I cleaned the sensor next to the kitchen sink. I used mass airflow cleaner and left the component on the drainer. My daughter,later, came into the kitchen, saw the component and thought it was a dirty part of a food mixer. She put the sensor into the automatic dish washer. The next morning I found it, double cleaned, I wasn't very happy, but put it back into the car. It worked well. Never leave anything around with other people in the house.
Thanks for the good instruction video. After 222198 km my Prius1 start for 20 seconds and than shut down. I cleaned the mass air flow sensor and the throttle body housing in it runs like a new one. Thanks a lot !
U should not touch that thin wire. Just clean it with spray and let dry that its own. Keep 30 min do not put into ur car. After 30 min u can again install that.
Good video, very educating. Problem of taking the sensor off the connector, strength of fingers do not work. Use a rubber hammer and small straight screwdriver to chip it off, very softly. Once it was off, replacing by a new unit would be very easy.
You keep pointing to the wire with the bulb on the top of it. That wire is not the MAF sensor it's the IAT. ALSO spraying carb cleaner on a MAF will melt the plastic cover on the wires and resistors - TERRIBLE VIDEO
Advice: some people say if you disconnect the MAF sensor and the car dies, that means the sensor is good. This is not true. I spent few hundred bucks until a good mechanic told me it is untrue. It turned out I needed a mag sensor which I bought on eBay for less than $15.
I have a 2000 Toyota Camry. I just got it. It drove beautiful when I 1st got it 6 days ago. The motor was so quiet you couldn't even hear it running. Now, 3 days ago it started shaking real bad, staling, making a pinging noise, and the breaks are stiff. It's had to push them down. The oil and tran fluid look great and are full. I'm going to clean the sensor today and change spark plugs. It's not over hearing either. What do you think could be the problem? Also, put a new battery last night. Thank you in advance😊
Screws on Toyota cars that are made by Toyota do not use Phillips screws , they use JIS standed screws and need JIS screwdrivers to undo and tighten them or you risk damaging the screw head , if you do not have a JIS screwdriver use the the one provided in the toolkit in the boot of the car .
This guy is right use mass air flow sensor cleaner only if you can get it. If you can get that you won't need to brush at all. If you can't get it carburetor cleaner will work but you want to let that sensor dry for at least 30 to 45 minutes before reinstalling it. Carburetor cleaner will leave a small residue on your sensor but it still should fix your problem. Spend a $10 on a can of mass air flow cleaner period and don't brush it
Hello Peter, I might try that, what could be the issue if my camry 2001, 4 cylinder lags in acceralation, the RPM needle goes to number 3 rev when it goes into the next speed, and the sound it makes is like a stuck sound like if it has air stuck, like a mini-boom sound and the sound comes from under the fuses around the right corner of the air filter, what's your take? I'm thinking probably the throttle fuse? Anyways, thanks!
Peter Finn it has 195,351 miles on it, because it loses horsepower I thought it was the catalytic converter, so I got that change, then I have the camshaft position sensor change, then the air filter and spark plugs but none of that worked, can you give any tips?
Zemorah Ledesma pull the vacuum hose coming out from your fuel pressure regulator if gas comes out means thats bad, it's beginning to shut all the way when your driving
I just did this and cleaned the throttle body on my wife's 4runner and as I removed the top of the intake housing or whatever you call it to disconnect the whole top from the throttle body I noticed a small black hose on the back side.The problem is it is not connected and has at some point broke from where it connected. Can anyone help me with what this is and how important it is also,I don't know if it were like that previously or happened when I started moving stuff but I dint want it to cause any issues at all. Thanks
U cannot touch that u can damage the sensor good for that is mass CRC mass air flow sensor just spray a decent amount on the inside and outside and wait until gets dry.
look at the ingredients for MAF sensor cleaner and it is nearly the same as Carb cleaner. In fact, there is also hexane + Petrol in CRC MAF cleaner which is meant to be aggressive. You can use, de natured alcohol, electrical contact cleaner, carb cleaner (some are aggressive apparently) or isopropyl alcohol.
You do not use carb cleaner on that sensor nor do you touch the wires. Unless of course you are made of money and have the $400 bucks to spend on a new one.
Victoria Olsgard.....I’ve ONLY used carb cleaner for 20 years ish on those things and never once had an issue with it!! I’ve even used brake cleaner on the occasion and still never had an issue with it.
Hei, I know the best is Sensor Cleaner but its hard to find from Finland. Is it ok to use Contact Cleaner ? This is good for cleaning contacts but essencially sensor is also an contact.
You need to buy more screwdrivers! The Roman emperors would have given you thumbs down using a rag to clean the sensor! You are the funniest guy on the internet... LOL😜👍
Those screws are JIS (Japanese Industry Standard) screws. You were probably struggling with them because you used a Philips head screwdrivers not a JIS screwdriver.
NEVER CLEAN THE MASS AIR FILTER THIS WAY! Clean with CRC Mass Air Flow Cleaner, any other cleaner will leave a residue and destroy the sensor. The sensor is very sensitive they cannot be touched in any way. Just replace it if it is that bad, you will replace it any way if you clean this way.
Don't be so sure... our Mazda 6 has the same MAF sensor as in this video and it looked the same, except maybe not as bad as his. My son sprayed it with CRC MAF sensor cleaner, let it dry, and it did nothing... the bulb still looked the same afterward.
Never use carburetor cleaner or throttlebody cleaner on a mass airflow sensor. It’s not worth the risk. Two completely different components with completely different cleaning needs. Very expensive part to try and see five bucks on a can of intended cleaner.
I have a question, please. I got a lovely Alfa Romeo156 1999 selespeed 2.0 lit, 16V T.Spark The problem I'm facing is: The engine starts immediately once it is cold or hot, While it is running, The RPM drops to 500 and the sprayer icon "lights on" in the dashboard, then the accelerator and gear do not activate. To overcome that stage; I should switch the "engine OFF" and start it again, then The accelerator and gear work perfectly, It happens also when I reduce the speed when there is humps or bad traffic. I changed the ECU, but it remains the same problem. Thank you for your help. Bassam
Hi Sir, You have now Sport car. And sports cars like Alfa and BMW have a LOT of many complex issues...And repairs are Costly ! And sometimes impossible to fix ! Sorry Sir. I recommend that you replace your car to Lexus.
Hi I have Lexus gs300 2007 and I would like to ask if this sensor can cause the code p0430 and please any tips to sort out this problem thx in advance Peter
Commenting on this video is FREE, but if you have technical questions for me, I charge a small fee for answering them, normally 5 USD $ per question. I am a true Technical Professional, Black Belt in engineering and The Car Doctor! Enjoy and ask. I'll answer professionally. So, if you have question: You pay 5 USD $ via the THANKS button below the video to me. Add user your name to text line. Make the payment and I will then give you a professional answer.
My toyota yaris vehicle every airfilter clean and fixing time showing engine warning light then running time automatically off the warning light what happen please tell me
The video does not start with the disassembly of the overall unit and does not end with reassembly so that you do not know where you are. Is that the air cleaner housing upside down? Who knows?
@@PeterFinnTheCarDoctor Thank you! Sorry, but for novices like me, it helps to see every single step. For a pro like you, it may seem silly to ask to go from point one. Thanks for replying. I do like your video and teaching technique. Best, Wishes, Reuben
Reuben Vabner.....if you can’t figure out how to take off the air filter housing, you prolly should hire someone with experience to help you with this.
I found it better to just buy a new MAF sensor for my 2002 Rav4 instead of trying to clean the MAF with some over-the-counter MAF cleaner. The cleaner was $13 and a new MAF sensor was $33 so I just opted out for the new MAF sensor instead.
Hi pteter...bro how r u.. i am from pakistan i have a car which is toyota corolla 2014 manual transmission so it has rpm up down problem and vibration of engine.. many time i fix it but it is return same. Instead i load extra power like as head lights on or use of pwer window turn of stearing it vibrate instead i change new battery.. so plzzz tell me solution
I have a 1985 Toyota Factory 1 Ton Pickup I drove it for years Ok . In December 2006 I drove it throw a deep water puddle & it die'd . It has Not ran right since ! You try to start it . It starts for less the 1 Sec & die's! you let off the key & try to start it again . it starts for less then 1 Sec & die's ! It does This every time you try to start it ! I have replaced the { fuel pump, fuel pump screen , Fuel Filter .Fuel Pump Regulator . } . I took the gas tank off. & cleaned it . { it will run as long as you spray gas in to the Air Cleaner } you Stop It Dies ! today is 4/27/2018 I can find No One That Can Help Me! I have been trying to fix it . Now I will say that 2 times over the years I have got it to start & run till I shout it off ! & it did restart ! But I went out the Next Day ! & It would Start for Less then 1 Sec & Die ! I Love this truck Please Help Thanks George
Hi, you might have some cables in corrosion, or some hoses are loosen. Also some electric components could be bad. So, you have A big Mess ! Sorry my friend ! Water can kills even Toyota and Rambo too.
Firstly, they only cost about $20 in the US. Secondly, you should never touch a MAF Sensor and never use Carb cleaner. Only use MAF Sensor cleaner. Everything you said and did was wrong.
$20 that's a b******* lie try up200. matter what type of vehicle you have. I had a 2000 Silverado and it was about $100 for a MAF sensor. now i have a 2013 chevy Silverado and a 2014 GMC Yukon Denali the maf sensor for them are over $20
You are bozo. Carb cleaner is too caustic for MAF Sensor. Should use spray MAF Sensor cleaner for this purpose. Also, spray sensor inside, but don’t clean with cloth!
Jack Hirsch, Jr.....as I posted before. I’ve used carb and even brake cleaner for 20 years. And ever once had an issue with it. And also seems this man’s car is fine too. So speaking from experience once again our weighs speaking out your ass!!
Lots of videos on youtube suggest you do not touch the maf sensor when cleaning.Just spray and let it dry. What you did was quite detrimental to that thin wire on the maf sensor.And use maf sensor specific cleaner.
I cleaned the sensor next to the kitchen sink.
I used mass airflow cleaner and left the component on the drainer.
My daughter,later, came into the kitchen, saw the component and thought it was a dirty part of a food mixer.
She put the sensor into the automatic dish washer.
The next morning I found it, double cleaned, I wasn't very happy, but put it back into the car.
It worked well.
Never leave anything around with other people in the house.
Wise words to live by
LMFAO
😂
Thanks for the good instruction video. After 222198 km my Prius1 start for 20 seconds and than shut down. I cleaned the mass air flow sensor and the throttle body housing in it runs like a new one. Thanks a lot !
MAF is about $70US in USA. Great video thanks for detail.
Thank you Peter, and thank you for your effort speaking English, it is my first language but I’ve always heard English is difficult to learn
Peter keep up with the good videos on old Rav4 a lot of people have these cars
Thank You, Great to hear. :-)
Do not used carbu cleaner, bro..used CRC mass air flow sensor cleaner...ok..!!
carb cleaner and brake clean work as well
every other video says mass air flow cleaner only
Bro thank you so much you helped me out!
great Peter, thank you ...
Thanks too. :-)
Thank you Pete
Thanks You for comment. :-)
U should not touch that thin wire. Just clean it with spray and let dry that its own. Keep 30 min do not put into ur car. After 30 min u can again install that.
It helped me. Thank you!
You're welcome!
I am your subscriber from UAE, really informative vedio
Thanks and welcome
Good video, very educating. Problem of taking the sensor off the connector, strength of fingers do not work. Use a rubber hammer and small straight screwdriver to chip it off, very softly. Once it was off, replacing by a new unit would be very easy.
His voice is awesome
You make my day... very good.. 😀
Awesome video Pete! I cleaned my MAF sensor and my Camry runs great. Thanks! I just subscribed! 🤘🙂🤘
Hi and Thanks for feedback. :-)
You keep pointing to the wire with the bulb on the top of it. That wire is not the MAF sensor it's the IAT. ALSO spraying carb cleaner on a MAF will melt the plastic cover on the wires and resistors - TERRIBLE VIDEO
Are you out of mind to use Carborator cleaner on Air Flow Censor ?
Noted
Advice: some people say if you disconnect the MAF sensor and the car dies, that means the sensor is good. This is not true. I spent few hundred bucks until a good mechanic told me it is untrue. It turned out I needed a mag sensor which I bought on eBay for less than $15.
Ok
What is a “mag” sensor? Or is that supposed to be MAF?? Just curious for my own info. Thanks.
I have a 2000 Toyota Camry. I just got it. It drove beautiful when I 1st got it 6 days ago. The motor was so quiet you couldn't even hear it running. Now, 3 days ago it started shaking real bad, staling, making a pinging noise, and the breaks are stiff. It's had to push them down. The oil and tran fluid look great and are full. I'm going to clean the sensor today and change spark plugs. It's not over hearing either. What do you think could be the problem? Also, put a new battery last night. Thank you in advance😊
Screws on Toyota cars that are made by Toyota do not use Phillips screws , they use JIS standed screws and need JIS screwdrivers to undo and tighten them or you risk damaging the screw head , if you do not have a JIS screwdriver use the the one provided in the toolkit in the boot of the car .
This guy is right use mass air flow sensor cleaner only if you can get it. If you can get that you won't need to brush at all. If you can't get it carburetor cleaner will work but you want to let that sensor dry for at least 30 to 45 minutes before reinstalling it. Carburetor cleaner will leave a small residue on your sensor but it still should fix your problem. Spend a $10 on a can of mass air flow cleaner period and don't brush it
👍
Hello Peter, I might try that, what could be the issue if my camry 2001, 4 cylinder lags in acceralation, the RPM needle goes to number 3 rev when it goes into the next speed, and the sound it makes is like a stuck sound like if it has air stuck, like a mini-boom sound and the sound comes from under the fuses around the right corner of the air filter, what's your take? I'm thinking probably the throttle fuse? Anyways, thanks!
Hi, how much You have miles?
Peter Finn it has 195,351 miles on it, because it loses horsepower I thought it was the catalytic converter, so I got that change, then I have the camshaft position sensor change, then the air filter and spark plugs but none of that worked, can you give any tips?
Zemorah Ledesma pull the vacuum hose coming out from your fuel pressure regulator if gas comes out means thats bad, it's beginning to shut all the way when your driving
Thumps up! Definitely!
I just did this and cleaned the throttle body on my wife's 4runner and as I removed the top of the intake housing or whatever you call it to disconnect the whole top from the throttle body I noticed a small black hose on the back side.The problem is it is not connected and has at some point broke from where it connected. Can anyone help me with what this is and how important it is also,I don't know if it were like that previously or happened when I started moving stuff but I dint want it to cause any issues at all. Thanks
Sorry, and Thanks for info.
U cannot touch that u can damage the sensor good for that is mass CRC mass air flow sensor just spray a decent amount on the inside and outside and wait until gets dry.
look at the ingredients for MAF sensor cleaner and it is nearly the same as Carb cleaner. In fact, there is also hexane + Petrol in CRC MAF cleaner which is meant to be aggressive. You can use, de natured alcohol, electrical contact cleaner, carb cleaner (some are aggressive apparently) or isopropyl alcohol.
Map or Maf sensor could cause longer cranking? And engine shaking and vibrating?
Yes
you are looking at the air temp sensor. new sensor last week cost me 19 dollars.
Ok
Just spray the MAF with MAF cleaner, period. Don't use Carburator cleaner, too strong!
You do not use carb cleaner on that sensor nor do you touch the wires. Unless of course you are made of money and have the $400 bucks to spend on a new one.
Thanks for info. :-)
Victoria Olsgard.....I’ve ONLY used carb cleaner for 20 years ish on those things and never once had an issue with it!! I’ve even used brake cleaner on the occasion and still never had an issue with it.
BTW, you can get the same Denso MAF sensor on rockauto for about $65.
Hei, I know the best is Sensor Cleaner but its hard to find from Finland. Is it ok to use Contact Cleaner ? This is good for cleaning contacts but essencially sensor is also an contact.
Everytime I refuel at the gas station my car stalls the 1st time and starts the second time, will replacing my air flow sensor fix the problem? Thanks
MAybe
also check the diverter valve and never over fill the gas tank
check your evap system my bro if you did not treat your problem
He's looking for dirties.
I'm always looking for dirties.
Not that hard to find under the hood.
You need to buy more screwdrivers! The Roman emperors would have given you thumbs down using a rag to clean the sensor! You are the funniest guy on the internet... LOL😜👍
why you didn't use cotton ear buds instead of clothe
Love the accent!!!!
Thanks 👍😀
Those screws are JIS (Japanese Industry Standard) screws. You were probably struggling with them because you used a Philips head screwdrivers not a JIS screwdriver.
👍
does this sensor cause the p0135 code or is it the o2 sensor
MAF sensor code is P0102. P0135 has something to do with the O2 sensor.
Is this the acr30 2.4 gasoline engine ?
NEVER CLEAN THE MASS AIR FILTER THIS WAY! Clean with CRC Mass Air Flow Cleaner, any other cleaner will leave a residue and destroy the sensor. The sensor is very sensitive they cannot be touched in any way. Just replace it if it is that bad, you will replace it any way if you clean this way.
Noted
I will try to clean mine a 2000 es300 , but lucky it is only $13.50 for a new denso one on ebay
your accent is awesome
You never should use carburetor cleaner
Ok
I used to love going out and finding "durties" lol
Where did you learn this ....
So many people ask why your using curb cleaner ...
Maybe you should consider removing this video please .
carb cleaner works fine, the people making these comments are keyboard warriors who dont work on their cars
@@samsonn25
I was a certified automotive technician I never used Carb cleaner on a MAS. BIG MISTAKE!
My name’a borat. Jk excellent video
Ok and Thanks !
You should never have to touch the wires with cloth if you buy proper cleaner.
Don't be so sure... our Mazda 6 has the same MAF sensor as in this video and it looked the same, except maybe not as bad as his. My son sprayed it with CRC MAF sensor cleaner, let it dry, and it did nothing... the bulb still looked the same afterward.
😳 Nothing should touch the wires, only use mass flow sensor cleaner!
Never use carburetor cleaner or throttlebody cleaner on a mass airflow sensor. It’s not worth the risk. Two completely different components with completely different cleaning needs. Very expensive part to try and see five bucks on a can of intended cleaner.
Good 👍
Haha....awesome
I have a question, please.
I got a lovely Alfa Romeo156 1999
selespeed 2.0 lit, 16V T.Spark
The problem I'm facing is: The engine starts immediately once it is cold or hot, While it is running,
The RPM drops to 500 and the sprayer icon "lights on" in the dashboard, then the accelerator and gear do not activate.
To overcome that stage; I should switch the "engine OFF" and start it again,
then The accelerator and gear work perfectly, It happens also when I reduce the speed when there is humps or bad traffic.
I changed the ECU, but it remains the same problem.
Thank you for your
help.
Bassam
Hi Sir, You have now Sport car. And sports cars like Alfa and BMW have a LOT of many complex issues...And repairs are Costly ! And sometimes impossible to fix !
Sorry Sir.
I recommend that you replace your car to Lexus.
I love those cars , I used to sell them , love the throttle blipping
What's wrong with your mass air sensor?
I measure mass air flow rate with obd2 scan tool and it shows 1.85 g in idel . Is this rate normal ? . My car Toyota yaris 2014 1300 cc auto .
Sounds Ok
Yesterday i wash that sensor with petrol and it is fine now..
Hi I have Lexus gs300 2007 and I would like to ask if this sensor can cause the code p0430 and please any tips to sort out this problem thx in advance Peter
Commenting on this video is FREE, but if you have technical questions for me, I charge a small fee for answering them, normally 5 USD $ per question. I am a true Technical Professional, Black Belt in engineering and The Car Doctor! Enjoy and ask. I'll answer professionally.
So, if you have question: You pay 5 USD $ via the THANKS button below the video to me. Add user your name to text line.
Make the payment and I will then give you a professional answer.
My toyota yaris vehicle every airfilter clean and fixing time showing engine warning light then running time automatically off the warning light what happen please tell me
Toyota MAF sensor less than $ 50.00 on e-bay Real Toyota Part.
i got one from a dealer for 135
maybe cheaper on ebay but i dont trust ebay
Mass air flow cleaner is the only thing that is recommend to clean the MAF sensor. Not Carburetor cleaner and absolutely no Brakes cleaner.
thanks Pete
His Sir, and Thanks for info. :-)
It's crazy to see you cleaning it with cotton or tissue paper ?
Both!
How to connect wiring of maf sensor at the diffrent color of socket to the original wire
Good Comment 👍👍👍
I had the exact same problem with that connector on a 1MZ-FE. Difficult to detach.
Good comment, me too 👍
peter finn, you are an idiot.@@PeterFinnTheCarDoctor
Sensor is 103 bucks at Advance Auto.
The video does not start with the disassembly of the overall unit and does not end with reassembly so that you do not know where you are. Is that the air cleaner housing upside down? Who knows?
Ok and Thanks.
@@PeterFinnTheCarDoctor Thank you! Sorry, but for novices like me, it helps to see every single step. For a pro like you, it may seem silly to ask to go from point one. Thanks for replying. I do like your video and teaching technique. Best, Wishes, Reuben
Reuben Vabner.....if you can’t figure out how to take off the air filter housing, you prolly should hire someone with experience to help you with this.
Ok to use electric contact cleaner ?
Yes 👍
I found it better to just buy a new MAF sensor for my 2002 Rav4 instead of trying to clean the MAF with some over-the-counter MAF cleaner. The cleaner was $13 and a new MAF sensor was $33 so I just opted out for the new MAF sensor instead.
Good comment. Thanks 😁👍
This video help full thanks
Thanks 👍
Hi pteter...bro how r u.. i am from pakistan i have a car which is toyota corolla 2014 manual transmission so it has rpm up down problem and vibration of engine.. many time i fix it but it is return same. Instead i load extra power like as head lights on or use of pwer window turn of stearing it vibrate instead i change new battery.. so plzzz tell me solution
DO NOT USE CARB. CLEANER ON MAF SENSOR! Other then that great video
Thanks for the tip
The MAF costs anywhere between $75 and $125 new.
Good comment, me too 👍
"cable shocked" :D
Hi and Many Thanks for feedback. :-)
is this Borat?
No, sorry
Also could use Q-tips to clean sensor.
For the love of God, Do NOT use Carb cleaner on your MAF Sensor! ONLY use MASS Airflow Sensor Cleaner!
400usd for some plastic and 3 resistors? 😂 I think someone is stealing you 🤣
Good point !
2000 V6 Camry use a different MAF sensor.
I have read your post, good comment 👍
Yes I'm having trouble with my Cantunderstandawordyouaresaying sensor.
😂😂😂😂😂
But WHY maf cleaner....safe for plastics AND leaves no residue...thats why
I have a 1985 Toyota Factory 1 Ton Pickup I drove it for years Ok . In December 2006 I drove it throw a deep water puddle & it die'd . It has Not ran right since ! You try to start it . It starts for less the 1 Sec & die's! you let off the key & try to start it again . it starts for less then 1 Sec & die's ! It does This every time you try to start it ! I have replaced the { fuel pump, fuel pump screen , Fuel Filter .Fuel Pump Regulator . } . I took the gas tank off. & cleaned it . { it will run as long as you spray gas in to the Air Cleaner } you Stop It Dies ! today is 4/27/2018 I can find No One That Can Help Me! I have been trying to fix it . Now I will say that 2 times over the years I have got it to start & run till I shout it off ! & it did restart ! But I went out the Next Day ! & It would Start for Less then 1 Sec & Die ! I Love this truck Please Help Thanks George
Hi, you might have some cables in corrosion, or some hoses are loosen. Also some electric components could be bad. So, you have A big Mess ! Sorry my friend ! Water can kills even Toyota and Rambo too.
Google Engine Hydro lock, sounds like that to me
Firstly, they only cost about $20 in the US. Secondly, you should never touch a MAF Sensor and never use Carb cleaner. Only use MAF Sensor cleaner. Everything you said and did was wrong.
$20 that's a b******* lie try up200. matter what type of vehicle you have. I had a 2000 Silverado and it was about $100 for a MAF sensor. now i have a 2013 chevy Silverado and a 2014 GMC Yukon Denali the maf sensor for them are over $20
Borates brother
I have read your message, Thank you 😀👍
Anyone can do this! Just use the right screwdriver it's easy.
You are right. :-)
How can we check if my car Air flow sensor is working or not?
I have read your message, Thank you 😀👍
u should use contact cleaner or alcohol.. dont use carb cleaner
Noted
$400 US ?? Woow uumm i just got a BRAND NEW one for $80 at a large auto parts store
I have read your message, Thank you 😀👍 Please Join my member.
I have a bad habit breaking plastic parts in cars
Noted 👍😀
I don't believe they cost $400
ruclips.net/video/abm308NYMX4/видео.html
If you listen long enough it makes less sense as time goes on.
This guy sounds like an Indian Steven hawking!!
Thanks for comment. I appreciate 👍😃
Manual from Faulty Towers. Car doctor my ass
Tioght like a Tioger
Hi sir ,can we use gasoline to clean sensor.?
that only $30 not that much
Ok
$3 fr the cleaner $14 for a new oem part
$400 for a MAF sensor, really?
ItsAlive111 , i live in the States and can’t be that much, check the Price on Amazon
Same Denso sensor is available on rockauto for about $65
I just bought at autozone with $81.49
You are bozo. Carb cleaner is too caustic for MAF Sensor. Should use spray MAF Sensor cleaner for this purpose. Also, spray sensor inside, but don’t clean with cloth!
Ok
Jack Hirsch, Jr.....as I posted before. I’ve used carb and even brake cleaner for 20 years. And ever once had an issue with it. And also seems this man’s car is fine too. So speaking from experience once again our weighs speaking out your ass!!
Lots of videos on youtube suggest you do not touch the maf sensor when cleaning.Just spray and let it dry. What you did was quite detrimental to that thin wire on the maf sensor.And use maf sensor specific cleaner.
Don't believe the hype. Carb cleaner is perfectly fine to use.
Can we use WD 40 for cleaning this sensor?
You doing wrong please stop it
You are doing everything wrong, Peter
You are going to say "It worked Fine". Yeah, but for how long?
Hi and Thanks for feedback. :-)
Years
Why you keep saying the same thing Over an Over again? 😂 Smh
Because he is an idiot.