Видео

Is there a way to manualy swich to pit mode, mine has one meter range after crash, maybe it's dead or maybe its in pitmode

Hi - thx. for make this video with JB Parallel Charging Hub -> Q: is it still the best one on the markedet, or can you recommend another ? I'm using SkyrRC Q200neo as my daily driver - is it good enough, or can you suggest a better ? Thx. in advance :) /Henrik

Just got mine 1/12/24 from Get FPV , Also have older 80-watt per channel 4-channel 3260 version, one channel display is sketchy. So now have capability of charging seven lipos at a time. Highly recommend this charger for RC fliers with average needs. Surprised how many use these to charge their Prius car batteries, etc. As far as I can tell the blue/silver is version is the same as the red "B-QUAD" version, except the blue/silver version comes with XT-60 charge cables, the red version comes with Deans type "T" charge cables. I had to order four ST-60 female to Dens male T adapters to suit all my Lipos with "T" connectors. My package did not include a charge cable with alligator clips for charging lead acid batteries.

Verdade a maior parte das pessoas não sabem isso , e metem antennas com a polarização circular. 👍👍👍

I take it no one is reading the comments on this video.

nice project bro this tabel is very good

This is a super K I C K - A S S V I D E O - Thank you for the refined education. I will get back to you. Erli Bittencourt

Bummer no sma... if so I would have ordered a couple of them

have the same charger, but no memory in the menu on mine. According to the manual, there should be a battery meter in the menu (to check IR etc), but even yours doesn't seem to hqave it. Did you find the mini USB to update the firmware of the charger? There is are a few short sentences in the manual about it, but no real info on how to...

Hello, I plugged in a LIPO 3S battery into the Balance port and could not change the setting from 1S to 3S and thought you had to hold the start button to auto detect it. I got the high voltage error and now getting Battery Check Cell Connect ERR. I tried another port and set it correctly and it works fine. I take it I fried one of the ports.

when soldering the audio to the FC uart is it to tx or rx on the FC

thank ya! still very relevant! started this mini-quad journey in 2017 haha too cheap to buy or setup the fpv system (all LOS)-- now I want to go fpv explore the freedoms we have while we still have them! sub 250g gonna take a minute at the local FPV workout kalub! I am using different fpv components but the same CL racing board; wiring should work out the same. thanks again

The prototypes are always problematic,I’m sure improvements will follow,or nobody will buy it.But it looks promising.

I have a Flysky Fs-i6 transmitter and receiver. I would like to wire the receiver to the flight controller in a way that utilizes PPM. The GND and POS wire make sense to me, but where would the signal wire go for PPM? I appreciate any help you may be able to give!

i got 4 of these.. they all are off on power output.. but all are over.. approx 1100mw on mine

Which pads do I use for crossfire

a 35A esc with 45 burst would handle it?

How do i power up this charger i see a red and black lead and a extra plug wire but nothing to plug into a wall outlet

2'' or 3'' ? Motor do you recomended

Is schematic and board files available for this board or omnibus variants?

Is there any action cam that DOESN'T distort the horizon as the camera tilts up and down?

Is this a IRC Tramp or TBS?

You you talk too much and did not show how to charge a battery

I really need a four port charger would you still recommend this one today

I’m a beginner - do you still need ESC if this has everything?

I use this board but it can't detect GPS on Arducopter. How is the wiring? What serial port should I use? I tried serial 3 & 4 but to no avail. It says bad compass health, compasses not calibrated. Only blue led on Beitian 880-Q is flashing. I tried different baud rate for GPS also.

I use crossfire on tx4 and rx4 how do i get smartaudio now

How can I control servo from cl racinf f4s

Great video thank u.

Where you been??

Sounds like you might be just down the road from where I am in Kingston, TN. I recently bought a CQ3 and was very impressed by it for charging four Hubsan Zino drone 3000mAh LiHV batteries. That battery required modding some 3S extensions to splice on some banana plug leads as the interface to the Zino charge cable. My question having now used the CQ3 on several occasions is whether you have seen consistently quick charging times? I see a wide variation of charge times which of course makes sense relative to how depleted a battery is, but I'm talking about beyond that. Most curiously, I just tried charging a battery depleted to about 50%, using a 7.2A balance charge current which is near the max for that battery on a 100W channel, and for a little over 1400mAH delivered charge capacity, it took 110 minutes versus having seen a 56-minute charge time @7A for half again the delivered charge capacity at 2141mAH. That totally makes no sense to me, so I'm hoping you might have some experience to shed light on that. At 1C, I've seen times around 90 minutes and at 2C, around 74 minutes, so that looks a little more consistent with expectations. Thanks!

Thx for this review. I dont even got a video signal out of it. It seems to work because the vtx gets hotter if i set it at higher mw-output. I dont run Betaflight but do i have to set this up somehow to make IT work?

Wonder what my mach 3 does? I used the camera ouput 5v off vtx instead of using Helio spring v2. I've not had much luck with the tbs unifrys

Steelrain I've had several tbs unify go bad and I bought a rdq mach 3 u think there close to there say so power? Any opinions? My tbs race hv is blackout and white flickers and 200mw gets me 200ft if lucky.hope it's just the vtx and not eagle micro cam

i wish that the tbs unify hv race ive had didnt die so easy maybe my luck but i remember the tbs unify hv pro never give me issues i think. also im looking at mmcx design what you think?

I'm just curious, let say i buy the 6s version, can you use it to charge 4s parallel?

Thanks for thé vidéo do you think is possible connect a gps in this fc ???

How do you enter the main menu on this cam? Holding the up button for 2 seconds only brings up the OSD menu, but not the main menu. How do I open that??

I recently got this. It only shows static screen in my goggles but I soldered it on 5V. Is it a must to get atleast 7v for it to work properly? When it's on the 5V pad it starts up and I can change channel etc. Help please :)

bearing size ?

Heya there bud, new sub here. I was curious, I have the wolfwhoop q3 pro. It says 7-26v, I have it connected to a 5v rail on my helio, Just curious if this would be underpowered

Hey old video, but have you got the barometer to work?

HELP!!! soldered the connector on the transmitter and the central signal path disappeared. Where can I get this contact? Is there another signal contact on the transmitter board?

Sir please contact me reference the RunCan Pro We would like to direct connect the can to a set of VR006 without going thru a transmitter. the hook up has me lost.Thanks ahead of time. Yes Im a newbe

Hi Steel! Did you figure out where the Barometer is?

Whats your opinion on Eachine Tx(s) vs AKK Tx(s) ? I am looking for an Airplane System; TX and RX with (reliable 1-2km Range) as a replacement for the old Lawmate 2,4Ghz System. I made the switch from 433openlrs to FrSky 2,4 thats why I have to switch the Videosystem as well. My Videogoogles are from Marek: napolskimniebie.pl/index.php/sklep/wyposazenie-fpv/obudowa-do-monitora-5-detail

Nice vid! ihave this Tx5258.The cable is 4 pin,but most cameras have 3 pins.how do i conect it?

Great post! Man can you imagine frankenstein anodizing his rooster back in the day! Operation; don't touch the sides! Wait, I think that was a date (period, era, epoch) reference...

I was wondering about how you powered the camera .... looks like you took the red and black from the camera and the red and black from the VTX and soldered them together then just solder them to the pos and neg pads on the VTX pads so all power to the VTX and camera was done on common pads for the VTX? Did I see that right?

What firmware do I need on cleanflight ? I can't get it to work