Видео

I have the exact same Motorola android G stylus 4BMP and my phone screen itself is completely cracked and broken. How would I go about it. Do I just get a brand new phone again or should I just get a brand new phone screen itself

Very informative video. I have the same issue with my fridge. Thank you. I have had this fridge for year. I do not understand why Whirlpool installed these led lights vs. light bulbs. I suppose to pay quite a bit of money for these led light!!!!

My plan is the 3 light kit and the switch 30$

It's easier to get the screen with the frame included that's what iam doing off eBay and a battery replacement

What type of bearing did you replace the bad one out with? Did you use the OEM size or a different size due to having to sand the crank?

You are a good man. Thank you.

Fantastic video! I will order the parts from Amazon. You give stellar instructions. Thank you.

Appreciate this sir!

Appreciate sharing your video, it helped me in re-attaching my broken off fender trim. Thankfully, I was able to find some aftermarket clips and not have to buy them thru Nissan Dealer.

Thank you

Can you do a video on replacing the headlight assembly

Tip. Remove food that’s gets in your way

I need to do this to replace my shutter grill on my 15.Thanks for this vid.

Excellent video!! Well done. Thank you for sharing

what was the cost for the dealership to program

Did you reset TCM after oil change?

Just curious is there a bracket that is needed to connect the bumper to the fender? I bought a 16 murano rebuilt and on one side of the vehicle the bumper is not entirely connected to the fender, seems like prior owner tried gluing the parts together which didnt work on holding them together. I removed the glue exposing the tabs on the bumper to clip onto the fender but the tabs don’t match up with the fender, they are wider than the openings on the fender. Trying to figure out how to fix that without having to replace neither the fender or bumper.

I went to a nissan dealer and they said "transmission oil change at 100k thousand miles then at every 50k miles after that

Just wanted you to know... I did what you said. Ordered my lights on Amazon - swapped out the refrigerator light and the freezer light and all three came on (even that little one at the bottom, on the refrigerator side, that I didn't swap out) I appreciate your detailed and thorough video. ❤❤

Was your transmission fluid yellow?

Thanks I'm about to drop my K-member on my 2011 GT, Oil pan got smashed by a rock or something bad (lowered), Very helpful video!

The white part under the flare are those called slide clips or pins. I'm just asking because I need to replace them

I was starting my motor and it kept cranking even after i turned it the key off! Had to unplug the battery. Lol

Best instruction by far, thank you. Does a 2020 model have the external filter? Also which internal screen for the same 2020 version? I’m at 30k and will need to do this service this summer so I’m trying to prepare.

thank you sir... a great step by step instructions.

How many quarter's did you put it back again? Thank's for the video.

Hello, how many kilometers now?

Heads up to any DIYers doing this yourself. The latest transmission strainer (larger silver filter behind the pan) (13.3 min) is now a "D" revision as can be seen at the end of the part number, 31728-29X0D. I also had to buy a new bracket part number, 310693-VXD. This only done once, unless of course, Nissan goes to an "E" revision. I found this out the hard way after ordering all of the parts and dropping the pan. I then had to scour the earth for the new bracket and drive a couple of hours to get it. Hope this saves someone some serious time and frustration.

Me ajudou bastante por aqui! Muito Obrigado!

Do you know if you were getting any of the Judder codes before you did this?

Awesome video thank you Vern!

Thanks appreciate video you made! Helped out alot. Plus the parts numbers were a plus.

Great job with the video. Lots of details that are necessary to get the job done. A happy CVT makes for a happy life! haha Take care -Glen

Thank you for the video. I don’t think the led lights are the problem but maybe something on the motherboard goes bad there made super cheap, unfortunately is not so cheap for the consumer to replace.

Amazon new resource from his original, which is no longer available. NEW 2 Pcs W10515057 & 1 Pc W10515058 LED Light SET With Tapered Lens and Bezel compatible for Whirlpool, Kenmore, Maytag, KitchenAid, Refrigerators, WPW10515057 AP6022533 PS11755866

Well done. But had a question. Maybe I missed it in the video but figured I would ask. When you dropped the pan what was the part you replaced? Is that an internal filter? I have a 2018 murano platinum. Hoping it’s the same. Need to change mine.

may i know the dimension of the base? the square part

How has this been holding out for you? I am looking to install one on my 2010 and I’m out in Texas heat lol, but relocating down to Florida next year!

Did the valve body replacement come with a CD or anything that you gave to Lokey to assist them?

Thank you for this video. So true what you're saying. They are listening.

Did this Fixed your O2 codes

Thank you for posting this! I used a 1/16" bit and the mic is no longer working AND the remote still works. I've noticed Prime Video & RUclips recommendations from conversations, was it coincidence? Nope. Last night was the confirmation, I mentioned "timberdoodle" which is another name for a woodcock and later in the evening a timberdoodle video recommendation came up in my RUclips recommendations (I was accessing RUclips through the firestick). Amazon and RUclips are apparently sharing info. I haven't done any searches for timberdoodle/woodcock on firstick or the web. I 100% sure it was the mic on the remote. They might say it's only used for recommendations. Would I ever trust them having access to my private conversations? IMO it's an invasion of privacy.

Is changing out the whole pan part of servicing or can you just change the fluid and filter?

Cant get that sound out of the same cam .in the last engine I built

The only (?) video of this product on the Tube. Very helpful. Thanks for uploading!

What is the part number

I am such a goof, I moved it in my driveway and then checked the oil and thought it seemed to be on the low side.... McFly (bonks self on forehead) I just ran it. I will go check my oil again in 30 minutes. THank you for posting this video, great lighting, great audio. And your video answered my exact question. THANK YOU!

Is there a recall on this garbage yet?

I’m going to be changing out my oil pan gasket. I am going to drop the K member mainly because I am changing out rack and pinion and front lower control arms. Why did you drop the whole K member with struts and all? Couldn’t I just unbolt the lower control arm ball joints and the outer tie rods?

Is the atf oil for this truck supposed to be annoyingly faint? Cause I checked mine it had a faint red color. But that was only I lifted it up towards the light 😂