Yea. It wont. No mention on the evap routing, wiring harness extensions, cutting of the non welded joininh tab on the fuel rails, then casually mentions new hood or motor lowering at the very end. It's just like Dr.Strange said, "The warnings come *AFTER* the spells." 🤦🏾♂️
Hey man I need your help, beside the Y-Harness what other parts did you need to complete the installation of the Cobra Jet? Did you still buy the Boss 302 install kit? Thanks.
@@kylebrandon4958 Even better so with that and the Y-Harness you were set? btw was the fuel grade hose the one they sell in LMR or did you buy it yourself? Thanks for responding
@KINGKJ2REAL bro please tell me how the heck you do the custom tune from lund, like idk how to pick it or anything, I'm gonna be putting on longtube headers catless, injectors for e85 and I want to do the cobra jet intake manifold with the twin 65 or vmp twin 67 throttle body and a pmas cold air intake, If this is too much my bad I just want to order this stuff rn but don't know how to get the tune ordered because it's confusing af
Well I have a custom tune on the car when I bought it and I have an sct x4 tuner device on hand already too, so when I'm trying to order the tune it's confusing the shit out of me tbh
Awesome video guys. It was very helpful! Do you recommend OPG when going with this setup on my 2014 5.0 or should it be safe as long as I stay off the rev limiter! 🇺🇸
That's becuase they skipped steps and did too many jump cuts. Hopefully you've found the problem, if not there is an evap hose that is under the master cylinder, it's a problem for automatics. Apparently you have to disconnect and cap it. Try searching mustang forums.
They should make a converter that plugs into that harness so you don’t have to pull pins, just plug it into one end and it will plug into the new harness connector on the other. Much better for the customer.
Hey Bill why won't this fit for 2017 ford mustang gt 5.0 with automatic transmission ?? Is it because of the hood clearance?? Because companies do make the scoop hoods waiting for your answer thanks brother
If lowering the motor on a 2015 for fitment what does that do to the driveline angles especially if you’re running a one piece carbon fiber driveshaft?
So I saw that this only fit for 2011-2014 mustang 5.0 but video says that it fits until 2022 so is there any adjustments or do I need to do anything inside the car/engine in order for this intake manifold to fit on 2018+ 5.0?
Hey Bill, I have a 2019 Mustang GT and I am looking at several oil separators. Which oil separator would you recommend? And is one oil separator sufficient? Thanks!
I would recommend at least the passenger side since that will do a majority of the work. I like the oem look of the Ford Performance but I prefer the ease of draining the JPC. Any of them will do the job.
Have been looking for a complete list of parts/build sheet/kit for CJ install on a 2016 GT PP Premium, manual. Anyone know of something like this, thanks? Stay safe.😷
Product info:
www.cjponyparts.com/ford-performance-intake-manifold-cobra-jet-manual-transmission-5-0l-2011-2020/p/M9424M50CJA/
I really have a feeling if I try this install at home I won’t be…..back on the road in no time 😂. Bill makes it look easy lol.
exactly. My car would at least be sitting in the garage for 2 days.
@@Meechmanbinotook me 3 hours bro🤣
Yea. It wont. No mention on the evap routing, wiring harness extensions, cutting of the non welded joininh tab on the fuel rails, then casually mentions new hood or motor lowering at the very end. It's just like Dr.Strange said, "The warnings come *AFTER* the spells." 🤦🏾♂️
Now that I would like to do. Sadly I turned 70 today and money is tight
70 is just a number! Happy birthday!
Happy bd....Never to old...Never to late...Get yourself a coyote and let her rip!
Good video, but to cut time I ordered the VMP 11-17 throttle body Y harness so no repinning was necessary. Part number from VMP is VMP-INM028
Hey man I need your help, beside the Y-Harness what other parts did you need to complete the installation of the Cobra Jet? Did you still buy the Boss 302 install kit? Thanks.
1nespower no I did not buy the boss install kit as it is not needed. Just some fuel grade hose and a couple of 1/2 or maybe smaller hose clamps.
1nespower you can hit me up on Instagram @onemurdereds550 and I’ll shoot you pictures if need be
@@kylebrandon4958 Even better so with that and the Y-Harness you were set? btw was the fuel grade hose the one they sell in LMR or did you buy it yourself? Thanks for responding
1nespower bought it at Oreillys
"Running a breather Because Race Car" LOL I LOVE IT!!!
I love it. I miss all my mustangs.
Now it looks like a proper cobra
TOTALLY AWESOME UPGRADE!!!! THANKS FOR SHARING!!!! I LEARNED SO MUCH!!!! ONE BADASS MUSTANG!!!!
Running a cobra jet on my 2016. Cut the back of the hood and it fits fine
@KINGKJ2REAL hey bro how much and how do you get the tune for this install?
Jeremy Ortiz / thatblue5oh
Bought used
Installed my self
Lund tune
@KINGKJ2REAL bro please tell me how the heck you do the custom tune from lund, like idk how to pick it or anything, I'm gonna be putting on longtube headers catless, injectors for e85 and I want to do the cobra jet intake manifold with the twin 65 or vmp twin 67 throttle body and a pmas cold air intake, If this is too much my bad I just want to order this stuff rn but don't know how to get the tune ordered because it's confusing af
Jeremy Ortiz / thatblue5oh just go to lund website
Order Ngauge and custom tune
They ask for your car info and mods
It’s simple bro
Well I have a custom tune on the car when I bought it and I have an sct x4 tuner device on hand already too, so when I'm trying to order the tune it's confusing the shit out of me tbh
nice job bill!
Awesome video guys. It was very helpful! Do you recommend OPG when going with this setup on my 2014 5.0 or should it be safe as long as I stay off the rev limiter! 🇺🇸
Can't wait to get mine and install it with the new injectors E .😉😊
How about all those ? Will it fit a automatic 🤔
Is there a part number for the new plug alone?
VMP PnP Throttle Body Y-Harness for '11-17 Coyote 5.0 L -G Style
SKU: VMP-INM035
Hope this helps.
very good video, but unfortunately, after I installed the cobra jet, an error appears Check fuel fill inlet 😢
can someone help 😥
That's becuase they skipped steps and did too many jump cuts. Hopefully you've found the problem, if not there is an evap hose that is under the master cylinder, it's a problem for automatics. Apparently you have to disconnect and cap it. Try searching mustang forums.
They should make a converter that plugs into that harness so you don’t have to pull pins, just plug it into one end and it will plug into the new harness connector on the other. Much better for the customer.
Hey Bill why won't this fit for 2017 ford mustang gt 5.0 with automatic transmission ?? Is it because of the hood clearance?? Because companies do make the scoop hoods waiting for your answer thanks brother
I've been trying to figure out this Question for some time now. Us Auto guys need some answers! Lol
Why do the product links not display this part? Can't find the actual cobra jet intake manifold for the 2015 mustang gt anywhere
If lowering the motor on a 2015 for fitment what does that do to the driveline angles especially if you’re running a one piece carbon fiber driveshaft?
Can anyone source the hardware necessary to mate the manifold to the engine? I can't find it anywhere.
Anyone know of an 03 mach 1 throttle body will bolt to this intake?
Is this available for automatic?
Will this set up fit on a 2021 mustang gt?
Id like to know also. Automatic transmission here
@@brandonramey4114 does it fit? Looking into one
What part is at about 8:24 in the video?
Hi Bill, does the last version (new purchase) of the CJ plenum fit under the 2013 Boss302 OEM strut tower brace?
Will this intake work on my 2015 mustang gt automatic
So I saw that this only fit for 2011-2014 mustang 5.0 but video says that it fits until 2022 so is there any adjustments or do I need to do anything inside the car/engine in order for this intake manifold to fit on 2018+ 5.0?
Hey Bill, I have a 2019 Mustang GT and I am looking at several oil separators. Which oil separator would you recommend? And is one oil separator sufficient? Thanks!
I would recommend at least the passenger side since that will do a majority of the work. I like the oem look of the Ford Performance but I prefer the ease of draining the JPC. Any of them will do the job.
CJ Pony Parts which one would you say perform better? Thanks!
Chi H JPC
Does CJ Pony Parts still sell the cobra jet intake manifold?
Can this be installed on a 6r80
What bolts were used for the throttle body? I have to go to a local hardware store to buy them I just don’t know what size
Nice Video, but the music is to loud.
Sorry about that
Have been looking for a complete list of parts/build sheet/kit for CJ install on a 2016 GT PP Premium, manual. Anyone know of something like this, thanks? Stay safe.😷
AJ Winstonator the 2016 will require lowered motor mounts or a different hood for clearance.
Thank you!
2011 GT - Will a custom tune be required with this intake/throttle body swap over? Thanks
Kevin Mace yes any CJ swap requires a custom tune, it will run but not properly
where can i find that intake ?
Is this a gen 1 2 or 3 coyote ?
Now just imagine if someone was able to use intake while using a Procharger or any centri blower!!
It has actually been done, Revolution Automotive used one with a Vortech on a 2013.
Will this intake work for a 5.2 voodoo motor and if so what problems will we encounter.
Yeah it’s will work ,you’ll need some Hood modification
What Mohamed said is correct. If you don't want to change hoods you can get adjustable motor mounts and you will need a custom tune.
Thank you 🙏 appreciate your response
Are this gonna work in 2020 ecoboost?
No this is for V8 coyote engines only.
Always wondered , are these available for the 6r80 15-17 trans?
Yee culona
:D
Too bad some bone head used the top of manifold as a coloring book besides that it looks like pure business💯🙌✌
Plastic and pleather . No phoe king way
I have a 2011 F150 with the 5.0L and I want to do this upgrade but I'm wondering if it will turn on a check engine light?
You most likely need a custom tune I would think but not 100% sure. I would like to know as well. 🙌✌