I've been doing air conditioning in Florida for 33 years. I'm 51 years old. I started doing ductwork. Got into installs indoor air quality and now. Basically I just do maintenances and service calls. And I just found your channel and I'm really loving it. It's got me a little rejuvenated for my trade. Because I'm sure as you know, you can get quite burned out, doing the same thing over and over day in a Day Out.
@@tommyjoestallings855 Hi Tommy, Just wondering if there are any jobs in Florida, having said that I'm looking to relocate from California to Orlando, FL Look forward to your reply. Thanks again.
I use the probes for maintenances and a “quick peak” after a diagnostic. I use the field piece job link set with the probes, psychrometers, and clamps. I do however use my SMAN480v for adding refrigerant and major repairs. Just makes everything easier
For the past 2 summers I've been using the Testo 550i manifold and it's very nice. But a couple weeks ago I picked up the Testo 549i probes and love them, should have got them sooner.
Thanks for sharing as this takes time getting all the angle shots then editing. I strictly use the probes due to all the critically charged units I service along with walk-in coolers/ freezers that you can monitor the box temp when adjusting the charge on the roof.
I’m glad you mentioned the K type ODDB sensor. I got them for my multimeter and never knew i could plug it into the manifold sweeeeeeet.. i was always wondering about that. Thank You
Awesome video. Both are good products. I use the manifold for charging or recovering. Probes are good to diagnose or just checking pressures during a maintenance. Another thing to consider is if you have the probes they're alot easier to take up on roofs or things of that nature.
Why would you want to run vacuum/recovery through a manifold. Appion speed recovery setup direct with no manifold is much faster and less possible leaks. I really dont see the need for anything other than a set of analog gauges as a backup only for a complete set of probes. Manifolds are for the old timers IMO
@afbigfish1 Recovery on most systems doesn't even take 10 minutes through standard hoses on a manifold (at least up to the 15-20lbs I'm used to). The vacuum takes the longest, but that's mostly a limitation of the vacuum pump, not the pipeline. I buy a lot of shit the veterans in my company sneer at, but I'm not worried about a 5 minute difference in a vacuum when I wouldn't gain anything by losing the manifold.
Probes all the way. I have FP, but the JB wireless with the displays on the probes looks pretty nice. I keep a stubby for recovery. Analog manifold in the shop, collecting dust.
Charging mininsplits in the winter is easier with a digital manifold. I don't have one yet, but looks like I will need one going forward. Plus with this A2L stuff coming...
Great tips on the Fieldpiece digital manifold gage set & the different ways you can use it. Yes, you can do a more in-depth video on the Fieldpiece wireless probes & the digital gage as well. I am ready to purchase the manifold so any & all information is helpful. The analog manifold gages seem to be very limited by comparison.
I just picked up the field piece probes but always had the first gen testos mostly for heat pumps, critical charge systems or awkward systems in ceilings (see heat pumps). I’ve always used analog gauges. My company won’t buy digital gauges but I don’t think I would either. Not a fan of screens outdoors and hate batteries dying. I’m sure those digital manifolds are nice but I like analog. Probes are nice for a snapshot of system operation for a report and quick maintenance checks while looking at a dozen units a day. Cheers!
Good video ! i Run testo 557's - Gen 1. so. never used a fieldpiece Manifold. Thanks for the Run through. Does anybody know if u can Silence that annoying beep everytime you push a button on that fieldpiece ?
Does it have R290 and R600 R290 propane R600 ios Butane because they tell you you need new gauges for these refrigerants but if they are in the manifold they should be able and capable of doing what you want
Can you use the wireless probes on a 410A system then go to your next job and use is on a R22 system without a problem? Thanks for your videos. God bless
What multi tool and flashlight do you use in that brown patch thing that you have on your belt? I've been working on reefer units on the end of railcars for 20 years, but I want to get into your line of work. They only let us do mechanical stuff. No refrigeration stuff.
I had no luck with the fieldpiece manifold, and got a classic runaround trying to have them give me an exchange or repair after 13 months. I only have their fieldpiece probe/clamp set up and have not used them as of yet. The yellow jacket is too expensive. I got the Testo 550 for $390 and the hoses for free.
Appion do one with a 5/16 connection point to the unit and have a 1/4" attachment point for your hose and a 1/4" outlet on the top for probes/micron gauge. I bought mine off Amazon, it's great. Fieldpiece also have an interchangeable 5/16 adaptor for their valve core removal tools. It is a seperate part.
Is this guy serious I'm going to buy a separate valve core depression tool's not when my appion valve core removal tool does the same thing turn the valve core out a little bit and you get pressure on the gauge
Could you make a separate video on the manifolds and how to use every feature it offers
I've been doing air conditioning in Florida for 33 years. I'm 51 years old. I started doing ductwork. Got into installs indoor air quality and now. Basically I just do maintenances and service calls. And I just found your channel and I'm really loving it. It's got me a little rejuvenated for my trade. Because I'm sure as you know, you can get quite burned out, doing the same thing over and over day in a Day Out.
That’s what I call…… experience. The repeated process is how we gain knowledge and at the end we become better everyday.
@@tommyjoestallings855 Hi Tommy,
Just wondering if there are any jobs in Florida, having said that I'm looking to relocate from California to Orlando, FL
Look forward to your reply. Thanks again.
Thank you for making this video. I’m currently in HVACR school, so this explanation helps a lot
Yes please make a video on the apps and the pros and cons of each. I'm in HVACR school now and want to use the better app.
Measure quick is the best for newbies
I use the probes for maintenances and a “quick peak” after a diagnostic. I use the field piece job link set with the probes, psychrometers, and clamps. I do however use my SMAN480v for adding refrigerant and major repairs. Just makes everything easier
For the past 2 summers I've been using the Testo 550i manifold and it's very nice. But a couple weeks ago I picked up the Testo 549i probes and love them, should have got them sooner.
Thanks for sharing as this takes time getting all the angle shots then editing. I strictly use the probes due to all the critically charged units I service along with walk-in coolers/ freezers that you can monitor the box temp when adjusting the charge on the roof.
I’m glad you mentioned the K type ODDB sensor. I got them for my multimeter and never knew i could plug it into the manifold sweeeeeeet.. i was always wondering about that. Thank You
Awesome video. Both are good products. I use the manifold for charging or recovering. Probes are good to diagnose or just checking pressures during a maintenance. Another thing to consider is if you have the probes they're alot easier to take up on roofs or things of that nature.
Why would you want to run vacuum/recovery through a manifold. Appion speed recovery setup direct with no manifold is much faster and less possible leaks. I really dont see the need for anything other than a set of analog gauges as a backup only for a complete set of probes. Manifolds are for the old timers IMO
@afbigfish1 Recovery on most systems doesn't even take 10 minutes through standard hoses on a manifold (at least up to the 15-20lbs I'm used to). The vacuum takes the longest, but that's mostly a limitation of the vacuum pump, not the pipeline. I buy a lot of shit the veterans in my company sneer at, but I'm not worried about a 5 minute difference in a vacuum when I wouldn't gain anything by losing the manifold.
@@sammiches6859 Not sure about that a set of trublu hoses on any vacuum pump makes a night and day difference.
Probes all the way. I have FP, but the JB wireless with the displays on the probes looks pretty nice. I keep a stubby for recovery. Analog manifold in the shop, collecting dust.
Oh yeah they are nice but damn pricy
I'm over here still using analog manifold lol
Me too
The tools don’t make the tech but it does make your job way easier.
Charging mininsplits in the winter is easier with a digital manifold. I don't have one yet, but looks like I will need one going forward. Plus with this A2L stuff coming...
Great tips on the Fieldpiece digital manifold gage set & the different ways you can use it. Yes, you can do a more in-depth video on the Fieldpiece wireless probes & the digital gage as well. I am ready to purchase the manifold so any & all information is helpful. The analog manifold gages seem to be very limited by comparison.
I’ve been running service calls and doing a few changeouts without SMANS. I use the fielpiece job link kit and analog gauges.
I just picked up the field piece probes but always had the first gen testos mostly for heat pumps, critical charge systems or awkward systems in ceilings (see heat pumps). I’ve always used analog gauges. My company won’t buy digital gauges but I don’t think I would either. Not a fan of screens outdoors and hate batteries dying. I’m sure those digital manifolds are nice but I like analog. Probes are nice for a snapshot of system operation for a report and quick maintenance checks while looking at a dozen units a day.
Cheers!
My setup up is almost identical but I use a T with a hose with a ball valve for charging. Other then that I have the same tools and everything
Looking for digital probes with display on them. Like the fieldpiece vacuum probe.
Appion makes a Charging T that is a lot smaller then that little setup you have
Great video zack
Where can I get that charging/recovery valve integrated with a tee?
So you use one of the wired pipe clamps to get your OAT. Just clip it to the side grill of glue a magnet to the side of the clamp.
I have been a fan for many years now. Just wondering when you will have a FREE GIVEAWAY tool 🔧 😁
How do you connect/pair the wireless clamp probes to the manifold?
Does anyone know if the current fieldpiece digital gauges are compatible with new A2L Refrigerants we are moving towards?
Please do a video on both apps I have both and I’m still learning
Another thing is that the digital I think if does measure microns for vacuum, correct me if I’m wrong
Please do a video on the apps. Thank you!
What Appion core depressor has the valve?? Where can I purchase??
Dude what supply shop did you get that charging/evac adapter with shut off. I just liked and subscribed
Good video ! i Run testo 557's - Gen 1. so. never used a fieldpiece Manifold. Thanks for the Run through. Does anybody know if u can Silence that annoying beep everytime you push a button on that fieldpiece ?
Thank you for the video. Can the manifold refrigerant choice be updated as time goes on?
Does it have R290 and R600 R290 propane R600 ios Butane because they tell you you need new gauges for these refrigerants but if they are in the manifold they should be able and capable of doing what you want
Also im using Tasco Safety Valve protect from frost bite.
Where do you get the core depressors from?
Can you use the wireless probes on a 410A system then go to your next job and use is on a R22 system without a problem? Thanks for your videos. God bless
I have an had no issues.
Yes all digital gauges can you’ll be good
Make one Testo vs Fieldpeice
What multi tool and flashlight do you use in that brown patch thing that you have on your belt? I've been working on reefer units on the end of railcars for 20 years, but I want to get into your line of work. They only let us do mechanical stuff. No refrigeration stuff.
What’s your opinion about full package of Refmate 4 from Swiss Refco?
Field piece or yellow jacket digital manifold
I had no luck with the fieldpiece manifold, and got a classic runaround trying to have them give me an exchange or repair after 13 months. I only have their fieldpiece probe/clamp set up and have not used them as of yet. The yellow jacket is too expensive. I got the Testo 550 for $390 and the hoses for free.
In my opinion if you’re green you should start with analog gauges then move up to digital
what is the hose brand for 5/16 core remover？ I found it super hard to get a adapter except 1/4 to 5/16.z
Appion do one with a 5/16 connection point to the unit and have a 1/4" attachment point for your hose and a 1/4" outlet on the top for probes/micron gauge. I bought mine off Amazon, it's great.
Fieldpiece also have an interchangeable 5/16 adaptor for their valve core removal tools. It is a seperate part.
What kind of batteries does the digital manifold use?
6 x AA batteries
I just use 2 valve core removal tools.
Is this guy serious I'm going to buy a separate valve core depression tool's not when my appion valve core removal tool does the same thing turn the valve core out a little bit and you get pressure on the gauge
I just have analog gauges but put a T so I can turn my analog’s into digitals.
Rugged wow so they made a change from 2017
Wireless don’t work when you don’t have WiFi
But it’s Bluetooth
They’re Bluetooth and works up to 300 feet away. If your phone doesn’t have Bluetooth. It’s time to trade in that 1st generation Nokia.