Видео

Where do you find sheets of the coroplast?

What truck do you use to pull the 240BH? Will a 1/2 ton pull it safely? Thanks

Thank you thank you. I’m about to make a big change towards my future and was researching living full time in camper. I was mostly concerned with insulating camper to make that a feasible option. I know I can gut the interior at some point and beef that up but knowing what you can to the underbelly has given me a piece of the puzzle I didn’t have. You’re a Godsend!

Great job! I seen the back of the Pontiac and the top of what looked like a 60s chevy ? Nice.

Great job tucking around the propane lines. Thanks for sharing.

Great video! Thanks for sharing.

Thank you so much for making and posting this video on YT . It is very informative and helpful, and you have such a beautiful family! Treasure your time with your kids while they are still participating 👍

Thanks bud

Is it needed in FL

Just a thought won't your last piece come in before it freezes? If so this last piece might be a waste of time and effort.

Isn't the two little drains are your what they call low spot drain to drain water before you put antifreeze in your lines also to flush out the antifreeze? Your hot water pressure release come out from the hot water tank its self.

Sewer stays around 60° you might want to keep it open to the rest of the underbelly because it will help keep the whole underbelly warmish.

my family used to own that park

Q What was the Size of your Frame depths floor to bottom

Gonna steal ur idea… I like it!!!

You can actually take a razor blader a sharp knife in trim back that expandable foam so that it's flat. Then you can paint it after your trim it all out of there.

Hi Texan. Really appreciate your efforts here I learned a lot. You used self drilling roof screws. My Zinger has 1/8 inch or so steel frame. I cannot even drill into it. What sort of structure are you drilling into? Dave.

I used to swim noodles around all my wiring and my propane hoses how do you think that will work I'm also the one who put the foil side of foam wrong I hadn't watched any videos there's something I wanted to do now wishing I had watched your videos

I did this job myself last weekend and now I'm seeing your video and I see that I put my foil side wrong will it cause a problem

Better test that adhesive first. Some of it eats the foam insulation. Really like melts it.

Great video ! THANK YOU

Man I’d love to know the motor / mount etc you bought. I have a similar situation. Great video!

Great job with this video. I really appreciate the time that you took to document and video the project. Very helpful for those of us who are looking to install underbellies on our RVs. You are creating great memories for your kids that will last forever. God Bless you.

What did you use for straps

Wonderful, wonderful, wonderful!! THANKS! Just what I'm going to have to do soon. Thanks for taking the time to video all the work and the little tips on your experience doing the project.

Dead channel lol 💀

I need to access my under belly... There are rivets screwed into frame... Can I take them off and then put them back on???

If you use flash tape it will keep the insulation in there without screws too and it is cheap

Very good video, it helped me a lot. God bless you. Thank you.

very helpful video's. thank you

Great idea with the expander foam but once dry it can be cut with a long blade knife or a fine tooth saw then I’d spray it black as you did. But at the moment it looks so ugly & an unprofessional finish even though it is just doing that simple neaten up will looks so good 👍🏼

Nice job !

Has anyone completely removed the existing membrane on the bottom of their campers and just using this plastic sheets as the bottom floor barrier? The membrane on mine has holes and frankly stinks bad. I want to cut it completely out

Would it be more efficient to put down some rubber or foam backed floor covering for the Winterseason ?

Thanks for all of the info! Very helpful 👍

You did a great job. I have a question for you. Can you please install mine? Thanks for the video.

I watched these two videos a while ago. I am going to try to do this on my fifth wheel soon so I am watching them again to prepare.

I used a little square of the underbelly material under my fender washer so the washer wasn’t crushing directly on the actual underbelly….I would trim the foam , maybe an inch or so away from the underbelly… leaving enough to lock it in , but not having all the extra that’s doing nothing but possibly catching dirt.. I would paint mine like yours… I’m also caulking all my edges so no water makes it’s way into the channels of the underbelly..

that was a lot of work, and it seems to have turned out well

Great video!

I’m fixn to live in a 30ft. Vintage Camper trailer & im looking for ways to get it insulated & to keep warm.seriously though,I Nvr thought of the underbelly,I’m sooo glad I came across your video.Im also looking at heating flooring,solar panels & a efficiency electric box.My son is a wood worker & he’s coming to put hidden spice racks & etc... into it..Can’t wait to see more ideas from you.Thank you

Thanks for sharing this video...even if you had some techy issues...still looks great. Stuart and Missy with 3 Dogs and an RV

Thank you for the video It's helping us insulate our fifth wheel. last night it got below 28 burrr. It makes a big difference.

Great video my question to you is if you have a water leak then you have to take that all apart

That makes sence! I had the same foam without and the r value was less 1. Somthing! Anyway (unrelated) the foil would legitamtily add a higher r value! Seems acurate as long as the foil was on the inside of the room to bounce the heat particals around!

where ya spray foam fam?

Thanks for listing the supplies!

sip your beer EVERY time he says "alright so now .. " .. you'll NEVER finish the video HICCUP!!!

Would this increase the chances of condensation and water damage?

Another great video and job.