Agreed, I have their offset red dot mount and it's well made, and super low profile, enough to fit easily under the front of my scope with out any fiddling about. It mounts rock solid and held it's position over 500 rounds with no shift in position.
I stopped using Aero Ultralights after I got two in a row with out of spec clamshells. They would rotate the scope body as you tightened the screws, and the tighter they got the harder it would be to counter the rotation without slipping completely out of place and simultaneously staying level. Took twenty minutes of fussing and adjusting and readjusting just to get one set correctly. Every time I thought I was finally level I would put the final torque on the screws and find the scope had shifted two or three degrees. I gave up once I realized the second one was the same way. Never looked back.
Great mount I used for years with an AR15 and it handled most of the abuse with no issue. I've since upgraded that setup with a Weaver. Thanks for a great review for the everyday Man. "Stay Strong, Chase Excellence Brothers."
I've been wanting you to do a video like this for a while. You do scope test, I want to see how you mount scopes and what equipment you're using to make sure that you're adjustments are consistent. This is a good start.
I am really glad to hear your positive oponion on this mount. I bought it recently because I didn't want to spend hundreds of dollars on a mount. I just couldn't believe it has to be such expensive to work fine.
The two smaller blocks are actual securing the drilled blocks as the contact points on the rail or contiguous. and solid.. I am going to get one.. I like the Spuhr mounts...But this will be a nice comparison to see.. I like that this has all the screws being flush.. Thanks for sharing..
Been watching the channel sporadically for the past year and it has become a valued info source. Sub'd today. I couldn’t find a vid on your scope leveling / mounting method you touched on here; that'd be cool coming from you.
I have a couple of these offset mounts, as well as a couple of sets of their US made scope rings. Zero issues. Even have much older imported UTG rings on my 10/22 for over 10 years. Made Rifleman with them in 2011, and shot it a few months ago. Still zeroed. Even like the Accu-Sync sights, and have a set on one AR, and recommend them to all my beginner friends for their new builds. Never had a complaint.
These are really great. Lighter than a Warne X-Skel, stronger than an Aero ultralight(those break if you look at them angrily, I've broken 2 with no rough handling.) cheaper than anything else worth your money. And unlike the Aero it can handle abuse. The QD one is about $70 and is every bit as good the non-QD. I have a few of these and a pair of qd and I love all of them, though the QD are the only ones that are in use.
Oh hey, I currently have one of these holding my RT-6 onto my AR. My only concern with it is the steel base screws into the aluminium threads, but the torque specs are well within what should be fine, and I haven't stripped any or had them come loose in the couple of times I've removed and re-attached the mount.
The majority of mounts are steel into aluminum. Its only when you get into more expensive mounts that are either made of 7075, or have stainless threadserts in that you dont have to worry at all about it.
I got an improperly machined one. Hit it with a file to remove the massive machining booger but it was almost bottoming out in elevation still. Gave it to a friend in need and let him know. Spend a little more and get a Warne.
I just bought this I've bought their stocks , grips , handguards , scope rings.... I have yet to be disappointed. The ar10 super slim free float.. I wouldn't trade it for a Seekins or MI. As for made in China I think their made in Michigan and have been since 2012.
@CDOES I second that request. My concern is the lack of full tang for the picitany rail. Then, the fact that it does not have steel insert in the threaded area.
Bought a New-Old-Stock Gen 1 UTG Recon 360 Bipod, only design flaw is that it needed longer/tighter Allen M2 tension screws on the ball joint. Now it holds better on adjustment. Has full cant and tilt for a bipod, $60 for $200-300 functionality.
I'm glad you did a video on this. I've used these mounts and would recommend them but everyone would laugh at me because it's UTG. UTG does have some sleepers. Their receiver extensions, offset rds mounts and these scope mounts have all worked great for me. I still run some of their products and this is coming from a guy who's into ADM, Badger, Scalarworks and Geissele mounts.
I have lots of high end scope mounts and several of these UTG mounts...the UTG's are every bit as good at less then half the cost. Monstrum also has some really good mounts available for a reasonable cost; especially their 7075 Pro Series and Razorclaw series. With today's CNC machining tech, there is no need to spend $300-500 for a great scope mount.
I more or less accidentally bought this one. I went to pick up my 3000€ AR, already bringing my 800€ ish Hawke Frontier thinking I could also pick a mount. Well, got a heart attack when I saw the prices. So I cringed really hard and bought the 80€ mount 😂 Honestly, I did a good job so far. I’ll still replace it when I’ll move the scope to a .308 DMR.
I have a UTG I used for my vortex Strike Eagle. Budget optic with a budget mount. Zero issues. Don’t need to spend all kinds of money for a good optic/mount set up.
@@jguerrero0311 I like it. Once I figured out how to get it tight. Don’t necessarily like that design as far as the way it fastens on but once I got it on and tight I haven’t touched it since.
Hi C, I never wondered about this and there's a good chance you mentioned it at some point already, but are you from Boston or somewhere around? For context, I'm a foreigner, have very little knowledge of US accents, but the "cost effective" at 2:10 certainly made me perk up :D
Ive always wondered, do more pic rail lugs really do anything? Unless your rail and the mount are precision machine matched, id doubt youd get more than one lug engaged at a time.
Any chance the QD version review is coming soon? I’m thinking of either this one or the aero LW for the primary arms 1-6 nova 🤔 Thanks for your amazing reviews!
@@jguerrero0311 hey. I actually returned the nova. Was a great scope but decided on the PLxC in peanut butter color as it went with my theme. The mount I’m using is the badger ordinance 30mm 1.7” they don’t perfectly match in color but they look really good together. I had the utg qd mount for a bit but decided i didn’t like the look. I think it’s good for the money tho.
I run these and the non QD "pepr" mounts and they get quite abused and have no complaints. I get a good bit of hate when i run optics like my 1-8 credo in them lol. I've dented my credo on a one of many concrete drops and still held zero. I also quite like the bubble level top cap you can get on them. haven't messed with their offset dot mount as it's not my thing.
I’ve used these a Few Times they’re great. I also Have use the “pro” rings on a few setups. They’re excellent for what they are. Very good quality. But they have odd part numbers to figure out what to get with the offset and all that overalll though excellent
Got one of these when I bought a used Stryker hd 1-6. Pleasantly surprised with it, ended up replacing it with a larue for the rifle I put it on but it will be great on a 10/22
I have a bunch of these, one in particular (high profile 30mm with 50mm offset) i had a utg 4-16 scope in it on an ar, that scope is ok, not the best by any means but it tracks decent and holds zero, but anyway i had the rifle slung across my back, and i slipped on ice walking down the driveway. Fell straight onto the front top of the scope. The scope did end up bending but not enough to notice until shooting it, that scope may still be ok but i replaced it and reused the same mount. Mount is completely fine and this is my personal #1 recommendation for an ar scope mount. These things are solid and you can sometimes even find em for about 25 bucks new, the most ive paid for one is 35 and i have like 6 or 7 of em. Never had any issues with zero using these mounts. I want to try out their qd version as well. Also their little 50 dollar rheostat red dot is surprisingly good, it holds zero and doesnt blink like the vortex strikefire 2, the utg pistol red dot however does have that flash, the screws came loose (the factory installed top ones) and it had water spots for like a month after submerging it. It does however still work just fine, the water spots are now gone, and it has held zero since tightening those but i cant recommend that one. Overall their optics and mounts are solid with a few outliers, also i love my utg t1 riser and it looks cool to boot. Also theyre like 20 bucks and are solid. Edit: spelling
It would be really cool for you to get the monstrum pro mount on the channel. It's 7075 and if I was a betting man the monstrum and utg are manufactured by the same people (at least the chinesium utg stuff).
Trying it for a while, seems pretty solid for a cheap mount. Just wish it came in different height options without having to use a riser so I can clear my tape switches and the thumb on top of it
Do you know anything about Precision Reflex Industries' 30mm cantilever mounts? Any recommendations on a budget friendly 30mm mount that has a rmr mount at the 12 o clock position?
I just yesterday put the one inch tube version on my Tavor 7 and shot 200 plus rounds of .308 with no slipping or accuracy issues. This thing is awesome and fairly lightweight!
I have an aero precision mount. It corroded where the screws go at the clamping point to the mount and I basically had to break it off. I usually just stick to the Burris mounts even though they are heavy. Would love to see the follow up to this mount. As always, thank you for your videos. You are a must view before purchasing optics.
man, really makes me kind of regret spending 300 bucks on badger ordinance mount. I run the acro topside. However, it's stupid high. I've been desperately looking for a mount to replace it and lower the acro a bit. Do you know of any top plates that could replace one of the top rings
Another good budget mount is the Hiram. It was around before PA released their $220 version. It’s $30 with 3 bolts and 2 recoil lugs. I’m wondering if PA’s RMR ring topper will match the mount though.
I wonder if UTG makes a "Red Dot RDS" piggyback top ring for this. Main reason I'm a fan of these is no knuckle-hazard. Most economical mounts will rip your fingers on special/non-AR platforms.
Thanks Brother. Another nice review of something I’ve been eyeing lately. I just finished a dedicated .22lr upper and I think this would be a perfect mount for it. I only see one issue but it’s irrelevant for my above use. UTG make a piggyback RMR ring cap for this it’s really tall. Theirs is high enough for an MPVO with a large elevation turret but way too high for most LPVO turrets. But yeah, this looks like a great option for a budget, .22, or beginner gun. UTG gets some hate but I’ve never had a bad experience with the few things I’ve had from them.
Thanks, and if you think the optika6 is nice you should look through an R1 or ZD model, I have two R1s one ZD, and 6 optika6 scopes and one optika5, my favorite brand, I do own Steiner and Leupold too. Love the videos!
Oh a 2-12 ffp would be interesting and nice an AR or hunting rifle or one of my 10/22s, I am surprised they didn't reply. They replied to an email from me in a matter of hours, but that was for Scope turret covers I left in the woods they did send new ones at no cost though.
I have a bunch of these! The only reason not to use them is if you want to save a couple ounces then go with the Aero Precision lightweight. It's twice the cost and not as strong however!
I have been waiting for over a year to see this review. Looks like there is a lot of bang for the buck. I have two of their smaller risers that use thumb screws and I have been impressed with the manufacturing quality. With that said, they over spec their torque settings. I have the UTG OVER BORE BIPOD and the Torx screws stripped when I attempted to remove the bipod.
I have a cheap UTG QD mount that feels loose.... but off and on, and the dang thing holds a decent zero. Never more than an inch up or down, and half the time, perfect zero.... 🤔 It has no right being that good.
I bought a UTG QD endplate and it has a weird slant on it that makes me not want to stake it, so I just ugga dugga'd it a bit, but thought that was weird This thing will save me almost 2oz over my cantilever sport mount though, so ill probably check it out. I'm just using it at a range
The known failure points of the Aero mount are why I decided against it at the last second in favor of a Leupold Mark AR mount instead (plus the Leupold was cheaper.) This UTG mount does look like another decent alternative to consider in the future.
Expensive mounts for ARs is super stupid That one is spot on. I have expensive mounts. Really is a bunch of bs. Guy good stuff for bolt action. Daum upper is aluminum anyways. Not going to be but so strong to start with. 😂😂😂😂
I own several UTG picatinny risers for red dot optics. Top top quality. The next step up in performance would be Scalarworks. But at 5x times the price!
@@FederalPacificEh there are certain brands that have a bad stigma in the gun community and no matter how good their new offerings are, they will never break into the enthusiast circle. UTG is one of those brands.
@@FederalPacificEhfor about 10 years UTG was potmetal chinese crap until they started their made in usa “pro” line. It’s going to take a long time to shake that bad rep.
I guess I can come out of the closet now. I have 3 of these: two 30mm and one 34mm. Bought the first one out of curiosity and couldn’t find anything wrong with it, so..
I love that utg/leapers stuff is cheap, fits together well, at least mine does, their lower third t2. I use it with a holosun 503r gold, and I also like supporting American manufacturing.
Took you long enough to review these. Between their "medium" and "low" and a half inch riser, you can experiment with multiple scope heights for less than 200 dollars, like 1.79 height. Meanwhile people were paying up to 300 dollars for a single 1.70 badger mount. Wish they still sold their fde versions.
UTG leapers has a couple products that truly punch way above their price point. I've used one of these mounts for years. Zero problems.
I love their dovetail rings that are on my CZ457. This is no exception.
@@CDOES6061 or 7075? Website says “aircraft grade”
Agreed, I have their offset red dot mount and it's well made, and super low profile, enough to fit easily under the front of my scope with out any fiddling about. It mounts rock solid and held it's position over 500 rounds with no shift in position.
Agreed
SigM400s came with utg rails for a while. They were actually really nice, solid and looked fantastic. They convinced me then.
Your reviews are far the best ever!
Ok, now we need the torture test.
Thank you for reviewing these!!
Im going to come up with some game plan for this.
I stopped using Aero Ultralights after I got two in a row with out of spec clamshells. They would rotate the scope body as you tightened the screws, and the tighter they got the harder it would be to counter the rotation without slipping completely out of place and simultaneously staying level. Took twenty minutes of fussing and adjusting and readjusting just to get one set correctly. Every time I thought I was finally level I would put the final torque on the screws and find the scope had shifted two or three degrees. I gave up once I realized the second one was the same way. Never looked back.
Great mount I used for years with an AR15 and it handled most of the abuse with no issue. I've since upgraded that setup with a Weaver.
Thanks for a great review for the everyday Man.
"Stay Strong, Chase Excellence Brothers."
I've been wanting you to do a video like this for a while. You do scope test, I want to see how you mount scopes and what equipment you're using to make sure that you're adjustments are consistent. This is a good start.
I am really glad to hear your positive oponion on this mount. I bought it recently because I didn't want to spend hundreds of dollars on a mount. I just couldn't believe it has to be such expensive to work fine.
I like finding things that are good and aren't a fortune
@@CDOES you may wanna try something from Vector Optics then. They make some decent scopes and prisms.
Every once and a while UTG kills the game
Lol.
The two smaller blocks are actual securing the drilled blocks as the contact points on the rail or contiguous. and solid.. I am going to get one.. I like the Spuhr mounts...But this will be a nice comparison to see.. I like that this has all the screws being flush.. Thanks for sharing..
I recommend lapping the rings before putting your scope in..
Been watching the channel sporadically for the past year and it has become a valued info source. Sub'd today. I couldn’t find a vid on your scope leveling / mounting method you touched on here; that'd be cool coming from you.
Nevermind, I found it: ruclips.net/video/B475m1skueQ/видео.htmlsi=YHw8Y2AiKe9EoaSx
I have a couple of these offset mounts, as well as a couple of sets of their US made scope rings. Zero issues. Even have much older imported UTG rings on my 10/22 for over 10 years. Made Rifleman with them in 2011, and shot it a few months ago. Still zeroed. Even like the Accu-Sync sights, and have a set on one AR, and recommend them to all my beginner friends for their new builds. Never had a complaint.
Best mount. I have a few. They aren’t as good as the expensive ones but they are close and are way cheaper
Price v performance is huge.
Great vid. Appreciate you reviewing products across a wide price range.
I want to review lower end stuff. But people keep on sending me more and more expensive stuff lol
These are really great. Lighter than a Warne X-Skel, stronger than an Aero ultralight(those break if you look at them angrily, I've broken 2 with no rough handling.) cheaper than anything else worth your money. And unlike the Aero it can handle abuse.
The QD one is about $70 and is every bit as good the non-QD. I have a few of these and a pair of qd and I love all of them, though the QD are the only ones that are in use.
Good to know. I'm going to try to get a qd one for testing
Oh hey, I currently have one of these holding my RT-6 onto my AR. My only concern with it is the steel base screws into the aluminium threads, but the torque specs are well within what should be fine, and I haven't stripped any or had them come loose in the couple of times I've removed and re-attached the mount.
The majority of mounts are steel into aluminum. Its only when you get into more expensive mounts that are either made of 7075, or have stainless threadserts in that you dont have to worry at all about it.
@@CDOES Oh yeah, it's far from the most expensive mount that does this. Full recommend based on very limited use in my experience.
I got an improperly machined one. Hit it with a file to remove the massive machining booger but it was almost bottoming out in elevation still. Gave it to a friend in need and let him know. Spend a little more and get a Warne.
I just bought this
I've bought their stocks , grips , handguards , scope rings....
I have yet to be disappointed. The ar10 super slim free float..
I wouldn't trade it for a Seekins or MI. As for made in China I think their made in Michigan and have been since 2012.
Great video! I would love to see you review the QD version. Especially if you test its return to zero.
With how successful this has been. I do believe it is warranted
@CDOES I second that request. My concern is the lack of full tang for the picitany rail.
Then, the fact that it does not have steel insert in the threaded area.
Bought a New-Old-Stock Gen 1 UTG Recon 360 Bipod, only design flaw is that it needed longer/tighter Allen M2 tension screws on the ball joint. Now it holds better on adjustment. Has full cant and tilt for a bipod, $60 for $200-300 functionality.
A short video showing how you level scopes would be appreciated.
Things you can't unsee: the thumbnail for this video looks like two sleestaks from Land of the Lost. That's a plus in my book.
I think the wedge type scope mounting system is the way to go. It even keeps the Aero Precision mounts from twisting while torquing them down.
Not with the SPR style mount, it sucks so bad to center because there's no flat part to center the scope
@@cakeeee4 Oh damn, I haven't tried those ones just the extended type.
I machined myself a set of parallel wedges that work with most mounts I've used. It takes almost no time at all to level a scope.
Their entire Accu-Sync line is solid.
Im going to have to check out some more of their stuff.
Insane product for the value. Great video
I'm glad you did a video on this. I've used these mounts and would recommend them but everyone would laugh at me because it's UTG.
UTG does have some sleepers. Their receiver extensions, offset rds mounts and these scope mounts have all worked great for me. I still run some of their products and this is coming from a guy who's into ADM, Badger, Scalarworks and Geissele mounts.
It's almost like, if something is good, it's good
They have some free float handguards that perform way above their price point too.
I have lots of high end scope mounts and several of these UTG mounts...the UTG's are every bit as good at less then half the cost. Monstrum also has some really good mounts available for a reasonable cost; especially their 7075 Pro Series and Razorclaw series. With today's CNC machining tech, there is no need to spend $300-500 for a great scope mount.
I use a UTG leapers scope on my AR. $145 on amazon, its held zero fine for over 1000 rounds now. UTG makes good products.
Thank you, Mr. C !
My pleasure
I more or less accidentally bought this one. I went to pick up my 3000€ AR, already bringing my 800€ ish Hawke Frontier thinking I could also pick a mount. Well, got a heart attack when I saw the prices. So I cringed really hard and bought the 80€ mount 😂
Honestly, I did a good job so far. I’ll still replace it when I’ll move the scope to a .308 DMR.
I like the 5 engagement blocks. This scope mount im going to have to add to my UTG scooe mount rail i just ordered for my M1A
I have a UTG I used for my vortex Strike Eagle. Budget optic with a budget mount. Zero issues. Don’t need to spend all kinds of money for a good optic/mount set up.
Thank you. I was actually scrolling looking if anyone had this mount/scope combination. I'm between UTG and Warne.
@@jguerrero0311 I like it. Once I figured out how to get it tight. Don’t necessarily like that design as far as the way it fastens on but once I got it on and tight I haven’t touched it since.
I've used one of these for a year. Zero problems. Excellent for the money.
Just saying you are one of my Favorite channels today
Recommendation for a good place to look for used scopes? Fantastic Channel,Thank you.
Hi C, I never wondered about this and there's a good chance you mentioned it at some point already, but are you from Boston or somewhere around?
For context, I'm a foreigner, have very little knowledge of US accents, but the "cost effective" at 2:10 certainly made me perk up :D
I am somewhere in the north east. A few breadcrumbs are floating around my videos.
@@CDOES Oh man I'll make nothing of the breadcrumbs. But it's somewhat pleasing that I wasn't completly wrong with my suspicion :D
Ive always wondered, do more pic rail lugs really do anything? Unless your rail and the mount are precision machine matched, id doubt youd get more than one lug engaged at a time.
It's just there to help prevent the mount bolts from shearing off.
thx
Any chance the QD version review is coming soon? I’m thinking of either this one or the aero LW for the primary arms 1-6 nova 🤔
Thanks for your amazing reviews!
If you dont mind me asking, which mount did you pick for your 1-6 PA?
@@jguerrero0311 hey. I actually returned the nova. Was a great scope but decided on the PLxC in peanut butter color as it went with my theme. The mount I’m using is the badger ordinance 30mm 1.7” they don’t perfectly match in color but they look really good together.
I had the utg qd mount for a bit but decided i didn’t like the look. I think it’s good for the money tho.
I run these and the non QD "pepr" mounts and they get quite abused and have no complaints. I get a good bit of hate when i run optics like my 1-8 credo in them lol. I've dented my credo on a one of many concrete drops and still held zero. I also quite like the bubble level top cap you can get on them. haven't messed with their offset dot mount as it's not my thing.
I own 3 of these. They are fantastic mounts!
Some people want to po po UTG products , how ever i have used and still use some and have had no issues. I do think they "UTG" are under rated.
I’ve used these a
Few
Times they’re great. I also
Have use the “pro” rings on a few setups. They’re excellent for what they are. Very good quality. But they have odd part numbers to figure out what to get with the offset and all that overalll though excellent
Got one of these when I bought a used Stryker hd 1-6. Pleasantly surprised with it, ended up replacing it with a larue for the rifle I put it on but it will be great on a 10/22
12:45 🤯🤯🤯🤯🤯🤯🤯🤯
I don't think I've ever seen your face on screen.
Even when you were doing the competition you were mostly incognito.
I have a bunch of these, one in particular (high profile 30mm with 50mm offset) i had a utg 4-16 scope in it on an ar, that scope is ok, not the best by any means but it tracks decent and holds zero, but anyway i had the rifle slung across my back, and i slipped on ice walking down the driveway. Fell straight onto the front top of the scope. The scope did end up bending but not enough to notice until shooting it, that scope may still be ok but i replaced it and reused the same mount. Mount is completely fine and this is my personal #1 recommendation for an ar scope mount. These things are solid and you can sometimes even find em for about 25 bucks new, the most ive paid for one is 35 and i have like 6 or 7 of em. Never had any issues with zero using these mounts. I want to try out their qd version as well. Also their little 50 dollar rheostat red dot is surprisingly good, it holds zero and doesnt blink like the vortex strikefire 2, the utg pistol red dot however does have that flash, the screws came loose (the factory installed top ones) and it had water spots for like a month after submerging it. It does however still work just fine, the water spots are now gone, and it has held zero since tightening those but i cant recommend that one. Overall their optics and mounts are solid with a few outliers, also i love my utg t1 riser and it looks cool to boot. Also theyre like 20 bucks and are solid.
Edit: spelling
Cssss I like this mount. But I have reservations putting it on a ar10 308w with a heavier 1-6x24
Properly torques and maybe even blue loctited, you might be fine. If not a Badger is in your future.
Wow over 100 here in Canada
The arken 20 moa cantilever mount is 50 bucks and pretty great I run them on all my ars now.
At that Amazon link in the description?
Photo of a chinese dude larping with a plastic airsoft ".50 cal"
Priceless!
UTG
Uighers Turned (into) Glue
@C_DOES I’m curious if you have experience with the vector optics 1-6 (continental?) that focustripp looked at. I’m curious to see your opinion
That's a kick ass shirt
I want to see the UTG 1-8x28 LPVO review, this thing seems pretty good for the price.
How would you compare this to the Leupold Mark AR Mount?
what is the height to centerline?
I was looking for a scope mount a few months ago and couldn't believe how much Larue Tactical mounts are now. I though it was a typo! 😳
Can you use the arisaka scope leveler kit on this or doesn’t it not have enough real estate on the base because of the skeletonization
Never understood why these companies price their mounts at $100-$300….insane! Glad we gave some companies that produce quality at a good price.
It would be really cool for you to get the monstrum pro mount on the channel. It's 7075 and if I was a betting man the monstrum and utg are manufactured by the same people (at least the chinesium utg stuff).
Interesting....
I still don't know which optic. to buy.
Primary Arms 1x6 Nova :)
Their Aimpoint Micro and angled Mlok mounts are legit
Interesting review. Now what about the best budget mount that has quick release?
Trying it for a while, seems pretty solid for a cheap mount. Just wish it came in different height options without having to use a riser so I can clear my tape switches and the thumb on top of it
One could hope theyd come out with different heights. And maybe more usable colors. But who knows.
The website lists there being a medium and high height profile option to select from, is the high not high enough?
@@KyleJohnsonVA high is 1.6" centerline so pretty much AR height
@@KyleJohnsonVA the 34mm can go higher, but that's 34mm
Trijicon RCR and RMR HD any time soon?
Do you know anything about Precision Reflex Industries' 30mm cantilever mounts? Any recommendations on a budget friendly 30mm mount that has a rmr mount at the 12 o clock position?
I have an optic if like to send to you. If at all possible let me know how I can do this.
Curious how some of the Monstrum Pro Series (7075), or other mounts would fare?
There is only one way to really find out.
I’ve got one of these on an ar and a set of their rings on a prs rifle and both are pretty nice
I have the qd version of this and it's surprisingly good
Nice. That will be worth looking into as well.
I just yesterday put the one inch tube version on my Tavor 7 and shot 200 plus rounds of .308 with no slipping or accuracy issues. This thing is awesome and fairly lightweight!
very good review!
Good mount i have 2
Mint.
love your channel. best reviews
I just love your videos. Keep it up!
What mount do you recommend for a 1 inch scope tube? (on an AR)
I have an aero precision mount. It corroded where the screws go at the clamping point to the mount and I basically had to break it off. I usually just stick to the Burris mounts even though they are heavy. Would love to see the follow up to this mount. As always, thank you for your videos. You are a must view before purchasing optics.
That really sucks about the aero.
@@CDOES I was very surprised when I saw that.
man, really makes me kind of regret spending 300 bucks on badger ordinance mount. I run the acro topside. However, it's stupid high. I've been desperately looking for a mount to replace it and lower the acro a bit. Do you know of any top plates that could replace one of the top rings
Another good budget mount is the Hiram. It was around before PA released their $220 version. It’s $30 with 3 bolts and 2 recoil lugs. I’m wondering if PA’s RMR ring topper will match the mount though.
I wonder if UTG makes a "Red Dot RDS" piggyback top ring for this. Main reason I'm a fan of these is no knuckle-hazard. Most economical mounts will rip your fingers on special/non-AR platforms.
Here you go. a.co/d/2B9MrbN
Just run a diving board of you want a rds mount
Actually it does make such top rings
@@emkro UTG ACCU-SYNC Leveler II with MRDS Mount - RMR + Docter footprint. You're right!
Leapers UTG 1-8x28mm MRC + this mount for about $200. could you test this scope? I'm considering this offer.. thanks
The machining does look good. I have their super slim keymod handguard. Machining is excellent on that
I was looking at getting one of those. Its exactly what I want for a AR.
@@CDOES I got mine from optics planet like 8 years ago. It's still one of the better handguards I have. Love keymod.
Don't overlook their fixed iron sights. They are very nice for any money.
@@johndecker9983 mint
Thanks Brother. Another nice review of something I’ve been eyeing lately. I just finished a dedicated .22lr upper and I think this would be a perfect mount for it.
I only see one issue but it’s irrelevant for my above use. UTG make a piggyback RMR ring cap for this it’s really tall. Theirs is high enough for an MPVO with a large elevation turret but way too high for most LPVO turrets.
But yeah, this looks like a great option for a budget, .22, or beginner gun. UTG gets some hate but I’ve never had a bad experience with the few things I’ve had from them.
This would be choice for you.
I own three of these, and I have been happy with them for the price, and they all have Meopta scopes in them. 😊
Great to hear that.
Thanks, and if you think the optika6 is nice you should look through an R1 or ZD model, I have two R1s one ZD, and 6 optika6 scopes and one optika5, my favorite brand, I do own Steiner and Leupold too. Love the videos!
@@FS-ig2tt I want more Meopta's. I also want them to respond to my emails about a ffp 2-12 lol
Oh a 2-12 ffp would be interesting and nice an AR or hunting rifle or one of my 10/22s, I am surprised they didn't reply. They replied to an email from me in a matter of hours, but that was for Scope turret covers I left in the woods they did send new ones at no cost though.
I have a bunch of these! The only reason not to use them is if you want to save a couple ounces then go with the Aero Precision lightweight. It's twice the cost and not as strong however!
I've broken 2 AP mounts, so at least being out 40 bucks is better?
Id absolutely go with this over the AP, even if Im counting oz's. Id much rather have the added strength
I have been waiting for over a year to see this review. Looks like there is a lot of bang for the buck. I have two of their smaller risers that use thumb screws and I have been impressed with the manufacturing quality. With that said, they over spec their torque settings. I have the UTG OVER BORE BIPOD and the Torx screws stripped when I attempted to remove the bipod.
I definitely see that, which is why I made the comment I did. Youd probably be fine with 20in/# on the main mounting area as well.
Have a couple of these and a couple of offset rds mounts. The handguards aren't bad either.
Wuhan to the wescue! Lol
Cowboy Bebop shirt. Noice.
Damn, the secret is out. It's not perfect but it is really good for the price
It was due to happen. Not theyll all be $80+ haha
I roll with Hiram 30mm mount Cost 26 bucks on amazon
Bummer that they don't sell 34mm with 20 moa
They do actually ….i ordered the 34mm 40 moa mount off Amazon , no other website had them in stock . Supposedly they have 20 & 30 moa mounts as well .
I have a cheap UTG QD mount that feels loose.... but off and on, and the dang thing holds a decent zero. Never more than an inch up or down, and half the time, perfect zero.... 🤔 It has no right being that good.
I bought a UTG QD endplate and it has a weird slant on it that makes me not want to stake it, so I just ugga dugga'd it a bit, but thought that was weird
This thing will save me almost 2oz over my cantilever sport mount though, so ill probably check it out. I'm just using it at a range
The known failure points of the Aero mount are why I decided against it at the last second in favor of a Leupold Mark AR mount instead (plus the Leupold was cheaper.) This UTG mount does look like another decent alternative to consider in the future.
Don't put this on any serious rifle lol.
Expensive mounts for ARs is super stupid That one is spot on. I have expensive mounts. Really is a bunch of bs. Guy good stuff for bolt action. Daum upper is aluminum anyways. Not going to be but so strong to start with. 😂😂😂😂
Monstrum tactical got some good mount too
Got it for $30 bucks
I own several UTG picatinny risers for red dot optics. Top top quality. The next step up in performance would be Scalarworks. But at 5x times the price!
If your looking to keep the weight similar, and the overall profile, yeah.
Lmfao there are things way better then UTG without spending scalarworks money. ADM makes good quality stuff while being relatively budget
I wouldn’t mind trying one but UTG has a terrible stigma in the community.
Can you explain please or you gunna make me google it
@@FederalPacificEh there are certain brands that have a bad stigma in the gun community and no matter how good their new offerings are, they will never break into the enthusiast circle. UTG is one of those brands.
@@FederalPacificEhfor about 10 years UTG was potmetal chinese crap until they started their made in usa “pro” line. It’s going to take a long time to shake that bad rep.
Troy
I guess I can come out of the closet now. I have 3 of these: two 30mm and one 34mm. Bought the first one out of curiosity and couldn’t find anything wrong with it, so..
Sooo full send it.
I love that utg/leapers stuff is cheap, fits together well, at least mine does, their lower third t2. I use it with a holosun 503r gold, and I also like supporting American manufacturing.
Its a real bargain imo
Took you long enough to review these. Between their "medium" and "low" and a half inch riser, you can experiment with multiple scope heights for less than 200 dollars, like 1.79 height. Meanwhile people were paying up to 300 dollars for a single 1.70 badger mount.
Wish they still sold their fde versions.