Ford Transit Pinion seal replacement

Поделиться
HTML-код
  • Опубликовано: 18 окт 2024

Комментарии • 15

  • @AJourneyOfYourSoul
    @AJourneyOfYourSoul 2 года назад +3

    Thank you. Great tutorial. Your employer is lucky to have you. You take great care in your craft.

  • @mikefranks4528
    @mikefranks4528 Год назад +2

    I am doing a weekend marathon on your videos!

  • @fourwheelcamper5491
    @fourwheelcamper5491 2 года назад +2

    Thank you for step by step.

  • @lasallj03
    @lasallj03 2 года назад +1

    Good videos man I like how you cover everything

  • @nicholastaylor1546
    @nicholastaylor1546 2 года назад +1

    Thanks great as usual - just not often enough

  • @Da305Alive
    @Da305Alive 2 года назад

    Can you please make a video on a simple trans oil fluid level check.Everytime I do a service at a ford and go behind them and check, its overfilled and the trans is shifting crappy.I have to take some out because its way past the dipstick and spilling out.It says check running and in park.Before I can even take the yellow plunger out its spilling out everywhere.Am I wrong or what?

  • @lasallj03
    @lasallj03 2 года назад +1

    What state you guys in looks rust free

    • @medtec6747
      @medtec6747  2 года назад +1

      Oklahoma and yes we don't have much rust here. I'm incredibly grateful for that. I watch a lot of rust belt techs and they have my utmost respect.

  • @HachiKunRacingDevelopmemt
    @HachiKunRacingDevelopmemt 2 года назад

    Hey Mr. Med Tec, I've comented before and you've of great help and I was wondering if I could get a little bit more. My vans going to be up on stands for a little while as I Coyote swap it and I was wonderinf if you could give me a little insight on where I can place Jack Stands for long time use that will be safe. I'm dropping the front end so where you would normally jack it up on the front control arms won't work and I'm also dropping the rear axle, so that's also out of the question. Can I just put jack stands on the frame of the van or are there other places designed for the weight? Also If you have any other ideas that are safer than jack stands, I'd love to hear them!

    • @medtec6747
      @medtec6747  2 года назад +1

      There is a bix frame channel that runs the whole length of the van. I would place them on that channel right behind where your transmission crossmemeber mounts

    • @HachiKunRacingDevelopmemt
      @HachiKunRacingDevelopmemt 2 года назад

      @@medtec6747 awesome thank you! What do you recommend for the rear?

    • @medtec6747
      @medtec6747  2 года назад +1

      @@HachiKunRacingDevelopmemt the same box channel right on front of the leaf springs

  • @HikerBiker
    @HikerBiker 2 года назад +1

    Big, big, BIG NO, NO to use an impact on a puller. I think that's the first time I've seen you make a mistake ;-). We use to install a micro sleeve on the flange. Are those no longer made? We also use to use a small amount of gasket sealer around the outer part of the seal if the new one didn't come with it already installed.

    • @medtec6747
      @medtec6747  2 года назад

      Ya they still make speedi sleeves. The new pinion nut has gasket sealer on the back side and in the threads

  • @jessiecheema9411
    @jessiecheema9411 10 месяцев назад

    Where is your shope