Recently I changed the belt and rollers on my Scarabeo 500 GT. I didn't know then that the rollers could be directional. Now I'll need to remove the variator and make sure they're correctly oriented. I'm new to this scooter stuff and vids like this give me the information I need to help me keep this great scooter running smoothly.
GREAT JOB GUYS..YOU ARE FANTASTIC AND VERY PROFESSIONAL.WE SAVE A LOTS OF MONEY.THANK YOU.PLEASE UPLOAD A VIDEO FOR BEVERLY 350 FOR CHANGING SPARK AND BRAKES AND IF YOU CAN FOR THE VALVES SETTING. CONGRATULATIONS FOR YOUR EXCELLANT JOB YOU ARE DOING...
hello, this morning I noticed a very small loss of coolant leaking to the ground .. looking below, I notice that the leak comes from above the manifold of the muffler (we are talking about dep beverly 350) what should i start checking? the moped has 30,000km and has never changed the water pump or replaced the liquid inside Thanks for the attention
Thanks for the video! I just buy a used 07 Piaggio MP3 250IE I changing out all oil to it & need check belt & rollers next! The first owner told me he unhook one of sensor inside go to tilt lock i trying find out what is that?
Ciao Beverly 350 e simili con frizione multidisco, se si rompe la cinghia possono anche bloccare la ruota posteriore cone su quelli con frzione ceppi? Che si blocca la campana? O non riesce?
Very Professional like always ! I have one question for my Piaggio Skipper St 150cc 4t ..because I wanna buy this kit ..It's the same torque or is diferent ? Thank you and congratulations for your job ! Come to México !
Volevo chiederti un aiuto ho il beverly 350 anno 2013 ho rifatto tutto il motore completo come gruppo tecnico guarnizioni ecc pompa acqua nuova ecc.. dopo averle fatto spurgo liquido refrigerante... percorsi circa 40km tutto perfetto...ad un certo punto mi esce fuori da tappo di scarico liquido refrigerante liquido da li non posso capire il perché...il livello era perfetto
Hi Vespa Motorsport, I need your help urgently. I recently did my belt change with the roller weights at my local piaggio dealer for my x10. For some reason, whenever my bike idles, it has rattling noise coming from the variator bit. I tried sending it back to the dealer, but they failed to solve the issue 4 times. Does x10 has washer on the variator too? Regards
WHAT does the kit actually do? More power/torque? quicker? More horsepower? What are the down sides, if any? Does any body know please? Thank you very much.
Where do the clutch springs go. You show them packaged at the beginning, malossi 2915398, but not where and how they installed. (I just brought the big kit you showed and the small clutch spring kit to a dealer for installation and when I got home I found they never opened the small clutch springs).
You don't need one. Just use a normal wrench to unscrew and a wrench + torque wrench to tighten up. What you need is the locking tool (see 14:07). That is universal.... Have fun and some helping hands
Robot, I don't see you installing the little clutch springs! - You say at the beginning that you will install springs and at the end that you installed the medium Springs. Everyone sells them and as far as I can tell nobody has ever installed them. So strange. Where do they even go?
Hello, I'm thinking to buy the bv350 I would like to know if I'll instal the malossi exhaust and the variator piaggio service still cover the warranty or I'll loose all the factory services. Thank you
maps.app.goo.gl/?link=www.google.com/maps/contrib/102177458388576770146/photos/@22.1294204,-103.2807825,5z&apn=com.google.android.apps.maps&amv=914018424&isi=585027354&ibi=com.google.Maps&ius=comgooglemapsurl&ct=ml-base2-nlu&mt=8&pt=9008&cid=971944613087325591&_fpb=CIAIEIAGGgVlbi1VUw==&_cpt=cpit&_iumenbl=1&_iumenblab=0&_iumbopn=0&_iumchkval=1&_iumchkactval=1&_iumalttxt=0&plt=950&uit=6499&_fpb=CIAIEIAGGgVlbi1VUw==&_cpt=cpit&_iumenbl=1&_iumenblab=0&_iumbopn=0&_iumchkval=1&_iumchkactval=1&_iumalttxt=0&plt=950&uit=154184&_fpb=CIAIEIAGGgVlbi1VUw==&_cpt=cpit&_iumenbl=1&_iumenblab=0&_iumbopn=0&_iumchkval=1&_iumchkactval=1&_iumalttxt=0&plt=950&uit=329913&_icp=1 burg a scootersbuurgmanscooters
Thank you for the videos! Can you help me? There's a strange noise on my scooter, do you know what it can be? I have searched the internet but I have not found a solution yet, the noise is exactly like this: ruclips.net/video/AB-94sqWpDY/видео.html The noise only appears in idle.
Recently I changed the belt and rollers on my Scarabeo 500 GT. I didn't know then that the rollers could be directional. Now I'll need to remove the variator and make sure they're correctly oriented. I'm new to this scooter stuff and vids like this give me the information I need to help me keep this great scooter running smoothly.
I just Bought this scooter yesterday and I'M in love with it. this machine is nice and power full. 😋
Thanks for the video. My mechanic also greased the rollers. Would this have any negative effects?
You're doing God's work out there!
I got it today on my Medley 125. Thanx...👍🙂😎
Great video! I wanna change my rollers for the first time and this video will help me big time. Well done
Excellent description... many thanks and greetings from Vienna👍
Just bought my first parts from you guys, love ‘em!! Great video!! Thanks guys!!!
Great video! Impressed with piaggo's drive line on the BV350.
Just want to thank you for your great work, super appreciated.
Just ordered my BV350
Thanks guys 👍
GREAT JOB GUYS..YOU ARE FANTASTIC AND VERY PROFESSIONAL.WE SAVE A LOTS OF MONEY.THANK YOU.PLEASE UPLOAD A VIDEO FOR BEVERLY 350 FOR CHANGING SPARK AND BRAKES AND IF YOU CAN FOR THE VALVES SETTING.
CONGRATULATIONS FOR YOUR EXCELLANT JOB YOU ARE DOING...
WELL DONE guys.
Thank you.
BRILLIANT.
Hi Robot, i didn't see the clutch in that bike, or different with ather piaggio small one?
Just installed one of these on my 2020 BV350....already have Malossi exhaust and red hiflow air filter
Hot Rod City!!!
Great videos here - I learn so much! Are the part numbers the same for the BV250 as for the BV350 If not can you post them please? Thank you.
hello, this morning I noticed a very small loss of coolant leaking to the ground .. looking below, I notice that the leak comes from above the manifold of the muffler (we are talking about dep beverly 350)
what should i start checking?
the moped has 30,000km and has never changed the water pump or replaced the liquid inside
Thanks for the attention
Is the 46mm nut on the clutch to change the spring on the 350 the same size as on the 300 thanks .
Thanks for the video! I just buy a used 07 Piaggio MP3 250IE I changing out all oil to it & need check belt & rollers next! The first owner told me he unhook one of sensor inside go to tilt lock i trying find out what is that?
Ciao Beverly 350 e simili con frizione multidisco, se si rompe la cinghia possono anche bloccare la ruota posteriore cone su quelli con frzione ceppi? Che si blocca la campana? O non riesce?
Great video, thanks!
What LED bulbs did you install?
I was wondering, in order to buy a nice pair, if this bike need can bus as modern cars or not...
Thanks a lot.
Very Professional like always ! I have one question for my Piaggio Skipper St 150cc 4t ..because I wanna buy this kit ..It's the same torque or is diferent ? Thank you and congratulations for your job ! Come to México !
Hi, are these steps good for the Piaggio 09 MP3 500? I have 6k miles and the belt alarm blinked yesterday but turned off.
Is it good put some grease on pullers and guides (red parts of plastic)?????
This is awesome! What is the new top speed?
Volevo chiederti un aiuto ho il beverly 350 anno 2013 ho rifatto tutto il motore completo come gruppo tecnico guarnizioni ecc pompa acqua nuova ecc.. dopo averle fatto spurgo liquido refrigerante... percorsi circa 40km tutto perfetto...ad un certo punto mi esce fuori da tappo di scarico liquido refrigerante liquido da li non posso capire il perché...il livello era perfetto
Do you recomend malossi or polini variator kit? maximun speed?
Hi Vespa Motorsport,
I need your help urgently. I recently did my belt change with the roller weights at my local piaggio dealer for my x10.
For some reason, whenever my bike idles, it has rattling noise coming from the variator bit. I tried sending it back to the dealer, but they failed to solve the issue 4 times. Does x10 has washer on the variator too?
Regards
WHAT does the kit actually do? More power/torque? quicker? More horsepower?
What are the down sides, if any?
Does any body know please?
Thank you very much.
quicker acceleration and also top speed increases
Where do the clutch springs go. You show them packaged at the beginning, malossi 2915398, but not where and how they installed. (I just brought the big kit you showed and the small clutch spring kit to a dealer for installation and when I got home I found they never opened the small clutch springs).
For this scooter. It dont take springs. It's a wet clutch
Awesome awesome awesome! What if you don't have an impact wrench? I would like to put the 946 Malossi Variator kit on my new 946.
You don't need one. Just use a normal wrench to unscrew and a wrench + torque wrench to tighten up. What you need is the locking tool (see 14:07). That is universal.... Have fun and some helping hands
try a hammer and chisel
Is the 64mm nut on the clutch to change the spring the same for the 300 before I buy one thanks .
46mm
Non ho capito bene il peso dei rulli variatore? Sono quelli presenti nel kit o vanno comprati a parte
?
Muy Buena!!! Well Done!.
Robot, I don't see you installing the little clutch springs! - You say at the beginning that you will install springs and at the end that you installed the medium Springs. Everyone sells them and as far as I can tell nobody has ever installed them. So strange. Where do they even go?
there are no springs in this clutch
@@richarddegen6184 I believe it, And yet he shows springs and says that he installed springs?
Hello, I'm thinking to buy the bv350 I would like to know if I'll instal the malossi exhaust and the variator piaggio service still cover the warranty or I'll loose all the factory services. Thank you
We would suggest referring to the factory warranty paperwork, it should outline aftermarket & performance parts. Every country is different.
ok thank you
I’m seriously thinking of getting one of these but I’m 6ft tall, will it be big enough for me?
yes
oh, where are 3 clutch shoes and clutch bell on this scooter?
There aren't any, as this has a wet clutch housed in the final drive.
hi I was wondering if u have the full upgrade set up for rupp scooter 2014
great video.
MARYK piaggiompscooter
Piaggiom
maps.app.goo.gl/?link=www.google.com/maps/contrib/102177458388576770146/photos/@22.1294204,-103.2807825,5z&apn=com.google.android.apps.maps&amv=914018424&isi=585027354&ibi=com.google.Maps&ius=comgooglemapsurl&ct=ml-base2-nlu&mt=8&pt=9008&cid=971944613087325591&_fpb=CIAIEIAGGgVlbi1VUw==&_cpt=cpit&_iumenbl=1&_iumenblab=0&_iumbopn=0&_iumchkval=1&_iumchkactval=1&_iumalttxt=0&plt=950&uit=6499&_fpb=CIAIEIAGGgVlbi1VUw==&_cpt=cpit&_iumenbl=1&_iumenblab=0&_iumbopn=0&_iumchkval=1&_iumchkactval=1&_iumalttxt=0&plt=950&uit=154184&_fpb=CIAIEIAGGgVlbi1VUw==&_cpt=cpit&_iumenbl=1&_iumenblab=0&_iumbopn=0&_iumchkval=1&_iumchkactval=1&_iumalttxt=0&plt=950&uit=329913&_icp=1 burg a scootersbuurgmanscooters
I'm sorry i'm not english and i can't understand. He told 26 o 126 NM?
LOL it is fun to do that to the cruiser bikes off the light LOL
It is the same in beverly 300ie (greek model)
Does it fit on a Beverly 300?
Damn so few videos about BV350...
What speed win !?
which gram rollers you put in that variatore malossi man ?
Did you even watch the video
will this work on the x9?
How often must i change this kit in my bv350 ?( How many km? )
you are not showing how you put the roller in
genial
great informative video
please do piston replacement video, im willing to pay
send the money first
where is clutch in this scooter
It's a wet clutch. No spring clutch. The clutch is behind the cover by the gears
You guys hot the wrong variator the j Costa is the best and almost doesnt ware out
Thank you for the videos! Can you help me? There's a strange noise on my scooter, do you know what it can be? I have searched the internet but I have not found a solution yet, the noise is exactly like this: ruclips.net/video/AB-94sqWpDY/видео.html The noise only appears in idle.
50cc
хватит болтать - работай!