Видео

I AM NOT SURE WHAT EXACTLY HAPPENED, BUT I WAS GRINDING HARD TOO BIG BROWN SUGAR AND I THINK I SNAPPED SOMETHING, BAM, IT JUST STOPPED, NOW THERE IS NOTHING...WILL NOT TURN ON OR MOAN OR GROWL OR ANYTHING....DO YOU HAVE AN IDEA AS TO WHAT MAY HAVE HAPPENED.....NO MORE LARGE HARD GRINDING....WHOOPS...

Thanks for going back and posting this video. $5 bag of fuses from Amazon and we're up and running.

Literally had my processor in the trash and dug it out. Fixed! Super stoked! Thanks for the video

Literally had my processor in the trash and dug it out. Fixed! Super stoked! Thanks for the video

I like it, I'll do mine in early spring. 😊😊

Nice 😷🤣🤡

Get a roll of solder wick to clean up the pcb holes. Spring loaded solder suckers work well too.

All things follow the laws of physics so an old chain is longer. 🖖

How is everything holding up? Will an oregon bar fit this saw? Thanks

Why don’t people show where to connect the the compressor hose. Key element in this project.

Leave it to a "modern" manufacturing company to utilize an essentially non-serviceable fuse so the average consumer has to throw the whole thing out. I absolutely revile that way of thinking and doing "business" (I consider it more extortion of the consumer).

Ahhhh you switched jib line

May i ask what the cabin winches are for?

If the holes were not tapped in the kawasaki then how was it mounted in its previous frame ? I'm thinking of a swap as well between a kawa or gcv190.

Hello, Does it have a signall strength metre?

How did the restoration project go? I am looking at one of these myself at the moment.

Musi too distracting and connections kit not shown

Is that a dilly trailer

My 88 S10 is pretty peppy with its Iron Duke & 5-Speed manual.

So four years ago…. This engine was $204 or whatever on eBay. They are now $430+ dollars. Hahaha…. Gee HOW DID THAT HAPPEN?

That doesn’t look like the Kawasaki FJ motors I’ve seen. But damn $200 is a deal, it’s 2024 now and now that engine is almost $500 😮

Grab a can of silicone spray and they’ll slide in without removing the coils. Still a pita, but saves time.

Wow thank you so much! This was my exact problem! I would have never been able to figure that out on my own. Just curious if anyone else experienced this but I’m wondering if my food processor is spinning slower after this fix. It’s hard to remember what it was like before and I don’t have another one to compare it to… wondering if a bad soldering job can do that.

Just an FYI. That nuts torque spec is 70Nm + 180 degree turn.

Good time to clean the engine, cooling fins, and oil cooler off with an air hose, too

The bauer and Hercules tools from hf are pretty nice for the price point

Do you have an updated review?

First time novice solderer here and I fixed my food processor thanks to this tutorial!!!!

I replaced with same fuse and it kept blowing. So I put a 5amp 250v glass fuse and it's worked for about a year now

Honestly not that bad! Its a light weight car. I drove a mint factory fresh 84 Fiero 4-Speed and found it quite peppy and very enjoyable to drive!

Awesome! I fixed my mixer as well, thanks to you. I live in Sweden and use 230v, and the fuse did not look exactly like yours. I bought the same fuse you did, and it worked just fine. Thanks!

Why would you do this? Haven’t you just created a pocket to HOLD water and damage the wood and rope

Excellent video. And excellent choice in music the first one sounded like Van Halen. Who is it? Did you by chance look a harness that would connect through the factory plugs behind each light? It’s basically like adding a TEE. Keep up the vids

If you want to use these for 2 or more years you need to go with the higher grade covers. ShelterLogic makes 15.5 oz. (per sq. yd.) and 21.5 oz. (per sq. yd.) replacement covers. They are expensive but are guaranteed for 10 and 15 yrs., respectively.

SUb .. NICE I’ve been wanting to get one of these for my front yard .. two summer ago we had that crazy heat wave with no rain and it cooked my lawn to a crisp lol would of been nice to have a these .. I plan to run this off my well sense I no longer use it , I am on town water now .. Seen a few of your videos and Noticed the state your in and just laughed lol I my self live in the area lol small RUclips world .. I’m South Cost

Where exactly do I attached the compressor hose on the Orbit system? After I blow out the system do I just shut off the water or do I shut off the timer or programming box?

My engine went out and I replaced it with the kohler cv224 command pro engine

Thank you, your video was the fix. It was a blown fuse and I followed your video to make the fix. Fantastic job!

Big thanks from Australia - the fuse cost $25AUD to post here but well worth it as mixer is back up and running and another one saved from landfill. Happy wife for xmas cooking prep too!! Great vid mate.

Changed the fuse now I get power at least. But it’s blinking and motor not working. I saw another post about a possible in-line motor fuse. May open back up and see

Thank you for this! I'm wondering though, is there any way to put in a resettable fuse for the future so that if it blows, I won't have to go through the soldering steps again? I know nothing about fuses or their specs, so I wouldn't know how to choose an appropriate one.

Dude, thank God for people like you. Thank you so much for taking the time record and post and even put links up. Very much appreciate it Exactly what was wrong with mine

I like the duke not fast but can be peppy with a roller camshaft and bit of a different intake for s10 lil 2bbl yea realize it’s not a power house but behind a manual transmission in a fiero u can have fun with that 90 horsepower lol 😂 I believe they are better than some of the fuel injected turds well not faster but stronger and easier to get parts for anyway

The attachment part was the key. Everybody knows to blow it out.

exactly what i was looking for, thanks this helped me

I put together a 12 by 20 shed. The material was excellent. The instructions were clear. The only problem I had was sliding the pieces together. I had to grind down the burrs that were on the pieces. More than 80% of the frame had to have the burrs ground down .

Does Amazon still have that window

Oh my gosh, I actually did it! Thank you for your very thorough and explanatory video. I have never used solder before I didn't even know what it was really. I bought my food processor a few years ago and used. It may be five times and it went dead and now it's working again yay. 🎉

Thanks for the video, very helpful. Do you know if the 32" measurement includes the nailing fin or does the actual window without the fin measure 32x14?

I may have made the worst solder in all of history, but this video was awesome and somehow my food processor works now!