Видео

My Workmaster 75 really is overloaded with a 12 foot shredder. I am really wishing I had looked at a Massey 4710 now. However Agco dealers are few and far between in Illinois. Plus the poor resale value of a Massey.

They won't show how hard it is to get the Cab Filter out, It's dam Hard!!!!!!!!

Good stuff

What range and gear are you cutting in? And when you bale?

Thanks for the heads up

back when you installed the hay moisture monitor in the baler, did you get a chance to use it? how did you like it?

nice tractor

Thanks bud

Out of Texas, i use Vermeer wrap on my new holland baler and I’ve put over 10k bales on that machine. Highly recommend!

Good incredible idea 👍

Great job bravo, I have new holland T4.s likeYou before Masey Best Regards

Do you have to the up curtains to keep wind from tearing the straps off curtains? I’m thinking of getting a new tm 1200

I have a 2014 T4.85 New Holland and the problem I’m having is I can lift the arms with the “draft” lever. I was wondering if you think the “linkage” to the position lever and the hydraulic lever at the back of the tractor could have been “stretched”? I can see the linkage from the back of the tractor and I can raise and lower the arms by moving this linkage but when I climb back in the tractor the position lever doesn’t raise or lower the arms. Great video and information!!

I have the same issue with my 21 NH 55 Workmaster, I have a question about how to reinstall the aluminum sleeve, once the allen bolts are loosened, where should the manual lever inside the cab be in ? The stop or off position or the on-engage position ? I reinstalled the sleeve on my tractor in the engaged position as it was the only way it would go back on that collar, however that resulted in the manual lever inside extremely tight and still not operating the engage or disengage of the PTO. I feel like it is an easy fix but I would like to know that starting process before I reinstall it again to make sure I do it correctly. Should I pull the cable like you did in the video or push it in manually without using the lever inside the cab ?

A service bulletin came out from Massey regarding the def fluid sensor. If you continue to have the def issue the dealer should come out to replace the sensor. My 4710 had the same issue and after the sensor was replaced I have not had the issue. I was told the tolerances on the sensor were changed. What speed do you bale at and what type of bailer.

How long is your 3x3 square tubing were your bale spears are on? And how do you know we’re to put your bottom brackets to hook up to your bottom 3 point arms?

Very impressive, didn't know a 100hp tractor could that.

you got screwed more like 14000 bales

Very helpful and fixed. Thank you very much and save our cost for dealership repair. My brother in law planning to send service. I did not want to send and wanted to fix asap for farm hays working. Thank you!!!

Man we’ve both came a long ways since our Workmaster! Started following you then, Workmaster 75 and a John Deere 430, now a T5 100 and a Kuhn 2160

Do you mind sharing where you found the used TM1200 at that price id love to buy a new one but 52k is tough to do right now. Thanks

Holy smoke your flyin

Hi Chris ... Always awesome to see a new video from you! I've never been able to put my finger why, but there is something mesmerizing about videos of a hay train raking and rolling round bales ... That was an awesome sequence you posted. And thanks for all the info. Regarding def fluid, my NH had a defective def fluid sensor that the dealer replaced. It got progressively worse until the tractor wouldn't even start! Since then I never store def above 70 degrees, and I only buy def fluid that has been manufactured in the last 6 months. Blue def is the only brand I can find that publishes its manufacture date (albeit you have to decipher the code). I haven't had problems since.

If you haven't already had it done, ask your dealer to do the update to the a/c system. It is a major change in the way the air circulates. I believe they tested it in 2021 and was released shortly after. My neighbor had his 4710 done with the test kit and it seemed to help, but he ended up trading it before the hottest part of the summer. I have been running a TM1200 since 2019 and it has been a great machine. It has only needed two repairs. The needle fell off the pressure gauge last fall and the heim joints failed on the transport lift cylinder. I believe that to be directly related to carrying the mower in the up position a bit more than what was intended. The red transport bar is essential. Enjoy watching your videos. I'm not sure why I like to watch folks cut hay when I'm not cutting hay, but I do!

Really Nice video! Thanks for the tips and replacement procedures also website info. Really my biggest complaint with Vermeer is, not enough or absents of grease fittings! I’ve added many grease fittings to my Vermeer 604N, the VR 1222 rake, I need to add some on the TM 800 mower,around the main pivot pin. Happy Harvesting 😊

Nice baler setup! Never seen one with a rake. I also tested our tm1400 i have jd 6420 with 120hp no problem even in thick grass, i can drive 12-15km/h. Our fields are just way smaller than yours :D

That's a really nice setup, Chris.

There's a valve right under the cab at the front on the passenger side that cuts the hot water from circulating through the air conditioning if you didn't already know about it, it seems to help

I’ve had a few def quality warnings on mine also it’s only been with the peak brand blue def, I don’t buy it anymore.

Man I’ve been looking at the tm1200. To me that’s the sucky part is having to mow. I have a 9’ Kuhn and the tm1200 would almost cut my time in half. My Vermeer plugs every once in awhile. I replaced the pickup teeth and that helped but it will do it on long stem grass like Johnson grass because it tends hang on the hay saver wheels. I’m about ready to go to a wide pickup baler.

I have said it before but I'll say it again, It's always a treat to see a new video from you! I would have never have dreamed the 4710 would pull that cutter in economy PTO. Whats the reason for running it in EPTO? I would think that is just putting more load on the tractor and that's why the coolant temp is getting that hot? I have never seen mine get to the hash mark just to the left of the half way hash pulling a 12' bat wing. I feel between that cutter and then running the baler with the rake you need a bigger tractor possibly? Maybe a 6712 or 6713? I had a couple issues on my 4710 with the same DEF quality code and noticed it was only when I filled the tank up completely full, up into the filler neck full. I quit doing that and have't had that code come back in almost 2 years ago. I know after treatment systems inside and out and it doesn't make sense to me. Coincidence? Possibly but it might be worth a shot.

How do you keep things clean changing oil filter with it upside down. Is there a special way to remove. It's easy to access, only old oil in filter will pour out onto side of engine. Thanks for video and maintenance information l

Looking at one of these wanted to see how yours is doing any issues? Thanks

Looking at a 75 work master your thoughts? Thanks

What’s the total length from hitch to rear hookup??

Thanks for the info. Enjoyed it

Did you have a paint code for the yellow paint?

Did you re seal the motors on that r23a? Mines leaking and I’m wondering how hard it’s gonna be.

I know you don't have this tractor anymore but I've got the Case 75A equivalent. You said you swap the hoses for the attachment to float with the green handle/ports. This is my first tractor with dual rear ports. Do you think my Case green ports is like this? I'm only used to the single rear ports on tractors and now learning what I can do with this extra set of ports. Thanks.

The loader being higher allows the view along the front wheels to be much better though.

I just bought the same tractor two days ago...Thanks for the heads up.

Thank you. New Holland should pay you to explain how to use their equipment because they clearly don't themselves care about their customers. The information from New Holland is totally inadequate. Also there is no operators manual available on line, furthermore ALL service manuals and operator manuals should be available from the manufacturer online for FREE.

Thanks for sharing your your work. I have a 600 and by watching your video my winter project is to rebuild the cutting bar on my machine. The blades on the unit next to the drive unit are hitting literally trashed a new set of blades. The turtle on that unit has lots of play in it where it wasn’t torque down properly.

I've got a 4710 its a 2017 I've had def issues for the last 2 years I'm getting ready to head to the dealer about 100 mi away to have some codes cleared I don't know if I'm going to keep this tractor or not but they sure are a pain in the butt.

@CenTexAg I have been looking at this model for a while now. I know you have since traded your Workmaster in for a Massey Ferguson. Would you recommend the Workmaster or not?

Cris , a little tip for ya. That ep 0 grease your putting in those pofs is supose to come up to the bottom of the cross shaft, 3.4 oz. Heat that stuff up with hot water so it poors and you'll get a more acurate fill. Over fill causes heat.

Okay now i got the machine. My lifting system ball joint was shot. You can see it 2:30 under red lock bar. i can't believe there is not grease point there. There is huge stress to that joint. I would put at least some oil there "daily". Also both lift cylinder ends was welded, some one said here that these ends are aluminium, but in my machine those are cast iron. Other wise it was in good condition. I can see why they put those dually wheels, it jumps very easily with singles

Thanks! add also "tm1400" so more peoples will see this video. im going to pick up one tomorrow. We have smaller vermeer 40 serie mower it is 2004 and it has been very good machine. But will see how those bigger ones will last.

Why would the teeth rub on the spacers between turtles on start up and shut down I don't believe mine hit a working rpm no play in turtles new blades and pins

Great video, had the same problem on my 2012 T4.75. Saved a bunch of money not having to have service call. It acted wierd, would not shut off, but setting over nite would disingage, next day turn key on and off and would start. Did this for about 3 days, sure enough the cable had slipped out. The sleeve was rotated in a position that bolts were hard to get to. Thanks