Видео

Hello for sx 50 2024 it fit?

thanks!

Do theses have white letters on the other side of the tires?

Just bought the lights, thanks for the tips with the clips, no other video shows this.

Thanks for sharing they look amazing . How is the overall visibility now with and with out high beams on do they project down the road far ? Did you have to aim and align the beams ?

Ty brother. Great video! Can you update to show the glove box light replace. I for the life of me, do not know how :(

I didn’t use jacks or stands. Just my Mekon on 24” rims and level ground

I think you are supposed to have 10w40 gear oil and not engine oil.

Where does it go?

Where does it go?

Found a bulb on the floor of my 2010 Toyota Camry on the drivers side

Might want to replace that missing exhaust shield screw

You need to put grease on those clips buddy

Thank you!

The rod and bracket you pointed at is for the self leveling. Not the mag ride. The mag ride sensor is on the top of the strut.

Damn.. some1 got their money's worth out of those pads 🤯

Does this car have ABS? If so, did you need to mess with its sensors at all while doing this? Thanks.

anyone asking if this is done correctly, technically yes but do NOT CUT ANY WIRE THAT YOU DONT WANT TO STOP WORKING! for the lights on the trunk lid that only light up when the headlights (aka night time lights) DO NOT WIRE THEM TO YOUR BRAKE LIGHT WIRES. simply cut into your license plate light instead. wire them both to the same wire. They are the same voltage, its less work with fumbling with finding a place to hide the wires, and if you do a bad job then the only thing out is one of your license plate bulbs not the entire brake light!

Maybe stupid question but why engine oil with the gear box ?

You forgot the squealer devices on the pads. They also keep the pads from rattling. They need to be installed with them at the top of the pad so it keeps the pad forced in the direction of rotation. They were in the hardware kit. I saw them at 6:12 in your video. Also no grease on the rotor. You also should wire brush the face of the hub. A little grease on the tips of the pads. Not much though. You did a great job of showing the rest of the replacement.

You didn’t change seat hight or gas tank height? Bike can go lower.

Man those look really good, did they require any resistors??

How do you measure squash . I presume that what someone said above

olá da Itália, Florença, como esses pneus todo terreno Hankook dynapro at2 se comportam em asfalto molhado e na neve e lama porque eu estaria disposto a comprá-los para meu Suzuki Jimny 4x4! (Olá, tenho um conjunto de pneus todo terreno Hankook dynapro atf RF 10 205-70-15 m+s no meu Suzuki Jimny 4x4 e um conjunto de pneus recauchutados para terreno lamacento da marca italiana ziarelli e são do modelo mud Power ziarelli MT 205-70-15!)

Are these the v land headlights?

Czy występuje tam jakiś filtr który należy wymienić podczas wymiany oleju?

Jak często należy wymieniać ten olej?

Great video! Thanks

Thanks for the video 🤙

I just bought this exact bike, I have a couple questions, why do you have to change this oil if you mix oil with fuel when you run the bike since it is a 2 stroke? Thanks

Would say be the same 80 mm lowered?

Excellent brake replacement video. Thank You.

I just paid 17 dollars for my mechanic to do it. It’s cheap cus I live in Mexico

Thank you for shsring

Cant wait to take mine apart and see whats going on with my clutch. Jerks real bad when taking off sometimes, almost like its going on & off repeatedly for a second before going, and sometimes when clutch fully pulled while In gear it slowly moves forward. Just got the bike last year as a small project and going through lots of parts like this to make it perform and look like a new bike again.

Thank you for that great instruction video. I just revieced the Triple Grip Clutch - is it normal, that the clutch plates feel a bit loose? Seller told me thats ok and that i should just throw it in. It sounds clattering, as if the springs where not tightened enough.

Can you share the link for the wrench pls?

It's not super bad I just wish toyota made those rear ones more accessible. I really don't want to remove my windshield wipers and the motor and the brackets all those things...

Great for upper strength exercise. Just make sure your car jack works and don't go near sharp rocks. Might be ok for highways, and gravel, but do not take on sharp rocks. Bang for the buck is not a smart thing to do. And stop trying to act rich with your LUXURY statements. NO one really cares.

So cool! What are the two seat hights? 28" and 30"?

How’s the bike working out for you? I am new to the 2 stroke game, my son is 9 this July and two inches taller than yours. Thinking of picking this bike up for him and getting him a ton of seat time on it 🤘🤘🤘🤘. Thoughts?

God bless this gentleman for an excellent video

Amigo una consulta compré la misma moto pero le falta la bujía tendrá un fotito de la bujía para comprala porfa

Lil workshop tip. Never rub the locktite bottle directly on the bolt unless you want it to dry up inside the bottle. Locktite dries via a chemical reaction caused by being in the presence of metal and the absence of oxygen. Its pretty easy to pickup tiny bits of metal off the bolt them you put the cover on and it hardens. Iv seen this happen several times.

Perfect video! Way more simple than the other one I saw. This was straight forward. Just picked my son up a 2024 KTM65 SX yesterday!

Can u list the bulbs for the link

Do you have to bleed brakes after replacing rotors and pads?

Hey, heads up, mine is a year newer, a 2013 Toyota Camry V6 with the same engine all you have to do is take the wiper assembly off and the wiper motor and it gives you just enough room to get back to the back three spark plugs with the mirror and the right ratchet and extension to replace the last three spark plugs there is no need to take the manifold off or airbox or throttle body too much work. It is an easy job just to take the wiper assembly off and stick your hand back there with the mirror and you’ll be able to do it.

Hi. Will this work on a 2006 Toyota Tacoma v6 4.0 4x4. I have over 314k miles. Just cleaned the throttle body and I was real dirty. I seen a video where some guy disconnects the air intake manifold and spray in to the throttle body. But in my case my truck will not turn on. Also tried removing air intake manifold while truck running but turns off. I am definitely doing something wrong. Please help

Do u know where I can find the Direct Plug and Play Harness at in the 2012 Toyota Camry