When you’re a female who loves vehicle and no one’s ever taught you anything and you’re learning as you go and the fact this is the current thing you’re fixing thank you both so much 🎉❤ because this single mama is all about keeping her baby safe and truck running ❤❤❤❤
The removal of the valve was very good. Other videos don't show that. Just an added note, after replacing the valve on my truck. The small hose was deteriorated so I replace it as well. This may be a consideration on yours.
Knowing my truck is over 15 years old, as I was replacing the purge valve I thought that I'd also change the hoses. The purge valve part was easy to find but it's not as easy to find a replacement hose for a 04-06 5.4L F-150.
Check small hardware stores, they usually carry different size hoses and you can just buy whatever length and snip it to length when it's on the truck. Just what I did.
Good afternoon, do you know where the upper hose that goes to the engine goes, in which part of the engine it is installed, mine broke and I can't find where it goes.
I have no codes, but my truck is running really rough once i hit about 30 mph. I notice the top hose is completely collapsed. Could this contribute to my problem?
What about p0498 i checked it with my blue driver and it says low circuit vent shut off valve but when i click on the repair it takes me to a replacement purge valve instead so which component would be the problem?
If I wanted to smoke test the system would I connect my smoke machine to the top hose going from the purge valve to the motor ? then how can I close the vent solenoid ? I dont have a bidirectional scan tool as I'm using autel md806 pro
Hello, I have an 08 Explorer and i scanned my truck and got a code: PO456. Could this code be for the same part as well or no? I just want to make sure i know what part to replace. Thanks
Does the bluedriver always diagnose a code? My car has a rough idle in the drive gear. I don't have any codes popping up so idk what is causing the shaking.
I don’t have any codes but my truck is experiencing a long crank recently and then starts up and chugs into idle and then runs fine. Could this be a potential issue?
I have a 2006 ford explorer with the code p0443 purge evaporation circuit fault, the question is if this fault is related to what the EGR valve code p0403 appears, if I change the purge valve, will the two codes disappear?
I was looking over the comments on here and I noticed that you had said you changed yours so when you change yours and then it still had the same problem did you already change your upper O2 sensor and also check your mass airflow sensor if it was connected to the upper intake all that stuff I've done all those things I just haven't changed this evap solenoid and I'm wondering if when you change yours what did you also find out you had to do to get it fixed
I have a p1450 fault on a 05 ford expedition. Could this be the cause? If so, could it also be causing misfires because the valve is stuck open? Thanks. I've been told by a shop I need a new engine.
Hello, any help would be appreciated. I too have a 05 expedition. Did this fix your issue? Also, does your engine hesitate on highway speeds? As if you have to keep punching the gas for it to maintain power
@@productive23 I haven't. I reset it, it will go a couple of days and light back up. It hasn't affected the driving, and I've been working 6 days a week since November 2020 and I just haven't had time to look into it further
Probably not - this code is for a lean condition so it may be something an air leak, clogged fuel filter, bad MAF, O2 sensor, etc Check out our video on troubleshooting lean conditions (we even do demos on this truck!) at ruclips.net/video/NQxSg-G3fOo/видео.html
@@dustincrane9311 Ford couldn’t find the part for me. Mine was falling apart and ended up I ended up using a 5/16” fuel line and reused the quick disconnects
In my truck the hose that goes from the valve to the top of the manifold gets flat like as if is stuck closed and lot letting air go thru it, is the purge valve that is bad or something else?
@@joshbrowning3488 not really... I took the purge valve off and tried to blow thru it but is closed I am guessing is stuck closed because even when I put power to the valve it still stays closed but I haven’t bought a new one since is like 100$ for a new one but this week I will, I will update when I do
Gods son Christ Jesus died on the cross for our sins so that by believing in him we can have life...belief in Christ Jesus be a free gift from the father, given to them [ through thee hearing of heth words ] whom he hath chosen for salvation....
@@LemurMonitors I'm trying to find the fuel tank pressure sensor on rock auto and not finding it, could it be called something else? Fuel pressure sensor connector?
i give yu'all high marks for your thorough and succinct manner. A pleasure to watch. Thanks
Instablaster.
Thanks! It's the first time I've seen these types of clips on hoses and I couldn't figure them out. Your instruction was clear and concise!!
You can guess how many we broke before deciding to demonstrate it
When you’re a female who loves vehicle and no one’s ever taught you anything and you’re learning as you go and the fact this is the current thing you’re fixing thank you both so much 🎉❤ because this single mama is all about keeping her baby safe and truck running ❤❤❤❤
Thanks! I was ready to cut off those hoses cuz I couldn't figure out how to remove them lol
The removal of the valve was very good. Other videos don't show that.
Just an added note, after replacing the valve on my truck.
The small hose was deteriorated so I replace it as well. This may be a consideration on yours.
Simple yet to the point and educational. Thanks guys
The video made it so easy that my 6 year old did it.
We made our own how to video
I like the bluedriver product I just wish you guys would make videos on how to troubleshoot vehicles using the bluedriver.
We have other videos in the library that deal with, when you get a chance take a look.
Knowing my truck is over 15 years old, as I was replacing the purge valve I thought that I'd also change the hoses. The purge valve part was easy to find but it's not as easy to find a replacement hose for a 04-06 5.4L F-150.
Theres tons on ebay and amazon
@@AlexBarclayCalifornia the top hose on my is completely collapsed. Will this cause bogging down when accelerating?
Mine is the same but dont know where it goes to the top hose @deransanchez3162
Check small hardware stores, they usually carry different size hoses and you can just buy whatever length and snip it to length when it's on the truck. Just what I did.
What is the name of the top hose you took off? Mine is dry rotted and I can’t seem to find the name or part number of it.
Where’s the egr valve on a 2007 Expedition 5.4 EL. Sorry. New to this DIY stuff but loving it.
I did it myself. Thank you so very much.
Without any codes how do you know if your evap purge valve is faulty? My fuel tank psi reads negative pressure anywhere from -30 to -80
Good afternoon, do you know where the upper hose that goes to the engine goes, in which part of the engine it is installed, mine broke and I can't find where it goes.
Best instruction video! Thank you!
Hi Thanks! Will this solve a P0456 code on a 2008 ford f150?
I have a 07 f150 5.4 throwing p2198. I seen another video on a 13 f150 where replacing evap solved the problem??....
Great video!
Thanks guys ..
I have no codes, but my truck is running really rough once i hit about 30 mph. I notice the top hose is completely collapsed. Could this contribute to my problem?
I have the same codes I’m going grab mine today thanks guys you just saved me a few bucks
What did your code all state
What about p0498 i checked it with my blue driver and it says low circuit vent shut off valve but when i click on the repair it takes me to a replacement purge valve instead so which component would be the problem?
You guys Rock!
what does it mean if that top hose on the valve is collapsed shut ?
If I wanted to smoke test the system would I connect my smoke machine to the top hose going from the purge valve to the motor ? then how can I close the vent solenoid ? I dont have a bidirectional scan tool as I'm using autel md806 pro
Does anyone know what does quick connect fittings are called? I need to replace the top one, but I can’t find a replacement anywhere.
thank you, the problem, it is that in my country, this piece it is not a sale, How and how much can I get it?
Hello,
I have an 08 Explorer and i scanned my truck and got a code: PO456. Could this code be for the same part as well or no? I just want to make sure i know what part to replace. Thanks
Where can I get the hoses for this part? I’ve searched everywhere but can’t find them.
What about P0443 evap emission system purge control valve circuit. That’s what my scan tools is saying
Does the bluedriver always diagnose a code? My car has a rough idle in the drive gear. I don't have any codes popping up so idk what is causing the shaking.
Right to the point thanks guy’s
What problems will this fix?
What symptoms would cause the need to replace?
A lot man, if your car has a hard start or trouble to start, or It may even be harder to start after fueling
Great video! Thank you!
Is that the only thing to throw that code?
I don’t have any codes but my truck is experiencing a long crank recently and then starts up and chugs into idle and then runs fine. Could this be a potential issue?
Very nice
Just did this and it’s easy! You guys are awesome!!!
I have a 2006 ford explorer with the code p0443 purge evaporation circuit fault, the question is if this fault is related to what the EGR valve code p0403 appears, if I change the purge valve, will the two codes disappear?
Thank you so much-
Will this fix work for a ford f150 4.6 2007 code p0451?
Having the same problem same truck
Did yall ever find out the issue? Im having the same issue same sz engine
No that is a fuel tank pressure sensor fault
thank guys i get to try that too mine?
Is it possible that it wouldn’t throw a code
Thanks guy's
Apparently not a P0446 that's also telling me the same thing?
Same truck but getting po456. Same thing?
I changed this & the light went off but still has hard to start & rough idle
I was looking over the comments on here and I noticed that you had said you changed yours so when you change yours and then it still had the same problem did you already change your upper O2 sensor and also check your mass airflow sensor if it was connected to the upper intake all that stuff I've done all those things I just haven't changed this evap solenoid and I'm wondering if when you change yours what did you also find out you had to do to get it fixed
@@armandochavez3242 on my truck it was the variable timing solenoid but on the VW & Buick it was the purge valve
good tip, thanks!!
Does anyone know the part # or name of the bottom hose with the green cap. Haven't found it on any part website or had any luck, thanks in advance.
Anyone know where the bottom hose connects to?
Throttle body
Will that shot up a po446 code
I have a p1450 fault on a 05 ford expedition. Could this be the cause? If so, could it also be causing misfires because the valve is stuck open? Thanks. I've been told by a shop I need a new engine.
Same issue, did you figure it out?
Hello, any help would be appreciated. I too have a 05 expedition. Did this fix your issue? Also, does your engine hesitate on highway speeds? As if you have to keep punching the gas for it to maintain power
What engine have your truck??
What about P0453 Ford Expedition
Do you need to reset anything after replacing the ''Vapor Canister Purge Valve''
If you are seeing the codes mentioned in the video after replacing the valve you should try to clear the codes.
would this cause a crank 1but no start situation??
What is the part number for this and where can I find it?
Can i do the other bank??
What if you replave valve and atill get code
Thanks a lot.
Does this also solve the P0446?
Oh I'm subscribing alright. I do have a question...what does your little book say for that repair, timewise? lol Come on now...1 hour...two hours? 😁
Great!😊
Thnx
Hey bluedriver will this fix p2196 code???
For P2196 your most likely culprit is a fuel injector
How bout P0456?
Does this also work for P1450- excessive fuel vacuum?
It's possible but the fuel tank pressure sensor is more likely
Did you ever fix the problem. Currently having the same issue?
@@productive23 I haven't. I reset it, it will go a couple of days and light back up. It hasn't affected the driving, and I've been working 6 days a week since November 2020 and I just haven't had time to look into it further
@@braddfinch9318 please let me know
@@productive23 I'm having the same issue with code p1450 and planning on trying this.
They are doing this at gun point
Will this fix p0171? Thanks
Probably not - this code is for a lean condition so it may be something an air leak, clogged fuel filter, bad MAF, O2 sensor, etc
Check out our video on troubleshooting lean conditions (we even do demos on this truck!) at ruclips.net/video/NQxSg-G3fOo/видео.html
Hey that makes the truck like not start up
Las mangueras donde se conectan
What is the top hose called?
Did u ever find out the name I need to replace mine
@@dustincrane9311 Ford couldn’t find the part for me. Mine was falling apart and ended up I ended up using a 5/16” fuel line and reused the quick disconnects
I had to order the hose from Ford. Description of the hose says "tube asy- fuel vapour". It is the top hose on the purge valve
@@dustincrane9311 the parts Department at Ford found the part I needed online. The part number is 5L3Z9D289A. He ordered it for me
@@willgreeninlove couldn't for the life of me find that part number, thank you for putting it out there.
In my truck the hose that goes from the valve to the top of the manifold gets flat like as if is stuck closed and lot letting air go thru it, is the purge valve that is bad or something else?
In this case it was the purge valve, if you have any other questions or suggestions please contact us any time!
Regards,
Mines doing that exact same thing. Did you find out what it was?
@@joshbrowning3488 not really... I took the purge valve off and tried to blow thru it but is closed I am guessing is stuck closed because even when I put power to the valve it still stays closed but I haven’t bought a new one since is like 100$ for a new one but this week I will, I will update when I do
@@joseuzcategui6159 What's the name of the little hose? If it is going flat, should it be changed?
Could be the purge valve like blue drive said i have not changed mine really doesn’t affect my driving
Press in hurrdd. Good ol' Canadian accent
Thanks guys I think my is connected wrong
will this fix code po446
More likely the canister vent solenoid
He sounds like Chris Fix
Sounds like him but they are two different people I assure you.
@@LemurMonitors I can assure you that it is Chris Fix.
👍
P0452
Did he say a funeral fix video
Gods son Christ Jesus died on the cross for our sins so that by believing in him we can have life...belief in Christ Jesus be a free gift from the father, given to them [ through thee hearing of heth words ] whom he hath chosen for salvation....
Any tips p0451? Already replaced gas cap
Depending on the year P0451 might actually be your fuel tank pressure sensor
@@LemurMonitors welp I just got p1450 as well
@@LemurMonitors I'm trying to find the fuel tank pressure sensor on rock auto and not finding it, could it be called something else? Fuel pressure sensor connector?