Видео

Hello. What a job , as you say I think I’ll get it done by somebody who likes fiddly jobs. Thanks.

Music is so irritating, spoils the video.

The Cat is looking around and thinking “yeah, sure, what ever !”

Interesting approach to insulation.

You jinxed the van! 😂

Hiya mate, I know how you feel. I've had a break from my boxer camper install for the past 2 months but I'm now getting back on with things following a busy few months getting ready for the Isle Of Man TT I've got a question on your electrical hookup fuse board. I see it's got the power points on one circuit and lights and charger on another. I wanted to know what lights you've got on 240ac supply? I'm only asking as I was gonna just do the battery charger one one circuit and 240 sockets on another. Was it in your schematic? I'll have another look at that point in the video. Also love your paint job. Mines a silver 66 plate and has the dreaded paint peel in places so was thinking of wrapping or doing something else. All the best. Keep it going 👏🏻

I thought u were supposed to hold siphon a inch away from bottom

What's the name/size of the bulb mate?

Hey mate, thanks for the video. Would something like this be alright to sit on a wood stove full time? Cheers

Mint job man but you should be wearing a respirator that stuff is deadly 👍

I just had blackberries and racked into secondary and it's mushy and looking more like a smoothie should I. Use strain bags or just more hardy fruit next time ie stuff that won't mash up

Ok,how are you supposed to connect/disconnect battery if you are saying to reach in through drivers window to turn ignition on/off and not open any doors?? You have to be in the vehicle to do these things.

This video needed some beards. I'd like to see you grow a big Viking Beard. Don't be like me and wait until most of your red becomes white before accepting your natural gift as a man. 😉

Looks awesome. I’m doing similar to my LWB transit.

How was the mirror incompatible with the brake light/camera combo?

0hows the noise and air flow ?

Do you have a racking video for this particular cyser?

Fantastic job! I saw on the manufacturer's website they are made of acrylic. I would be concerned about the strength & hardness. The acrylic sold in USA by Home Depot is easy to work with, but scratches easily (melts if you try to cut w jigsaw). Maybe there are different grades of acrylic? I have used sheets of polycarbonate (very tough material) in a shed build, those cuts were made with a fine wood blade on jigsaw.

Hi planing to paint my citreon relay van with raptor,how much paint did you use please ,thanks aled

Could I ask what the red clip, where the Phillips screws are, is for. Mine is broken and don’t know if it’s vital.

I tried this Kiwi mead and didn’t understand fermentation at the time 😂 It turned out to be amazing.

That racks mental... if you dont mine me asking what did you pay for that?

Why would you use that honey in primary? That's a waste secondary back sweetening would have been a better idea and you wouldn't have used as much of it! You probably could have gotten twice as much using it to back sweeten with the same flavor.

!!! DO NOT USE ALL METAL TOOLS !!! like this guy - use insulated tools. Also: Whenever a vehicle battery has to be disconnected, switch off all equipment, interior lights etc, close the doors leaving the drivers window open. Switch off the ignition and remove the key and any diagnostic equipment. Wait a full 3 minutes before disconnecting the battery. The BSi must be allowed to go to SLEEP i.e. into "active economy mode". Do not operate any equipment on the vehicle during this time. Remember, even opening the bonnet will wake the BSi on a vehicle fitted with alarm. If the battery is under the bonnet, open the bonnet first and leave it up. ALWAYS disconnect any diagnostic equipment and do not operate any other vehicles during the 3 minute waiting period. PROCEDURE FOR BATTERY RECONNECTION Unless otherwise instructed by Peugeot or Product Service, you must always carry out the following procedure, often referred to as a "soft re-boot", to minimize the possibility of the BSi corrupting its own software when reconnecting the vehicles battery supply. Ensure the procedure for battery disconnection has been adhered to and importantly all BSi functions were switched off with the drivers window left down. 1 Close all doors 2 Remove ignition key if left in ignition 3 Reconnect battery. DO NOT open any doors 4 Wait 10 seconds 5 Switch on headlights through the driver’s window 6 Switch on ignition then start the vehicle and check system functions

Awesome video loved watching!

This is definitely a recipe for a berry mead vulcano! 😂

Thanks for the video! Looks like you might be a pembs boy like myself. Just about to raptor my crafter so this video was really useful. Just wondering how the paint is holding up since you applied it? Thanks

Thanks it was helpfull

Disaster 😂

Hi, your van looks really really beastly ! That price was for those 3 windows ?

I like to use a 5 gallon bucket for my primary fermenter. If you drill a hole near the bottom, you can add a tap to the bucket, and you won't need a siphon to rack it.

How is it now that it’s a year old?

Thank you showing all the steps!

Brilliant, this gave me the confidence to replace my dud battery

Why stabilize it? Isn’t it better to add more honey in primary and let the Yeast work itself out and go back into hibernation?

Thanks for the video, what size are the large windows please?

Hi, can you open this siphon parts? Mine can not open and clean , it seems permanently stick with glue -__-

Great vid... what colour was the reverse light wire on the van loom (that you fixed the blue wire to)? I want to tap into mine to fit rear spot lights - thanks

Very helpful, thank you!

Chefs kiss 🧑‍🍳

You need to get CubicMini wood burner in there! ;) Good work on the build. Im starting on my Iveco Daily XLWB as we speak, also raptoring.

Awesome I’m so excited my favorite drink now in mead form!! This will definitely be my first one I make. Thank you. Had to subscribed ❤

Thank you everyone for stopping by! A massive thank you to Martin for helping me out again! Also I would just like to correct myself in the video I said the hardener measuring cup was 250ml... when it's actually 236ml My mistake I hope you all enjoy -BD

Ew

Add some gelatin after the fermentation process to make your brew super clear and rid of any unwanted flavours and odours

im on the verge of starting to do my boxer swb, is their anything i need to know about removing the bulkhead, im not a diy buff lol

We love you mead man!!!

Try using a clear glass so we can see the final product

Great vid mate just what I was looking for although I have a Citroen Relay but cant imagine it will be much different, if you dont mind me asking, what spec battery did you install? Thanks 👍🏽

Great vid! How is the internal noise after fitting this, rain etc? Does it quieten the rear door clatter?! I've the same van (68 plate)that rattles and creaks like an old ship 🙄 Seems a good price with the discount.