Are you some kind of wizard? I was looking up how to upgrade my ender 3v2 firmware to jyers and there you are. I started looking for a larger printer and here you are again. You rock !
Straight forward and thorough review. I would've liked to see Evnovo/Artillery do three things with the X2: 1. Add gantry stiffeners to allow for higher accelerations all around. 2. Incorporate a linear advance option that you can tune via a built-in file. 3. Partnered with Fulament to add a removable print surface as a factory option, rather than the glass.
Thank you for the review. I'm looking to get my first 3D printer and after watching a lot of reviews on many different printers, I'm really leaning towards this one.
Well, I have an unboxing in an upcoming video, but the unboxing part is a time lapse with a voice over, in which I'm talking about the printer's specs. Plus you can skip it using the chapter markers on the timeline. 😉
Thanx for the revue Bryan, this is definitely on my wishlist for next year, especially because of its lack of fan noise. My CR-10S Pro is deafeningly loud, as its on a table in my small office.
Getting ready to buy my first printer and printing TPU is a must. I know the Sovol does a good job and I saw your review on the Creality Ender-3 S1 where you said it handled TPU without issue. How about this printer, you never mentioned other filament types...
A little late but I'll respond for others having the same question. I've had my x2 for 4 months now and I use it primarily for petg and tpu. Does an excellent job with both once you've tuned it to that specific roll. I use cura slicer and always start with the generic setting then adjust after a small test print. My only complaint is the nonremovable build plate. It needs to be thoroughly cleaned every few prints and it's just more annoying not being able to take it off for a good scrub.
Just got my ender 3 v2 with jyers installed thanks to your help, but dang this is a nice printer! Not quite jumping on buying a second one so soon, but I like the list of features this offers for the price. Great review, thanks as always!
I throughly enjoy watching your reviews. It was on your good advise I recently ordered my longer LK5. It was on back order but for the money a great first printing. It arrived this afternoon but before opening it watched this review and think I might be sending it back! lol. keep up the good work my friend!
@@mactastic144 oh I'm sure there is, however if removing the original surface is such a pain then installing this would be problematic to begin with. That's not to say I'd not be put off from replacing the glass bed with the removable one. I do this as a matter of course on the printers I own. I ad a veery bad experience a few years ago with a glass bed shattering on me and I, personally, don't trust glass any more.
I have an X1- and seriously considering an X2. I have had to rewire the head direct to the mainboard, because of unreliability of the connectors, and it sticks out on my bench because of the bed cable, and the reel holder is a pain.
Well I might as well not bother with my review video as you've covered it all. But I guess @artillery3d will want my input. Perfect review my friend 👍👍👍
Bryan, this was a very, very good review! I'm very happy you tied up your mop because it makes you look very professional. I'm sorry that certain looks make me shy away from RUclips channels but they do. I almost un-subscribed because I couldn't take you seriously. I like learning from your channel because I'm old (69) and don't have the experience you or the other RUclips channels. Thank you.
Thanks for reviewing this printer, I got my X1 last year and have been very happy with it. For it's large size, it's a more reliable printer than my Ender 3 v2.
@@wskwong2000 It took me a while to get it dialed in and working right. The Sidewinder was much easier getting up and running. Now that I have the Ender working like it should, it's been a good little printer.
Hello thanks for this review! I’m about to buy it the X2 !! but a lot of people in the Facebook group make me hesitate with the sovol s03 or the b12/300, Would you have some advice what do you think about those three , people said sovol Is more precise, … so all my compare studies is down lol , now I don’t know anymore which one is the best for me so if you can help thank you
What do the S and Z commands signify when using M420? I thought they would have started using a heated aluminium plate instead of sticking the heater to the glass build plate, many people I know in the community have moddded their X1 with a plate so they can use alternative build surfaces, of course they could always place the new build surface on to the glass plate but from what I gather they prefer the standard aproach
Hi Andrew! The S parameter enables or disables the use of the stored mesh. It's a Boolean value. So, 1 enables, 0 disables. The Z parameter is the fade height. The Marlin documentation says it means "Set Z fade height," but doesn't specify units. I assumed the units were layers, but it might be millimeters. As for the bed, maybe a Sidewinder X2 Pro would have an aluminum bed with a magnetic spring steel sheet? Up until Fulament sent the Fulabed upgrade to me, I was happy enough with the X1's bed. The heater-on-glass combination heats up really fast. I may pick up a Wham Bam system for the X2 in a few months and see how that performs. I realize the magnet and spring steel sheet are going to add thermal mass (and regular "Mass" mass) to the bed, so it'll heat slower and be heavier. That'll increase the heating time. But I love me a good spring steel sheet!
This looks like a nice printer. If I didn't already have 4 other printers and I hadn't sworn off bed slingers forever I might have considered buying it. In any case, I may be able to recommend it as a good first printer for someone just starting out.
@@Gi_Gantor These days I'm using the Ender 5 Plus and Voron printers. They're not beginner models but they are rock solid and produce excellent results.
@@BV3D Honestly, after watching your review of the sidewinder x2, I think I might go with artillery. The fixed bed was an issue for me, but I can get a removable bed and be fine. the rest of you "do not likes" don't sound to bad either. Thanks!
What would you say is the best 3D printer below 500 dollars? I really like this one, after seeing a few reviews, but there are some many options that make me confused. Please, let me know. I’m a beginner and want a printer to learn and print stuff to sell occasionally. Thanks!
Hi Bryan, Is there any difference between the X2 & the Genius? It looks like the X2 is now exactly the same as the Genius besides the format. Btw: the Genius has no problems with the USB stick. What is very easy to break is the BL sensor. Mine broke when i printed several parts at once. One parts came loose from the bed and the BL sensor hit that and broke. So be aware of that!
Thank you for the informative detail on this printer. I am really looking towards this printer and I have a couple of questions. 1st is the sizes: I'm looking to use this for printer 3d game boards like walls and floor tiles. Have u done so or will this printer be good for that. I also of course will do larger prints, but looking to see if I could both? 2nd I have seen other videos recommending to place supports on this do to the wobbling at full height, (however you printed that rocket and it looks great). Did you have wobbling issues or seen that? Thank you for your time.
Great review. Got few questions. What sort of print surface it come with? Can we print PETG ? I see it’s got two z-axis motors. How does it know the gantry is levelled? Does it have that auto check feature that Prusa got?
anyone else having an issue with the leveling of the machine? mine seems to want to nose dive though the bed. But once i bump up the Z by 0.05mm it rocks!
Hi Bryangreat video, i like the way you talk through the code to add into the start GRBL, i like A B C steps for things im new too. Hopefully youll answer this but could i ask, i downloaded the XYZ cube from thingy verse and opened it up in Cura I then saved to the USB stick that came with my Sidewinder 2, how does the added in start code get to my printer, when i saved the cube to the stick did it put that code in ? hope you understand what im meaning. thx. Ive subcribed to you.
great video, thank you I have added the line in my printing, do you perhaps have the link for the spool adapter please, I have hunted for Bjorn the hunter with no joy, thanks again and have a merry Xmas
My print has regular horizon bumps across. Does anyone know how to fix that? Also ironing the top layer turns out real bad. What should the setting be?
Gracias por tus video, me parece muy interesante, hace pocos dias que tengo la impresora Artillery Sinderwinder X2 pero tengo un problema, que cuando hago las pruebas de las dos funciones que son (PERDIDA DE ENERGIA Y EL SENSOR DE FINAL DE FILAMENTO) le doy ala tecla de reanudar si que retorna al lugar donde lo dejo para seguir, pero no detecta el filamento sigue la función pero sin imprimir, (que puede ser), si alguien tiene la solución al problema se lo AGRADECERE de todo corazón
I would like to know as well. Going to buy my first printer soon.
2 года назад
@@RyKnocks I decided to go with the Ender 3 S1 as my first printer. Was thinking about the SX2 for long time but what changed my mind is the amount of people using Ender devices - the community is bigger for sure and in my country there is official Creality reseller which makes it very easy to get spare parts etc. The bigger print volume is a nice thing for SX2 but at the same time you can build almost anything with smaller one but you need to split it into smaller parts.
My X2 had a failure of the automatic bed leveling. The Z axis would crash to the bed. Artillery sent a replacement unit that didn't work either. That was the end of their involvement so I have a printer that doesn't work. Total waste of time and money.
I really like your channel. I entered this world with a I need 3 v2 and you with your videos helps me alot. I put my marlin fiemware in it with your help :) Can you do the same it this one I’m getting one next week and m600 is amazing feature I like to add to This x2 printer . Thanks continue the good work 😅😀
Sadly , I've had nothing but issue's with mine . I've had it for 12 days and not one single print . I have a video on my channel to look at if interested . Bed doesn't heat up either .
I'm actually quite conflicted here. Your video shows fantastic print results with this printer. I'm curious why then this reviewer produced utter garbage on the very same printer - ruclips.net/video/9JZqosMxmxk/видео.html. Did you have to tweak it off camera for an extended period or is this other reviewer just clueless? I personally think this printer is beyond ugly, but I really don't care if it prints well and is at least somewhat faster than my Ender 3. My first (and probably only) upgrade would be to remove the build plate and add something magnetic as I have not heard good things about the one it includes.
Are you some kind of wizard? I was looking up how to upgrade my ender 3v2 firmware to jyers and there you are. I started looking for a larger printer and here you are again. You rock !
Straight forward and thorough review. I would've liked to see Evnovo/Artillery do three things with the X2:
1. Add gantry stiffeners to allow for higher accelerations all around.
2. Incorporate a linear advance option that you can tune via a built-in file.
3. Partnered with Fulament to add a removable print surface as a factory option, rather than the glass.
They’re not a software company. Digant maintains better firmware on Thingiverse.
Bryan, thank you for the review, we'll address our engineers on the problem on power loss recovery feature.
At first I thought you had gotten your hairs cut and I audibly gasped
Haha! That's why I had the note at the beginning! 😅
Thank you for the review. I'm looking to get my first 3D printer and after watching a lot of reviews on many different printers, I'm really leaning towards this one.
did you get it?
Great video. Thanks for not boring us with an unboxing!
Well, I have an unboxing in an upcoming video, but the unboxing part is a time lapse with a voice over, in which I'm talking about the printer's specs. Plus you can skip it using the chapter markers on the timeline. 😉
Thanx for the revue Bryan, this is definitely on my wishlist for next year, especially because of its lack of fan noise. My CR-10S Pro is deafeningly loud, as its on a table in my small office.
Getting ready to buy my first printer and printing TPU is a must. I know the Sovol does a good job and I saw your review on the Creality Ender-3 S1 where you said it handled TPU without issue. How about this printer, you never mentioned other filament types...
A little late but I'll respond for others having the same question. I've had my x2 for 4 months now and I use it primarily for petg and tpu. Does an excellent job with both once you've tuned it to that specific roll. I use cura slicer and always start with the generic setting then adjust after a small test print. My only complaint is the nonremovable build plate. It needs to be thoroughly cleaned every few prints and it's just more annoying not being able to take it off for a good scrub.
Great video, thanks!
Glad you liked it!
Hope you can get the Ender-3 S1 soon.
Just got my ender 3 v2 with jyers installed thanks to your help, but dang this is a nice printer! Not quite jumping on buying a second one so soon, but I like the list of features this offers for the price. Great review, thanks as always!
I throughly enjoy watching your reviews. It was on your good advise I recently ordered my longer LK5. It was on back order but for the money a great first printing. It arrived this afternoon but before opening it watched this review and think I might be sending it back! lol. keep up the good work my friend!
One problem with the X1 that hasn't been fixed in the X2 is the non-removable print surface. If you damage the bed it's a total pig to replace.
That’s a really dumb thing to have not fixed ! Def got to be a massive downside
There a third party magnetic build surfaces you can install.
@@mactastic144 oh I'm sure there is, however if removing the original surface is such a pain then installing this would be problematic to begin with. That's not to say I'd not be put off from replacing the glass bed with the removable one. I do this as a matter of course on the printers I own. I ad a veery bad experience a few years ago with a glass bed shattering on me and I, personally, don't trust glass any more.
Very nice review will keep this printer in mind for future purchase.
Bryan, you have the best 3D printing channel on YT! So much useful info in every video of yours!
I have an X1- and seriously considering an X2. I have had to rewire the head direct to the mainboard, because of unreliability of the connectors, and it sticks out on my bench because of the bed cable, and the reel holder is a pain.
It looks an interesting printer and nice to see they’ve corrected some of the issues with the 1. Thanks for looking over this printer for us
This video Really helped me with getting started with my X2 ! Thanks ! Subbed
Woah, awesome shirt!
Well I might as well not bother with my review video as you've covered it all. But I guess @artillery3d will want my input. Perfect review my friend 👍👍👍
Bryan, this was a very, very good review! I'm very happy you tied up your mop because it makes you look very professional. I'm sorry that certain looks make me shy away from RUclips channels but they do. I almost un-subscribed because I couldn't take you seriously. I like learning from your channel because I'm old (69) and don't have the experience you or the other RUclips channels. Thank you.
Thanks for reviewing this printer, I got my X1 last year and have been very happy with it. For it's large size, it's a more reliable printer than my Ender 3 v2.
What issue do you have with the ender v2? I actually am thinking of getting that one.
@@wskwong2000 It took me a while to get it dialed in and working right. The Sidewinder was much easier getting up and running. Now that I have the Ender working like it should, it's been a good little printer.
Great stuff!
Thank you!
That rocket only took 5 hours!? What speed were you printing at?
Hello thanks for this review! I’m about to buy it the X2 !! but a lot of people in the Facebook group make me hesitate with the sovol s03 or the b12/300, Would you have some advice what do you think about those three , people said sovol Is more precise, … so all my compare studies is down lol , now I don’t know anymore which one is the best for me so if you can help thank you
What do the S and Z commands signify when using M420?
I thought they would have started using a heated aluminium plate instead of sticking the heater to the glass build plate, many people I know in the community have moddded their X1 with a plate so they can use alternative build surfaces, of course they could always place the new build surface on to the glass plate but from what I gather they prefer the standard aproach
Hi Andrew! The S parameter enables or disables the use of the stored mesh. It's a Boolean value. So, 1 enables, 0 disables. The Z parameter is the fade height. The Marlin documentation says it means "Set Z fade height," but doesn't specify units. I assumed the units were layers, but it might be millimeters.
As for the bed, maybe a Sidewinder X2 Pro would have an aluminum bed with a magnetic spring steel sheet? Up until Fulament sent the Fulabed upgrade to me, I was happy enough with the X1's bed. The heater-on-glass combination heats up really fast. I may pick up a Wham Bam system for the X2 in a few months and see how that performs. I realize the magnet and spring steel sheet are going to add thermal mass (and regular "Mass" mass) to the bed, so it'll heat slower and be heavier. That'll increase the heating time. But I love me a good spring steel sheet!
This looks like a nice printer. If I didn't already have 4 other printers and I hadn't sworn off bed slingers forever I might have considered buying it. In any case, I may be able to recommend it as a good first printer for someone just starting out.
What non-slinger printers do you use and recommend?
@@Gi_Gantor These days I'm using the Ender 5 Plus and Voron printers. They're not beginner models but they are rock solid and produce excellent results.
have a nice christmas and happy New year bv3d
I'm trying to decide between this and the sovol sv03. I'm leaning in sovols direction.
I've enjoyed my Sovol SV01, it's a good printer. I haven't used the SV03, but it looks pretty cool.
@@BV3D Honestly, after watching your review of the sidewinder x2, I think I might go with artillery. The fixed bed was an issue for me, but I can get a removable bed and be fine. the rest of you "do not likes" don't sound to bad either. Thanks!
Do you still have to add the M420? On later machines I see a 'save to eeprom"on the touch screen.
Is this a good printer for beginners, And Tinkercad? Or is it to advanced! Thank you!
Im looking at this and the ender 3 v2 what is better? I like the printable size the artillery has.
Great review as always. Thank you for your awesome work. 😊
What would you say is the best 3D printer below 500 dollars? I really like this one, after seeing a few reviews, but there are some many options that make me confused. Please, let me know. I’m a beginner and want a printer to learn and print stuff to sell occasionally. Thanks!
WHO IS THAT GUY..?? Just kiddin...great and informatve vid ...as usual👍
Looking slick!
Thanks!
Hi Bryan, Is there any difference between the X2 & the Genius? It looks like the X2 is now exactly the same as the Genius besides the format. Btw: the Genius has no problems with the USB stick. What is very easy to break is the BL sensor. Mine broke when i printed several parts at once. One parts came loose from the bed and the BL sensor hit that and broke. So be aware of that!
Does anyone know the quality of the STL has to be to get the best print?
Really enjoyed this one, looking for a second printer and this helps. Regarding the apparel, what does the benchy read?
Hi! The Benchy silhouette is composed of a bunch of G-code. I have no idea if it's actual Benchy G-code or just something random, though. 😀
@@BV3D well...now I gotta know!!! Keep up the awesome work, you are an inspiration. Continue to be blessed by being a blessing to someone today!
I'm torn between this and the Ender-3 S1, decisions decisions...🤔🤔
Fantastic review, thank you.
Bryan if you had to choose between the Ender 3-S1 or the artillery x2 which would it be? Just curious I recently purchased a Ender 3 V2.
Thank you for the informative detail on this printer. I am really looking towards this printer and I have a couple of questions.
1st is the sizes: I'm looking to use this for printer 3d game boards like walls and floor tiles. Have u done so or will this printer be good for that. I also of course will do larger prints, but looking to see if I could both?
2nd I have seen other videos recommending to place supports on this do to the wobbling at full height, (however you printed that rocket and it looks great). Did you have wobbling issues or seen that?
Thank you for your time.
great video Bryan looks like a good improvement on the X1
Hello, thanks for sharing this review, I like Artillery quality! )
Great review. Got few questions. What sort of print surface it come with? Can we print PETG ? I see it’s got two z-axis motors. How does it know the gantry is levelled? Does it have that auto check feature that Prusa got?
anyone else having an issue with the leveling of the machine? mine seems to want to nose dive though the bed. But once i bump up the Z by 0.05mm it rocks!
That bed is a deal breaker for me. The glass surface doesnt last long and replacing it is a real pain.
Can you add a different bed plate over the top?
You can replace it with an aluminium bed (more uniform heat distribution) for
Does the single gantry cause any printing imperfections like an Ender 3 sometimes does?
Hi Bryangreat video, i like the way you talk through the code to add into the start GRBL, i like A B C steps for things im new too. Hopefully youll answer this but could i ask, i downloaded the XYZ cube from thingy verse and opened it up in Cura I then saved to the USB stick that came with my Sidewinder 2, how does the added in start code get to my printer, when i saved the cube to the stick did it put that code in ? hope you understand what im meaning. thx. Ive subcribed to you.
great video, thank you I have added the line in my printing, do you perhaps have the link for the spool adapter please, I have hunted for Bjorn the hunter with no joy, thanks again and have a merry Xmas
Good video
My print has regular horizon bumps across. Does anyone know how to fix that? Also ironing the top layer turns out real bad. What should the setting be?
Great review, I agree vase not vayse.
my z axis wobbles and although i am getting really good prints I would still like to get rid of that wobble. Any tips. thanks!
Gracias por tus video, me parece muy interesante, hace pocos dias que tengo la impresora Artillery Sinderwinder X2 pero tengo un problema, que cuando hago las pruebas de las dos funciones que son (PERDIDA DE ENERGIA Y EL SENSOR DE FINAL DE FILAMENTO) le doy ala tecla de reanudar si que retorna al lugar donde lo dejo para seguir, pero no detecta el filamento sigue la función pero sin imprimir, (que puede ser), si alguien tiene la solución al problema se lo AGRADECERE de todo corazón
X2 or cr 10s pro v2?
great!
Great review. Taking money and print size aside, which one would you recommend more? Sidewinder X2, Ender 3 S1 or Ender CR10 Smart Pro?
I would like to know as well. Going to buy my first printer soon.
@@RyKnocks I decided to go with the Ender 3 S1 as my first printer. Was thinking about the SX2 for long time but what changed my mind is the amount of people using Ender devices - the community is bigger for sure and in my country there is official Creality reseller which makes it very easy to get spare parts etc. The bigger print volume is a nice thing for SX2 but at the same time you can build almost anything with smaller one but you need to split it into smaller parts.
@ I don't like the Bowden extruder on the S1.
@@atonicoh Ender 3 S1 has direct drive extruder
My X2 had a failure of the automatic bed leveling. The Z axis would crash to the bed. Artillery sent a replacement unit that didn't work either. That was the end of their involvement so I have a printer that doesn't work. Total waste of time and money.
future man here, you can pick one up on geekbuying for about 250$
I really like your channel. I entered this world with a I need 3 v2 and you with your videos helps me alot. I put my marlin fiemware in it with your help :)
Can you do the same it this one I’m getting one next week and m600 is amazing feature I like to add to This x2 printer .
Thanks continue the good work 😅😀
what size nozzle were you using?
Hi! I used the stock 0.4mm nozzle.
Sadly , I've had nothing but issue's with mine . I've had it for 12 days and not one single print .
I have a video on my channel to look at if interested . Bed doesn't heat up either .
Use different firmware. Upgrade the TFT firmware with microSD card. As for mainboard firmware, it’s being worked on.
@@mactastic144 Didn't work , still grinding , also heat bed hasn't worked (says error) .
Thank you for your assistance
Whoever wants to save 20 minutes:
The new stuff is basically an auto bed leveling system and easier cable setup
I'm actually quite conflicted here. Your video shows fantastic print results with this printer. I'm curious why then this reviewer produced utter garbage on the very same printer - ruclips.net/video/9JZqosMxmxk/видео.html. Did you have to tweak it off camera for an extended period or is this other reviewer just clueless? I personally think this printer is beyond ugly, but I really don't care if it prints well and is at least somewhat faster than my Ender 3. My first (and probably only) upgrade would be to remove the build plate and add something magnetic as I have not heard good things about the one it includes.
Very bad printer