99-07 SILVERADO 5.3 OIL PAN & REAR MAIN SEAL REPLACEMENT
HTML-код
- Опубликовано: 6 сен 2024
- Thanks for watching lady’s and gents!!!!
Make sure to subscribe for future content!!!
Go check out Summit Racing as well!!
www.summitraci...
We’ve got tons of stuff to finish knocking out. But the 5 speed swap is moving right along!!!
MUCH LOVE!!!
Email-business only- woodmarcus7@gmail.com
That's the factory wax E frame coating your scraping off. All of the oil pan bolts are 18 ft pounds. The two long ones into the rear cover are 106 inch pounds, and the two into the trans are 37 ft pounds.
Hey why come you did not do the o-ring on the pick up tube, just saying am quite sure it will need it soon . And great job.Dallas Tx. I the house.
Very informative and funny! Thanks for taking the time to show what it all consists of! Will definitely be using your channel to fix my truck 😁
Good choice of oil and oil filter lol. That’s exactly what I’ve been running in my truck for years. 137k when I bought it to 214k now. Runs like a goddamn beast with 0 lights on the dash. Butt.. unfortunately, it’s time for rear main/oil pan gasket obviously 🤣
Thanks for the Video. I have a 2001 GMC Sierra that needs Rear Main Seal and will most likely do Oil Pan at the same time. Thanks! 👍
I like the way he explained everything on detail 😎
I love your channel man but did you know your eyes have a red reflection in the camera the camera 😆 they glow red 👹😆
I changed rear main seal. Oil pan gasket and valve cover gaskets. Along with the oil pressure sensor. And I still have an oil leak. Where else could it be leaking from?
Crank sensor O ring next to the oil pressure sensor
Great commentary to go along with a very informative video
Have to replace my Rear Main on my Silverado. Might as well do the oil pan too just like you did .
why did u use a new oil pan?
You don’t have to unless your oil pan isn’t good but he said he just likes doing just because he is changing the gasket so mine as well just the oil pan but i didn’t change mine when i did it
You should also replace your oil pump pickup tube o ring
Do you have a part number on the Oil Filter?
looking to do this swap with my 02 suburban, how does the nv3500 compare to the 4l60e length wise? anyone know if i can use my np246 or would i be better off swapping to a lever operated transfer case?
Did you support the engine some how or was it hanging by the mounts, I need to do this to my 01 but unfortunately il be on the ground and it is 4x4 sliding back the tranny and transfer case as far as possible.
Remove the transfer case first
Awesome video wish it was a 4wheel drive 💪🏾💪🏾💪🏾💯
Someone told me you need a tool to line therear main up is that true
How long would just the rear main take ? Approximately
Wix or wix xp is what I use for oil filter
I have a 2006 Chevy Silverado 1500 4.3 I need to replace rear main seal and oil pan gasket is it on passenger or driver side or in the rear
What about wiring?? I bought a swap but they left automatic wiring in. What did you do?
I need your help I live in Kentucky also in the London area and I need to have my rear main seal replaced and don't know where to start now I know this video a year ago how much would you charge I have a 03 Silverado 1500 4.8 4-wheel drive
I have a question for you does it matter if it's a 4 wheel drive is the fitment the same or not on the oil pan
im seeing several of these videos but have a question. Why are you replacing the rear mail seal housing with dorman's whats the advantage? It seams like everyone is replacing it but why? I'm not seeing any bullletins from GM saying I should change It with a updated one.
Long story short, it's easier and cost about the same.
Longer explanation: To do a rear main correctly on an LS you need a special centering tool. It ensures the seal sits perfect on the crank. Some parts changers will just swap the entire housing thinking they will get around centering the seal. If you torque the main housing to the block before you insert the long oil pan bolts, you can usually get away with it. The problem occurs when you put the long bolts in before you set the seal housing, it will pull the housing down and initially cause a leak point at the bottom of the seal then cause excess wear on the top of the seal. Once the wear happens on the top you will have catastrophic failure. Most major parts stores have the loaner tool that centers the seal.
@@skab768 Ya, i bought the new dorman cover but then removed the seal, installed the cover properly with the alignment tool and bought another new seal and then installed the new seal. Doing it the right way is the only way to gaurantee your not taking it apart 2xs.
Where are you located? Have 2003 Tahoe would like for you to work on
I’m no mechanic but mine needs done bad.
Me encanta su video amigo saludos desde komchen hopelchen campeche
Great info. Enjoyed the video.
How much is for the oil pan
I decided to take a whack at just replacing the oil pan gasket. If I’m successful with the pan but the rear main seal is the main leak is my effort all in vain or can a rear main be done without dropping the oil pan?
You can replace the rear main without pulling the oil pan again. I just did the same thing lmao
Thanks, Yeah- turns out my oil
leak only got worse after new pan gasket and perhaps confirmed my suspicion that it’s the rear main.
Going rate Hawaii is 1600.00 for
that one 🧟♂️ I pictured myself doing it maybe snapping a few exhaust manifold bolts in the process. 😱
I have an 02 with the 6.0 and 4l80e and I believe I have a rear main seal leak and I just been topping it off for years because of how much the 4l80e weighs. I wonder if its worth a shot to see if its actually the oil pan gasket
Try oil pressure and cam sensor first
@@ericvetick4932 turned out to the be the rear cover. I figured this out after having to pull the engine because we had a catastrophic failure that resulted in 5 spun bearings. New gaskets everywhere now hopefully it wont have any leaks now
How.can i replace rear main seal of my chevy 1500 4x4 if i dont have car lift
I have the same question, so just talking with the wife...she says she's gonna build me a shop😶...aamco is gonna get my business because I am worth it 👌🏽...then be the consumer sassy if it STILL LEAKS!!!! The truck is worth the price of repair, absolutely no rust, good luck with yours brudda🇺🇸
On ur back
Good video
perfect timing my 5.3 oil pan is leaking
That is undercoating.
You need to watch your language
FUCKing a😂