Thank you very much! Very helpful video. Both my rear signals/ brake lights inop. After some diagnosing I believe it’s the BCM. Owner hooked up jumper cables backwards and caused a mess!
I walked out to My 2012 F250 & hasn't drove it in a day. The Brake light was on shining. Finally got it to go off. Couple days later was pulled over because of sparks coming from Underneath & the Brakes felt Strange! I had to use my left foot to pull brake back up if I pressed on it , cause wasn't stopping right. Was CRAZY! Had to have it towed in. Then approximately 30 days later DEATH WOBBLE happened! ONLY had 104,000 miles on it.. WORST FORD & ONLY F250 EVER PURCHASED!! NEVER WILL PURCHASE F250 AGAIN! Around $8,000 work in 30 days. ONLY SERVICED at DEALERSHIP! SURPRISED THEY DIDN'T SEE IT!!
quick question boss in the video towards the end when your programming the truck are you programming the new bcm to the truck or are you just programming 2 new sets of keys to the bcm any help is appreciated I seen that before you programmed it the rear left turn signal was flickering fast but after you did programmed is was blinking normally
Where are you located at? How much was to repair this truck i have same one but just passenger side light wont work. I bought truck from guy in MS and I believe it has the same company logo as the one in your video
Thanks for the video. I am having the same issue on a 2012 f150. I saw another video and they said you could reset the bcm through the obd connection, is that correct?
@whiteoneauto Update I hooked an ELM 237 diagnostic code reader up it showed BCM errors, I reset them, and the turn signal now works. Thanks for your content.
@@whiteoneauto i use the same relay tester as you did and at 9:36 in the video you use the jumper and close the switch and you get power at pin 1 instead of pin 3 wheni do this i dont get power to pin 1 please help lol 2 bcms have been put in
Thank you very much! Very helpful video. Both my rear signals/ brake lights inop. After some diagnosing I believe it’s the BCM. Owner hooked up jumper cables backwards and caused a mess!
Thanks for watching.
Did you get this fixed? I have the exact same thing happening. Didn't jump it or anything though.
@@dbearden3232 It was the BCM
@@Firecat1976 did you have to replace it?
@dbearden3232 The fix is in the video. Please watch.
I walked out to My 2012 F250 & hasn't drove it in a day. The Brake light was on shining. Finally got it to go off. Couple days later was pulled over because of sparks coming from Underneath & the Brakes felt Strange! I had to use my left foot to pull brake back up if I pressed on it , cause wasn't stopping right. Was CRAZY! Had to have it towed in. Then approximately 30 days later DEATH WOBBLE happened! ONLY had 104,000 miles on it.. WORST FORD & ONLY F250 EVER PURCHASED!! NEVER WILL PURCHASE F250 AGAIN! Around $8,000 work in 30 days. ONLY SERVICED at DEALERSHIP! SURPRISED THEY DIDN'T SEE IT!!
Sick video! Thank you so much
What program do you use to find wiring diagrams?
Snap-On ShopKey
@@whiteoneauto awesome thank you! This was the exact video I was looking for, really appreciate you making it
quick question boss in the video towards the end when your programming the truck are you programming the new bcm to the truck or are you just programming 2 new sets of keys to the bcm any help is appreciated I seen that before you programmed it the rear left turn signal was flickering fast but after you did programmed is was blinking normally
NEW BCM FOR THIS TRUCK. THANKS FOR WATCHING.
At 9:36 in the video I do this same step and power stays on pin 3 doesn’t go to pin one what does this mean
Is it that hard to just say what this means dude like come on
What hardware are you using to connect your computer to the truck?
SnapOn Pass Thru Pro 3
Where are you located at?
How much was to repair this truck i have same one but just passenger side light wont work. I bought truck from guy in MS and I believe it has the same company logo as the one in your video
My other side is doing the same is that were the harness is at on the passenger side
Both left and right sides get a signal from the BCM to turn on relay for turn signals. Thanks for watching.
Thanks for the video. I am having the same issue on a 2012 f150. I saw another video and they said you could reset the bcm through the obd connection, is that correct?
Thanks for watching. Not sure about someone else's video, but this truck needed a BCM.
@whiteoneauto Update I hooked an ELM 237 diagnostic code reader up it showed BCM errors, I reset them, and the turn signal now works. Thanks for your content.
Do you respond or just like the comment your no help
I don't think I use fuse jumper. I used a relay tester.
@@whiteoneauto i use the same relay tester as you did and at 9:36 in the video you use the jumper and close the switch and you get power at pin 1 instead of pin 3 wheni do this i dont get power to pin 1 please help lol 2 bcms have been put in
What would this mean