and now adding pool noodles, my BJ24 is becoming a tank. I have been researching parts for my boat and wondering your opinion on two things. First would you buy an original flex shaft or upgrade to the OSE? Second do you know any part number to replace the steering rod end? Proboat/Horizon do not offer a replacement. Keep the tips coming sir, awesome work.
I'd get the ose upgraded Flex & strut. As for the steering rod end you can use an ez-connector instead
Big B your the man👍 top tips galore there buddy some I will sure be putting into practice
Glad I can help brother.
I wonder where you guys get all that electronics or electric stuff and motors because im trying to make myself my own boat i was also watching this video because i had some rc boats before (bought them from store) and the water kept coming in and i couldnt stop it so this video will actually help me at my new project so thanks 🙏😂👍
I use Off shore electrics for almost all my rc boating needs
www.offshoreelectrics.com/categories.php?cat=Motors&PARTNER=ironclad
Great video Big B👍
Great Tips.
Bad ass thanks for the information man
Another good informative video! Love it Big B ❤️
Don`t forget that a syringe can put pressure in the water lines like when you run the boat. Very easy to find leaking hoses and waterjackets that way.
This was hella helpful for me my boat didn't have a hatch but every thing else is great information...do u have any nitro boats ?
No sir unfortunately I don't have any nitro or gas boats. Glad I could help
Started on my DF45 MKII today, that stinger really brings motor far back, so i will need to move batteries in front, or run paralell ;) Not that i complain on running paralell 6s.
Guessing around 42-45mm props on the Leo 2200kv, but lets see how it behaves on 45mm prop and 4s
Awesome. Thanks for the update brother. Good luck with the run.
Another way to check for leaks is to put your boat on a stand, poor water into the hull and see where it leaks out. Gravity will reveal most leaks. BoatGang
We use to do that with aluminum Jon boats to find a leak. It works 💪
I think you mentioned in another video that the bushings in the V1 and V2 are different. Where do you get a V2 bushing, I can't seem to find them?
You may have to buy the whole strut? Check Offshoreelectrics.com he may have them or horizon hobby www.avantlink.com/click.php?tt=cl&merchant_id=953aec29-878e-4306-b620-2df85883455e&website_id=70256520-69d3-496b-a06d-cfbf9af7a81d&url=https%3A%2F%2Fwww.horizonhobby.com%2Fhttps%3A%2F%2Fwww.horizonhobby.com%2Fproduct%2Fpropeller-strut-sonicwake-36-v2%2FPRB282093.html
Hey big B how's it's going I just have a question for you I want to move my water outlet to the top of my boat so I can see it how can I drill the hole or something can drill on the VELES 29, If u could answer this for me upgrading water outlet size to M8 thanks
The proper drill bit should do the trick nice and slow
So question I have a black jack 24 and the boat got sea water in it, and last time I was trying to run it but it wouldn’t do nothing and all of a sudden it did but then I wouldn’t again, few months later the battery was swollen, now my question is any other electronic gonna be bad or can I just buy a new battery and it’s gonna run fine?
Depends did you rinse the boat off with fresh water after you tan it in salt water? If not then you'll just have to see once you plug in your new battery. Wish I could help more.
@@IRONCLADRC yes rinsed it when I got home
Would silicome sealant substitude marine sealant
Long-term no, guess it really depends where you using it
ฉันอยากได้เรือคุณมาเล่นบ้างจัง
The "K" is silent.
"Nurled"...
Otherwise, excellent content!
Now, if we could get a "How to: carbon fiber inlay the cats..
V hulls easy.
The sponsons of the catamarans, are a pain to get right. (Dont ask me how i found out)
i feel dryer alredy.
Knurled the k is silent nurled
What can I say I'm from the south. 😆
Man mines got more leaks then a sponge haha... Only Thing I can think to do beside soapy water and air pressure was to fluoresce the water and put it in a dark room with a black light and watch to see where it comes in 🤔 I'm fairly certain it's my packing tube as I can hold it under water with maybe a sprinkle of water and sat it in the sink for an hour.. little got in but that's due to the dodgey foam seal...it's entirely porous 🧽 😂 trying to convince myself to go get a boat with a single piece hull and flat plate latch as I know I can get that to seal haha .
Fill the boat with water and watch where the water leaks through the hull
@@IRONCLADRC when I read that ...I immediately felt the pucker factor kick in 😂😂 👍 I'll give it ago I'll take out my servo n that first as it isn't remotely water resistant apparently.. thanks mate 😁
Also what do you think of either putting down a bead of vasoline between the lid and seal I know that stuff doesn't like water haha .. however I don't want to go killing the native invertebrates as I know for example that one drop flea stuff and wipeout a lake in a couple hours so I'm a bit sketchy with what I'm adding haah