How to Replace Rear Main Seal Cover 2007-2013 Chevy Silverado
HTML-код
- Опубликовано: 7 сен 2024
- Buy Now!
New Rear Main Seal Cover from 1AAuto.com 1aau.to/ib/1AEM...
This video shows you how to install a rear main seal cover on your 2007-2013 Chevy Silverado.
This process should be similar on the following vehicles:
2007 Chevrolet Silverado 1500
2008 Chevrolet Silverado 1500
2009 Chevrolet Silverado 1500
2010 Chevrolet Silverado 1500
2011 Chevrolet Silverado 1500
2012 Chevrolet Silverado 1500
2013 Chevrolet Silverado 1500
Tools you will need:
• Flat Blade Screwdriver 1aau.to/obb2/1A...
• Pry Bar 1aau.to/oNs/1AX...
• 10mm Wrench 1aau.to/oRd/1AX...
• 11mm Wrench 1aau.to/oRd/1AX...
• 13mm Wrench 1aau.to/oRd/1AX...
• 15mm Wrench 1aau.to/oRd/1AX...
• 21mm wrench
• 10mm Socket 1aau.to/oaXL/1A...
• 11mm Socket 1aau.to/obgw/1A...
• 13mm Socket 1aau.to/obgw/1A...
• 14mm Socket 1aau.to/obgw/1A...
• 15mm Socket 1aau.to/obgw/1A...
• 21mm Socket 1aau.to/o9x/1AX...
• 24mm Socket
• 8mm Socket 1aau.to/oaXL/1A...
• Engine Hoist
• O2 Sensor Socket
• Trim Tool Set 1aau.to/o4d/1AX...
• Needle nose pliers 1aau.to/oAw/1AX...
• Needle nose pliers 1aau.to/oAw/1AX...
• Pliers
• Ratchet 1aau.to/obrn/1A...
• Socket Extensions 1aau.to/obgw/1A...
• Swivel
• Torque Wrench 1aau.to/oavb/1A...
• Brake Parts Cleaner
• Liquid Thread Locker
• Marker / Writing Utensil
• RTV
• Silicone Paste
• Drain Pan 1aau.to/owd/1AX...
• Hammer 1aau.to/oQe/1AX...
• Pick 1aau.to/oJC/1AX...
• Pole Jack
• Razor Blade / Gasket Scraper 1aau.to/oie/1AX...
Subscribe: / @trq
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
√ Watch the Video
√ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts
√ Do it Yourself
√ Save Money
1:06 Torque the rear face cover bolts 1st to keep good alignment. Then torque the bottom. Other than that, great video!
Not sure this is one i can tackle in my driveway LOL. Great video though.
You’re supposed to use the alignment tool and torque the plate bolts before the long pan bolts. If you don’t it pulls the seal down and out of alignment.
Not sure if my rear main or my cover is leaking on my 2013 Express 5.3 with 250,*** miles. But I am absolutely going to do both since I am in there. Thanks for the visual!
+Dave P Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts! 1aau.to/m/Shop-TRQ
Tighten bottom bolts first,,,,I'm sure thats right 🤞🏻
Curious did you have to drain the oil? To do the seal? I’m at this part for my trucj
How much a job like cost to get done I need this done on my Tahoe 08 4.8l
how many hours is this job
What would a job like this cost at a repair shop?
Around $1000.00 on my 2018 Suburban
What is the cost of that repair?
Bottoms bolts 106 lb ? Are you serious
I could’ve gotten those exhaust bolts in quicker with a wrench
Do not take the white inner seal piece off until your installing. Let the crank push it off... Once it's removed the seal starts to collapse inward. 🤦♂
To replace the rear main seal, wouldn't it be easier to pull out the engine then transmission?