Видео

Can the rack and pinion be replaced with out dropping the sub frame??? I really don’t want to do this right now 😅

Wish I saw this before I spent $1800 at a shop and they replaced my starter and both batteries first.

Use rubber gloves you savage .

? Cost off labor an how much hours for this job.

Thanks Bro! Your one of the good guys

Thank you for these videos, I used many of them and became very good at fixing my transit van saving thousands

Great video, thank you. Thanks for the part numbers, speaking clearly and very little camera shake. We are retiring our e250's and moving up to 2017~ transit 250 's. After research, seems like we'll be busy doing predictable repairs. Thanks again.

PART NUMBER FOR THE STAINLESS MANIFOLD?

Thank you. I saved tons of money by watching your videos.

What are you using for a bore scope ? The picture is amazing.

After having quite a few trucks in my 70 years of living I only had one ford and that broke me of ever having another, I’ve had several chevys and 4 dodges. I don’t know about fords but chevys dashes in the 70’ 80’ and 90 ones I had were the worse to replace and take apart, dodge 2 gens I know had cheap plastic and fell apart but lots of aftermarket pieces can be bought to fix back up and are easy as hell to work on. I have two now and one I completely went thru about 8 years ago and the other just this year both by myself.

My timing cover is leaking it used to just leakwhen tilted back on my drive way now i see it leak when parked on a flat surface. It looks bad on the drive way. It doesn't leak so bad as i have to add oil in 3000 miles its just about less than a 1/2 quart. I got a prce of $2300 to have it done at a independent for shop. My question is would it help at all if i re torqed the bolts where its leaking. The leaks on the upper left hand side.

Any update on after you changed this out? What happened, what ended up being the culprit?

You’re a great merchant everything done to spec. Thank You

My TC started to shudder, i just replaced 4qts of fluid today, gonna cycle it out and also added the lube guard to fix the shudder. The fluid was absolutely filthy at 84k miles,,,, bought it used. Hoping that changing the fluid will prevent this from happening for a while. That or ill trade in for a new one and be on top of the maintenance lol

He's right.

I am having same issue with my vehicle, even after replacing oil pump, timing and all the good stuff under front cover. Only comes on when oil is warm after 15 minutes, do you have a good diagram where this sensor is located? Also how long does it typically take to replace this sensor? Ford is telling me I need new engine 248K miles however I just replaced everything and seems to run fine, except for the oil light. Thanks for posting videos! Great way to spread knowledge!

Is this something that requires immediate fix? Or is it going to leave me stranded side of the freeway?

Spray some WD 40 in front of the pinch clamp onto the rubber hose.. The clamp will slide easily toward you now. 😀

If camper conversion with all that weight and going through the rockies and Mexico what should I get

Hi boss you are the best teacher I like the way you explaining the job I appreciate your help buscar precio wi-fi orfebre thank you very much

thank you so much....😊

I wish they dropped off like that here in NY. It's an entirely different experience. I replaced the hubs, rotors and hardware on a 2016 today. it took 5+ hits from a 4lb hammer to get the hub off of the knuckle. Great video!

Helpful was just working on our transit doing this

Thank you for posting this misty helpful.

New converters in calif are 5000 dollars

I have a T150 with the 3.7 and Quigley conversion. I run the transmission in 5th gear to prevent the constant shifting. The loss of mpg is negligible.

This video is for the 3.5 ecoboost.

Thank you very much, almost bought new battery, thought it was battery issue. Adjusted and it seems fine for now. Had issue with Auto sidestep causing engine to cut out

Will these part numbers work for a 2016 Trsnsit 350 high top?

Would you recommend I replace the bearing hubs as well while doing brakes? 95k on a 250

Clarifying an earlier comment: the 2018/2019 Ford Transit 150 SRW bolts are 50 ftlbs + 90'. The rest of the steps are the same.

what an idiotic design

After watching this video that was very informative I have completely decided against a install and spending the money on this product...I thought it would mount to a point of the frame of the vehicle... aluminum doesn't instill much confidence in a push bar ...I'll pass.thanks for the video my guy

I have a 99 Ford f250 super duty and have a new battery and alternator has been tested three times and the battery light is on went thru and check the grounds and there good and check the fuses and there good

what happen my ford transit t350 year 2006 black and no power

Great video.. been thinking of doing mine as my torque converter is starting to go, luckily ive made it 295k before any issues..

thanks, helped me through my first timing cover re seal

Thank you

Thank you

I believe this was a great informational video and you are very good at what you do you can tell you have done this multiple times I will now attempt to do my own. Wish me luck.

Great video very informative, thanks so much for sharing, do you have a video on how to replace egr valve on a transit 250.

Very well done. Thanks for posting and showing the right way to do it including torquing.

Anyone have the issue where the sliding door hits the fuel cover and pushes it off? Not the full hinge part, just the cover/flap. Every time I close the side sliding door it hits this flap/cover and knocks it off. I've taken it off fully for now, but this means anyone could open the fuel refill and put anything in my van. No idea how to solve this issue

appreciate this video, i work for a transportation company we have about 15-20 transit in fleet, doors are constantly an issue

What are you booking your chains to from the trailer?

Ford is replacing the Catalytic Converter on a work truck as part of warranty. They asked for the truck for 2 1/2 days to do the job. That seems like a lot of time. We are not paying but we don’t want it off the road for 2-3 days 🥸

What really gets me is i bet the sodding designers dont work on what they come up with and iv worked on alot of fords cars hgv,s and some of the stuff are completely stupid FORD START MAKING YOUR DESIGNERS WORK ON THE VEHICLES THEY DESIGN. AND THAT GOES FOR OTHER MANUFACTURERS AS WELL DERRRRRRRRRRRRR. thankfully im retired now 😅

Ford engineering is the worst

Thank you