Видео

👍

Hi, I keep it. Some people sell it.

@@aledhughes6000 Hi, the industrial fuse boxes are better, also high voltage switches. Even simple lamp switches. Elevator fuse boxes. Old telephone centrals. But mostly switches.

@@Wrightwayrecycling Hi, not sure exactly. Old Soviet Unit electronics.

Hi, correct! Mistakes are also good to exist, so other people don’t do them and have an example what goes wrong.

@@timothybourque7999 Hi, the issue with lead is that there is no easy and clean way to take gold from it. Probably the best way to separate gold from lead is to put the melt in a cement crucible and heat in an oven. There are videos on RUclips on it. Lead evaporates and a good bean is left. But lead fumes are toxic!!! So, it is done in controlled environment.

Hi, I checked the capacitors I have and unfortunately no such found. Apologies!

Hi, per the shipment documentation solution should contain cyanide, so I would not add acid. I usually add 2-4g NaOH to increase the pH to above 12 and then the zinc powder does the cementation.

@@escrapchannel Thanks for a quick response.

Hi, I have prepared material for more than 100 videos. Not sure when I will have time to restart, but for sure I will restart.

@@HardKnocksTime hi, 60g per litre of water is fine.

@@escrapchannel Not having much luck getting any silver thus far. I'm set at 1.8v my amps are low and won't go higher then .9. I've been going about 2 hours now with no silver peeling maybe just a tiny dust when I brush the item. Almost as if it's not working at all. Any suggestions?

@@HardKnocksTime you may have silver in the solution. Take 1ml and add table salt. There are two parts of the process: silver goes to the solution and some parts of the plating may fall too.

@@escrapchannel how much salt should I add to the one ml of solution,?

Couple of crystals - silver chloride should instantly appear as white residue.

It’s your choice and I respect it :)

Hi, fast reaction, dirty foam on top, etc. Electroplating and reverse electroplating are slow processes and the slower the better quality result.

@escrapchannel I had a very very dirty solution doing the 12v 6amp. I did use salt and distilled water. It was horrible. So much base metal in solution. I have non-iodized salt and distilled water here. I am going to try the voltage you have recommended. How long should I let it deplate before removing it and brushing?

@@HardKnocksTime wait, please! Salt? It will never work with salt in the solution. Thats the reason for the base metal quickly moving to solution. Please use Na2SO3 - 60g per litre distilled water. It will keep reaction smooth at the. Outage in the video.

@@HardKnocksTime Sodium Sulphite is the chemical name

@escrapchannel I will get the sodium sulphite and give it a try. I can't thank you enough. Give me a week and I will be back to let you know how it turned out. Thank you again for all of your knowledge, time, and sharing with me!!!

@@antoniokasabov9364 Здравей! Когато спре реакцията - отделянето на мехурчета или се е изразходвала азотната или се е разтворил метала от часовниковите каси. Изваждам ги, промивам и слагам отново в азотна. Ако реакцията рестартира бурно, значи има останал доста метал за разтваряне. Ако се появи съвсем слабо оцветяване, значи сме на финала.

@@escrapchannel Мерси за инфото! А накрая как успя с обикновена горелка да го разтопиш, четох в интернет, че трябвало 10-15мин да стоиш с горелката, за да достигне температурата на топене на златото.

@@antoniokasabov9364 Горелката не е обикновена :) Това е бижутерска горелка за малки количества и за ремонти на бижута. Мап газ и кислород - развива много над температурата на топене на златото.

Thanks!

Здравей, бройки има 😀 Опитвам се поне новите да запазя, но все ги тегли към лабораторията 🤣

@@escrapchannel 😁И аз имам едни, но си ги пазя

Hi, I use the body of a standard kitchen ventilation but motor is replaced with chemically resistant one.

Hi, auctions, eBay, …

Thanks!

Hi, big ones have 0.03-0.05g of gold each, so more or less the most valuable elements. But the bolts were cut in this case.

👍

I like gold! So, it is always an option :) THANKS!

Thanks!

1.5-2% from the MLCCs. That’s what I usually get. Sometimes more. Sometimes less.

Thanks! Agree!

Hi, I usually keep ceramic ICs. The older and rare - the better.

Agree! Too beautiful to destroy.

Thanks!

Thanks

Hi, yes. escrapchannel@abv.bg

Perfect!

Thank you!

@@escrapchannel how to get the palladium out of the capacitors please ??? You have a video? 🤔

Hi, I have no video yet, but I am planning to restart videos this year and palladium recovery will be covered. In general, it is more complex than good and silver and there are two or three main approaches. Not easy to explain in a comment.

Hi, haven’t seen such.

Hi, as the electrolyte is concentrated sulphuric acid it “favours” gold to be stripped while copper base or other metal stay mostly intact. Reaction depends a lot on the voltage, as higher current makes reaction faster but also impurities more. Gold product from the cell I refine chemically in all cases, so even if impurities present I clean gold during the refining.

@@escrapchannel great thanks I'll give it a try!

Please be super careful with the concentrated sulphuric acid.

Hi, thanks!

Hi, I tried but never recovered 0.2.

@@escrapchannel how much is from one then?

@@BigVik1111 If I correctly remember it was less than 0.1 … something like 0.08g. But it was long time ago so it is a good idea to repeat the experiment.

@@escrapchannel Thank you, i guess i won’t bother scrapping them then, better sell them to collectors

Hi, It’s time to restart the videos …

@escrapchannel yes please do, you and 999Dusan are the best

@@dannysearcy3373 Dusan is fantastic! Agree!

Hi, no. I do not sell scrap CPUs.

Hi, cathode can be different, but I find stainless steel as perfect. Not reacting, practically inert and easy to remove the coloidal gold when deposited on top.

Hi, for such amount reverse electroplating is too slow. Easiest way is to dissolve all wire in nitric acid, if you can find it cheap.

Hi, it is a little more than 2g 🤫

Hi, unfortunately I have no ceramic CPUs for sale.

Hi, no.

Мерси!

Hi, exactly! So everybody can decide if it is worth doing it. For countries where 10 dollars are enough to survive a month and for the countries where hourly payment is more than 10 dollars.

Hi, gold is my favourite from the noble metals :)

Hi, thank you for sharing your experience.

@@escrapchannelJust started using Eco about 2 to 3 months ago. I think the compound degrades over time. The first run I did was with about 30 lbs of pins. It took 1200 ml to strip all the pins and my recovery was close to 15 grams . More than a gram per 100 ml. Now it's just not doing it, no matter what I try I cant seem to get more than .85 per 100 ml.

@@joek511 Hi, I have an old batch bought more than 3 years ago, so if I find time I will test it. Thank you for the information.