Triumph 650 Motorcycle Engine Disassembly & Rebuild Part 2 - Lowbrow Customs

Поделиться
HTML-код
  • Опубликовано: 9 фев 2025
  • This video is presented by: www.lowbrowcust...
    Part 2 - With helpful tips and tricks, Todd takes a step by step walk through on the disassembly of a top end from the 1968 Triumph 650 motor. He shows you what to look for and how to know when certain parts and hardware need replaced or refinished.
    If you missed Part 1 - • Triumph 650 Motorcycle...
    Check out part 3 - • Triumph 650 Motorcycle...
    Check out part 4 - • Triumph 650 Motorcycle...
    Check out part 5 - • Triumph 650 Motorcycle...
    Check out part 6 - • Triumph 650 Motorcycle...
    Check out Part 7 - • Triumph 650 Motorcycle...
    Check out Part 8 - • Triumph 650 Motorcycle...
    Check out Part 9 - • Triumph 650 Motorcycle...
    Check out part 10 - • Triumph 650 Motorcycle...
    Check out part 11 - • Triumph 650 Motorcycle...
    Check out Part 12 - • Triumph 650 Motorcycle...
    Check out Part 13 - • Triumph 650 Motorcycle...
    00:12 Pushrod locations and what to look for if they are bad.
    01:59 How to tell if your cylinder head matches your cases.
    02:37 How to check your valves for wear or damage.
    03:10 Removal of the cylinder head.
    05:38 Start to remove cylinder base nuts.
    08:39 We took a lunch break and came back to discover something.
    09:26 Secure the tappets before removing the cylinder base.
    10:20 Break the cylinder base free from the cases and remove.
    11:17 Protect your RODS!
    12:38 Don't lose your piston clips in the cases!
    13:21 Remove tappets, tappet blocks and and inspect.
    18:00 Using a tappet block removal tool.
    20:25 How to determine if your tappets need replaced.
    21:07 How to inspect your pistons and check bore size.
    24:40 Removing the pistons from the rods.
    27:26 How to determine your pin and rod bushings are good.
    Music by:
    "What"
    Composed by: Jahzzar

Комментарии • 36

  • @gregoryackley4579
    @gregoryackley4579 8 месяцев назад +1

    Just got a 1963 bonneville on a hard tail frame, motor has not been opened since it was assembled! Doing a full rebuild and I couldn’t do it without your videos or parts from lowbrow! Love you guys

  • @MaxMeridius0920
    @MaxMeridius0920 3 года назад +3

    Man this is a great series! I don’t even own an engine to rebuild :) but I’m totally enthralled 👍🏻

  • @scottrose5012
    @scottrose5012 5 лет назад +2

    Such wonderful instructional videos, I do wish they would have had computers and videos when I was a kid. Thank you so much for taking the time to put together such an amazing demonstration for disassembly and reconstruction of the 650 Triumph motor, very educational and very much appreciated.

  • @mrchuka
    @mrchuka 8 лет назад +5

    Thank-you for going to the trouble of producing this! Much appreciated.

  • @ToddSloanIAAN
    @ToddSloanIAAN Год назад

    The the tips and roundabout discussion is incredible if you could take apart your bike top... Rebuild and all the things for a tight ride do it yourself Style, which is such a good feeling!

  • @christophercummins4946
    @christophercummins4946 3 года назад

    Once again another Super video by the master himself great work Buddy love watching you

  • @CarlBoyette
    @CarlBoyette 2 года назад

    Great detail! I am getting ready to rebuild a 650 and this is just what I needed!

  • @douglasallen3273
    @douglasallen3273 7 лет назад +2

    This is a great help to me building my 1967 triton. Can't wait for part three

  • @GrahamPWhite
    @GrahamPWhite 3 года назад

    Great information, full of knowledge. Thank you for your time and trouble in sharing your skill with us.
    It has been so helpful to my project. The facts you give are not found in normal manuals.

  • @dieselscience
    @dieselscience 6 лет назад +7

    "Something very flat" ... I LOVE using a 3/8 thick piece of glass for that.

  • @theisdahl
    @theisdahl 7 лет назад +2

    Great video guys. Can't wait for a part 3

  • @michaelsmith2733
    @michaelsmith2733 Год назад

    I had two Triumph 650's back in the early 70's really liked them until they broke down, which was often. They were both from the 60's, I wish I had this info back then. Sure would have helped a whole lot.

  • @brentinchley4798
    @brentinchley4798 8 лет назад +3

    You guys are awesome I can't wait to build my old school chop and get some parts and advice from y'all

  • @andrewritchie1699
    @andrewritchie1699 8 лет назад +2

    Another excellent video. Thank you.

  • @pauliebots
    @pauliebots 4 года назад +1

    Every mechanic always says mark which push rod goes where. I always wondered why? Even if they are different aren't you going to set the valve clearance anyway?! Nice to hear you say what you did.

  • @robertboykin1828
    @robertboykin1828 3 года назад +1

    fitting piston pin, check with oil and without.

  • @HugoRenaultFilm
    @HugoRenaultFilm 7 лет назад

    Beautifully explained my friend. Keep up the good work.
    Cheers from Brasil.

  • @fredgrove4220
    @fredgrove4220 5 лет назад +1

    As far as I am concerned, if I am working on an engine that I don't know, I would never just do a top end job. Have to do the bottom end and clean out the crank sludge trap, Triumph, BSA and Norton.

  • @DeeInTheHouse
    @DeeInTheHouse 7 лет назад +1

    Great videos, thanks !!

  • @BarchettaValveAmp
    @BarchettaValveAmp 7 лет назад +1

    Excellent.

  • @fredgrove4220
    @fredgrove4220 5 лет назад

    The casting number on the head , HDA, denotes it came from High Duty Alloys of Redditch in Worcetershire.

  • @salisburysteve3104
    @salisburysteve3104 8 лет назад +6

    Part 3!!!!!!!!!!!!!!!!!!!!!!!!! xoxo

  • @639viablecarrot
    @639viablecarrot 2 года назад

    My friend is it worth putting the pistons at TDC and measuring the gap in the top ring before removing the barrel?

  • @derrickjohnston7181
    @derrickjohnston7181 6 лет назад

    got to hammer cam blocks in t100 500 any advice be helpful guess will see if follow .thanks great videos..Also would a 650 motor fit on a 500 frame.? t100 1967 frame xone choped have a 64 frame and motor that match so hope some day do some trading for 650 motor.

  • @lovingmylifeasIage6741
    @lovingmylifeasIage6741 2 года назад

    My tappets doesn't have the oiling holes and it doesn't have the cross drilling for any oil. My motor is suppose to be a 71 T120R but it has a 65 head and I guess it has a 65 cylinder jug. I had a piston grenade on me and it looks like the rod ceased to the crank.

  • @jeremylinton6237
    @jeremylinton6237 5 лет назад

    EXCELLENT!!!!!!!

  • @raykev27
    @raykev27 5 лет назад

    TOOK MY TAPPETT BLOCKS OUT BUT HAD NO GROVE TO ALLOW FOR SEAL O RING . IS THIS RARE OR TAPPETTS DIFFERENT FOR ROUTT CYLENDER HEAD ??

  • @fxfoxer
    @fxfoxer 8 лет назад +1

    so when can we expect part 3?

  • @VndNvwYvvSvv
    @VndNvwYvvSvv 6 лет назад +1

    Great videos! Thanks! But... "no need to figure out which one goes where..."
    WRONG.
    Always keep then indexed just like lifters, lobes, and rockers. It might not be as significant, but it matters if you're doing it right.

  • @kevretallick
    @kevretallick 4 года назад

    What about the ninth head bolt? It was mentioned in part 1 but not removed to take off the head.......

  • @davidmackrill5611
    @davidmackrill5611 16 дней назад

    Always put the pushrods back in the same place .

  • @9traktor
    @9traktor 7 лет назад +1

    They don`t build beautiful engines like that anymore...

  • @rajinirekha861
    @rajinirekha861 3 года назад

    Hi I am from India small daughter I am facing tiger it het working you clarify thank you

  • @sebasroy
    @sebasroy 4 года назад

    "There's more than one way to skin a cat"