Видео

By far the BEST video on the HT 101 Not only did I get it back together I also understand how all the components work together now! This thing is tricky and Lester simplifies it better than no other! Appreciate you Lester

Great video. Straight to the point. Thanks for sharing New subscriber here

Have their top battery machine, as of 2024, 540 iXP. Great power. Great in this regard. Chain tensioner mechanism drives me nuts. Essentially same as this. Keeps slipping, loosening, chain goes slack far too early after re-tension. Can see nub turn! No chain isn't stretching, yes am familiar with chain mounting fundamentals: lift bar nose up when tightening side cover - pointed the above out each time matter is discussed. Any solutions? Chalk brushed into tensioner thread perhaps?

Good job, thanks 👍🏻

Awesome thanks

My spline keeps separating, almost like the cover over the spline isn’t staying put. Any suggestions?

Very nice video. Bought one the other day. Muck in the valve . Easy fix with your vid. Thank you!

Would that somehow cause vibrations on my shaft. On my pas 225?

Very nice! Thank you!

Thank you for the advice 👍👍

This is my first comment ever. Lester, your combination of great video and great explanation is so helpful! You are a born teacher/trainer. Concise, accurate and documented with perfect video! Thank you so much!!!

Excellent video-a great help replacing bent outer black shaft housing-Thanks

I have a Stihl ht 56c want to upgrade from 10 inch bar and chain to the 12 inch bar and chain . It has the pico 1/4 sprocket what part number is the 3/8 speocket . And how many washers wil i need

I replaced mine and it doesn't change at all. It has a roll pin that only allows 1/4 turn. I removed the pin to try to close the flow and the whole adjuster comes loose. I tried 8 different amounts of turns and it still oils excessively.

Outstanding tutorial Lester. Thanks for posting and saving me so much time from having to figure it out what's inside these Stihl poles with no insight. cheers

Informative but bad camera angle

Will it work on a battery operated Ryobi?

Thank You!! I may try to use gloves again when working on small parts just because you seem to navigate well with them. Very clear instructions.

Awesome!! Thanks bro!

Thank you! This is exactly what we needed after trying to assemble the trimmer for 2 hours 😂

My Echo SRM 225 runs like a BEAST for about 15 minutes and then boggs right out... if I let it sit for about 20min I can repeat the process however it always seems to "choke" out. It'll restart immediately but the moment I hit anywhere near half throttle it starts to choke even though it ran perfectly normal up till then... lower mid-range seem to function but the moment you get anywhere near the high end of the throttle it just drowns once it's good and hot I've replaced the fuel delivery system, cleaned the carburetor, changed the spark plug and kept her topped off with fuel plus of course always kept a nice clean air filter... I build gas RC cars, ride Motor Cross Bikes and have Decades of experience maintaining chainsaws, lawn mowers and all types of gas powered equipment yet I've never seen anything quite like this... I guess the next thing I'm going to try is to completely swap out with a new carburetor? I bought her new and never had a problem for about 7 years of residential use🤔

С трудом нашёл это видео. Возникла проблема с заменой топливного фильтра бензокосы STIHL FS 90. Благодарность за подробное описание.

Was working at my shop and that tab broke off for the connector, I didn’t know what to do but this helped a lot. Thank you so much.

You saved my machine. I was about to buy new one. I really appreciate your time.

How do you get the primer bulb out?

You just saved me a trip to the shop and the fees that go with it. This pump failed once before several years ago. I lost a week while it was in the shop and I forget how much it cost. Thank you

Now a great straightforward no bullshit video great job.

Mr. Lester Olive In The Shop: Thank you very much for your video. It was certainly very useful, informative, and valuable to me cause following your advice I was able to fix my Stihl FS90R weed trimmer and now it runs like new again! Please keep your videos coming cause they save me lots of labor fees.

Much better, couldn't ask for a better video...thanks.

This was a great help to me. I realized through watching that I was also missing a gasket. Thank you.

Much better.....Thanks!

This might be the best filmed and best explained video I've seen on RUclips! Thank you so much for clearly explaining how and why your doing what you need to do.

$60😠😂😂😂😂😂😂

"Barrier bars"😂 😂😂 are a joke. That blade is garbage.

Terrific video very detailed but audio hard to hear you

You did an EXCELLENT job! I'll be looking for your videos for repairs of other pieces of equipment....Stihl brush cutter, etc! Thank you so much!

Can it be used without the blade?

Great video. I had the opposite happen. The connecting piece on my hedge trimmer attachment sticks out too much and won’t slide in. Any videos on how I can fix that?

Thank you sir! Got me out of a bind.

The bigger sprocket diameter will give you a higher chain speed, not so much torque. Think of putting your truck in 5 th gear and start up a hill vs 1 st gear which one will get you to the top fab steep hill?

NICE!!. Thats what i was looking for. I wanted to not use the million dollar grease but didnt know how to thoroughly get grease down, in there. Didn't think about tossing a zerk fitting in there. Stihl Head is Metric, 10x1.5 pitch threads.

Just paid $125 to get lightly used one fixed! Clean… just used it n LOVE IT 😅

Thank you fixed 445 in 10 minutes

great video, is the new Oiler an original part. thanks and God Bless.

How does the solenoid function on a generator that doesn't have a battery? Dewalt dg4300. Does it use power generated from pulling it over to retract the pin? Thanks

Where can I get these parts

If you are going to install a chain and adjust it at least lift up on the nose of the bar before tightening the bar mount nuts.

Thank you sir! You just saved me some money.

Nice video. To the point . Simple. Informative.

Stihl and Echo quit providing a port hole in which to grease the 10K rpm gear head. @#$!