2015 - 2020 GMC Yukon Denali 6.2L V8 Oil Change

2015 - 2020 GMC Yukon Denali 6.2L V8 Oil Change
How to change the oil in your 2015-2020 GMC Yukon Denali 6.2L V8 SUV.
How to change oil on 2015 2016 2017 2018 2019 2020 GMC Yukon Denali 6.2L V8, GMC, GMC YUKON, GMC YUKON DENALI, 6.2L gmc yukon v8 oil change, oil change denali, oil change yukon, how to do an oil change on gmc yukon denali, 2015 gmc yukon denali oil change, 2016 gmc yukon denali oil change, 2017 gmc yukon denali oil change, 2018 gmc yukon denali oil change, 2019 gmc yukon denali oil change, 2020 gmc yukon denali oil change, yukon denali oil change, gmc 6.2l oil change, yukon oil filter, 6.2l v8 oil change
2015 - 2020 GMC Yukon Denali 6.2L V8 Oil Change

[@BenjamIncredible]

Reset oil quick; press/hold the enter key on the steering wheel once at oil % screen. Use a 74mm wrench to remove and 3/4 turn past hand snug to install. Definitely lube the filter o-ring. Thanks for the video

[@MrJamieMan]

Thanks for the nice video. Wix is one of the best filters you can get bro! Always use rubber gloves used waste oil causes cancer. Also a good time to hit the outer tie rods and/or any replacement joints with a grease gun

[@nathanmasterson218]

Idk if I'd recommend using the oil filter tool you purchased to "tighten more than hand tight" You should only ever tighten the oil filter by hand until it makes contact, and then tighten 3/4 of a turn past that.
Great video and great instructions otherwise.

[@TheRealSkeptyk]

Good point.

[@tmill1967]

Informative, but always fill the new filter with fresh oil before installing it, that way the engine doesn't have to fill it first when you start it, and doesn't go without oil pressure that much longer.

[@chipsawdust5816]

Standard operating procedure. Also clean the contact surface on the engine where the filter mates up. And put a little of the old oil on the seal to lube it so it will move a bit once it makes contact. Hand tight, then another half turn if you can get that out of it.

[@silverbackgrizzly2402]

Very informative. Agree with the fill and clean area. Probably not that Big of a deal but once you learn away stick to it. Till you find a more efficient way.

[@Funkamedic]

Bro, you gotta prime these filters man, especially the VLOM engines

[@gnarlynorm7773]

I didn’t use jacks or stands. Just my Mekon on 24” rims and level ground

[@forrestdemaria]

Can’t believe you had a fram on that 6.2 lmfao

[@TheRealSkeptyk]

Filter is a filter my man, lol

[@chipsawdust5816]

@@TheRealSkeptyk I pretty much agree, unless you need a hi flow for high rpm engines etc etc. A filter is a filter, for 99% of stock road vehicles.

[@sublimefreak2244]

Wix is the bomb

[@mmerritt3479]

Great video thanks

[@TheRealSkeptyk]

Thank you

[@jimmysapien9961]

Thank you very much you forgot to say how long to warm it up before you drain it??

[@TheRealSkeptyk]

Honestly just 2-3 min

[@johnm5714]

How many quarts does the 6.2 liter engine take?

[@TheRealSkeptyk]

8 quarts.

[@johnm5714]

@@TheRealSkeptyk thanks-I just bought a 2018 Denali and wasn’t sure...sounds like it’s gonna be a pricey oil change

[@TheRealSkeptyk]

@@johnm5714 I buy costcos Kirkland brand at this point... 0W-20... The oil is half the price of Mobil... and I promise you it works just as good 👍, #savesomemoney my friend.

[@johnm5714]

@@TheRealSkeptyk that’s too funny-I was there on Sunday and saw it right next to the Mobil one...thanks for that heads up Pal👊🏻

[@chipsawdust5816]

@@TheRealSkeptyk Book says 8.42 with a filter.