Im running 14 3S 11.1v 60c (21s 88.2v max) Lipo's thru two 3000 watt my1020 motors and two ebay 72v 80amp controllers in my go kart build. I was wondering why more people are not going 77.7v, 88.2v or 96v especially on the bigger controllers. Nice vid
I would recommend more or bigger if you can. It was good for the time I used it. I moved on to a sabvoton, and now there are 2200W 45A sabvoton. packs a better punch and smoother too with pure sign wave.
Well...I got a Euro style scooter+sidecar combo from the same place that your brushless controller was made at. I plan to juice it up and use it for a grocery getter. I just hope it doesn't cause me to crash because of poor welds to the chassis or something 🤣. It's made in Guangzhou I believe.
Alireza iesanejad speed depends on your voltage. If you get voltage sag you get less speed (get a bigger battery) unfortunately I didn’t check my top speed :( I was running 22s 5p 26650 5000mah cells giving me 92.4v fully charged and fully capable of delivering the 50a to the controller.
@@mahmuttekin3882 The effictive of High Break' and 'Low Break is almost the same.Just the connection is different,The high level brake should be connected with the positive battery line That is the red line.The low level brake 2 wires can connect the brake lever directly
@@smartazz Give it a shot! I was told folks just upgrade the caps to nice 100v units and squeeze and solder the shunts. I have 3 120v lith packs from my mower I was wanting to try.
Still have my Sabvoton 72 volt controller hooked up to my 3000 watt hub motor.............run great. Trouble free
I have a Gotrax GXL with a 72 volt controller and 80 volt battery...........the torque is insane
Can I use a 96v 1500w controller on a 1000w hub motor or will it damage it?
It will work but for how long ??
Im running 14 3S 11.1v 60c (21s 88.2v max) Lipo's thru two 3000 watt my1020 motors and two ebay 72v 80amp controllers in my go kart build. I was wondering why more people are not going 77.7v, 88.2v or 96v especially on the bigger controllers. Nice vid
Lower voltage is safer :) and higher is less safe, that’s all I can think of lol
3rd speed gets 10% than at full speed?
It’s difficult to say tbh. Usually it’s 50% 75% then 100% or as the manufacturer will say 110%
@@smartazz Better to go 110% if that is one gear lol
How much current peak do you see on your display. Is that 50A enough?
I would recommend more or bigger if you can. It was good for the time I used it. I moved on to a sabvoton, and now there are 2200W 45A sabvoton. packs a better punch and smoother too with pure sign wave.
Well...I got a Euro style scooter+sidecar combo from the same place that your brushless controller was made at. I plan to juice it up and use it for a grocery getter.
I just hope it doesn't cause me to crash because of poor welds to the chassis or something 🤣. It's made in Guangzhou I believe.
Wow that ace. Be careful :)
Hi what speed do u get of 3000w running with greentime controller and what is ur battry spec pls?
Alireza iesanejad speed depends on your voltage. If you get voltage sag you get less speed (get a bigger battery) unfortunately I didn’t check my top speed :(
I was running 22s 5p 26650 5000mah cells giving me 92.4v fully charged and fully capable of delivering the 50a to the controller.
where can i buy this i cnt find any 84v+ controllers
￡44.10 | GREENTIME Sensor/sensorless Dual mode 84-96V 2000W 50A BLDC motor controller E-bike brushless speed controller
a.aliexpress.com/_u7li5u
Any link to buy it online
@@kingsfordosei8628 no sorry. Search “GreenTime inverter “
Where does the h-brake cable connect
0:42 the yellow wire at the end of my middle finger .
You connect it to your live battery terminal.
@@smartazz Yeah I know it's the yellow wire I don't know where we gotta tie it
@@smartazz do you have an instagram address. i will send a photo
@@mahmuttekin3882 upload to imgbb.com
Copy the link and send to this chat
@@mahmuttekin3882 The effictive of High Break' and 'Low Break is almost the same.Just the connection is different,The high level brake should be connected with the positive battery line That is the red line.The low level brake 2 wires can connect the brake lever directly
Hi I got the same controller 60a but rated for 1500w to 2000w can I use it with 3000w hub or not
Yes you can :)
@@smartazz will I get less power and speed with the 2000w 60a controller and 3000w motor or it same as 1500w motor if the winding is same?
Alireza iesanejad it will be slightly different if the winding is different but the speed and acceleration should stay the same I would think.
Hi how much current do you max see on your display
@@Slic-Rock got sw900 display and greentime controller and it ain't show current on the display
I don't have 5 Volt at hall red wire , only 100 mV anybody ever fixed this kind of problem? The make is a Sodial.
Join staf.uk/forum/
And start a chat. We might be able to solve this problem for you :)
Anyone pushing 100+v through these?
I could try it lol 😂 a fully charged 24s Lithium is 100.8v
I think it has 100v caps so I wouldn’t go over that
@@smartazz Give it a shot! I was told folks just upgrade the caps to nice 100v units and squeeze and solder the shunts. I have 3 120v lith packs from my mower I was wanting to try.
@@AdamOpheim ace I might make a small video on it :)
i.smarty.co.uk/Ek5WcL
Get a free month of SMARTY, and, until 16 November, £10 credit BONUS