Clean the hub mating surface rust and be sure there isn't any rust at all it's worth the little extra time. it's gonna look great ! I need to order some of those.
Well for one you have to put it to the recommended torque spec for the wheel, and two it depends on if your wheel studs are too long. Generally though, spacers are a bad idea. It's an extra point of failure and makes your hubs wear and break a lot faster because you're moving the wheel and all the weight it's holding further away from the hub which adds a lot of stress. If they aren't installed properly and come loose then youre gonna die or kill somebody. Just get rims with the correct offset for the stance you want (that also makes the hubs wear faster, but it's not as likely to fail catastrophically)
A Toyota forum probably, but i use 90 on lug nuts for a lot of vehicles if I’m not sure I’ll google it up and research for the specific part to be torqued
@@LuisManuelHdez and lots of them go down the interstate with a wheel flying off lol, read the warning label on the box of wheel spacers before installing 🤣
@@pooppoop8957Clown don't comment on what YOU don't know . I have been a tire tech for Belle Tire for 15 years we are legally not allowed to sell or install them for a reason.I know people who have used them no problems but also known people that have had catastrophic failures using them
Clean the hub mating surface rust and be sure there isn't any rust at all it's worth the little extra time. it's gonna look great ! I need to order some of those.
Put some never cease behind them I heard they’re hard to take off without it
Ko2's are sweet!!
Absolutely tuning ❤in
is the tired need to by flush with rhe spacer or does it have a small gap of 1/8 or less cause of the nut lug
Awesome !
Do the directions say lock tight or no? Seems like a good idea
No but but its an additional security
From my experience, most wheel adapters come with threadlocker. And if they don't, just add some.
What tires sizes? no rubbing?
Hey man do you just use stock studs? I’m wanting to do 1.25 or 1.5 for my Tacoma and not sure if I should change those out.
Be smart man use longer studs
I think you’ll be okay if stay within that range anything bigger you would need longer studs
10/10
good or bad?
Are they really that easy to install? Just take the wheel off drill the spacer in and put the wheel back on
Well for one you have to put it to the recommended torque spec for the wheel, and two it depends on if your wheel studs are too long. Generally though, spacers are a bad idea. It's an extra point of failure and makes your hubs wear and break a lot faster because you're moving the wheel and all the weight it's holding further away from the hub which adds a lot of stress. If they aren't installed properly and come loose then youre gonna die or kill somebody. Just get rims with the correct offset for the stance you want (that also makes the hubs wear faster, but it's not as likely to fail catastrophically)
Your comment really helpful
What's the purpose of wheel spacers?
any problems with the wheel spacers so far?
No!
I’m here for the loctite
Cual es el torque Adecuado para ford f150 2014?
Yo también tengo un F150 2014, el recomendado es 140 ft-lbs, pero en el mio tengo también un level kit con 35s
We’re did you find the torque spec for 90 ftlb?
A Toyota forum probably, but i use 90 on lug nuts for a lot of vehicles if I’m not sure I’ll google it up and research for the specific part to be torqued
Whats that glue-marker for ? Can you explain
It’s loctite, more than likely blue, even though it’s in a red tube lol
Do we need car alignment after the spacer
NO!
doesn’t rub on u-turns?
No i think these tires are 11” wide
How much pounds did u set it to?
I usually set wheel studs at 90lbs
What is the benefit of this ?
Wheel Clearance for bigger/wider wheel
Wheel spacers are dangerous and not worth the headaches so you’re tires can poke out lol, buy a good set of off set wheels.
Well those are trd 4runner wheels and they dont come in different offsets than stock
Lots if people run spacers on their vehicles. If properperky installed and torqued there are no issues. He did it right.
@@LuisManuelHdez and lots of them go down the interstate with a wheel flying off lol, read the warning label on the box of wheel spacers before installing 🤣
@@jamiel3504clown don’t comment on things you don’t know
@@pooppoop8957Clown don't comment on what YOU don't know . I have been a tire tech for Belle Tire for 15 years we are legally not allowed to sell or install them for a reason.I know people who have used them no problems but also known people that have had catastrophic failures using them