Thank you so much for your video. Upon moving to dryer in my house, buttons work fine, with pushing start it only clicks and won’t start. Is there a video for placing the belt or replacing the belt? Thank you
Hi Josh, We have this same exact dryer. This morning I turned it on and the two black relays on the control board click but it does not run. Come to find out, the belt is broken. Is that more than likely the whole problem? Or, should we investigate further? Funny, ....... Our thanks, The Cobb Family 😀
Hi Josh - mine was working fine, then I leaned up against it to reach my water supply behind it and now the power won’t go on. There is power though because the drum light is on. I feel like maybe I locked it inadvertently but don’t know how to fix it. Can you help?? I have unplugged it and cut the power breaker for up to 6 minutes twice. That didn’t work.
Hi Josh. I bought the same dryer at Habitat of Humanity Restore. My contractor and I we're looking up the specs on the dryer. Came with no hoses/plug nothing. We don't see a gas line visible on the back. Any direction where to start will be most grateful. I might have to return it. It's more of a headache than the savings I received from the purchase.
I have the same one and i put one of the cycles and it says 45min but 5 min later it shows 15min left why is that? How can i fix it so i can dry for 45min exactly?
Clean the moisture sensor, it's inside on the plastic housing where the lint trap lives. If it gets blocked or jammed up with little bits of gunk the dryer won't know how wet the clothes still are and it reduces the time. Good luck!
Today we moved my dad's washer and dryer into our home and the washer works wonderfully. While trying to start the dryer all the lights and dials and buttons work great. But when press and holding on the start button I get 3 rapid beeps. Any ideas as to why? TIA
Belt probably broke or could have been knocked off the idler pulley when moving. Sometimes you can take the back vent housing off and access the inside of the dryer that way. I have reached through there and placed belts back on the tensioner pulley several times using this method. Other times especially if the belt is broke you’ll have to completely disassemble to replace the belt.
It’ll range between 95 and 195 F depending on its cycle. You should see about 250F if you measure right inside the heating element tube while it’s actively heating. Sometimes when these heating elements break they will arc weld to the frame and half work, not producing the proper heat.
I would check your moisture sensor, which is typically found inside on the plastic of the lint trap holder. It’s a long metal sensor and if it’s clogged up dirty or broken, this can cause your dryer to think the clothes are done when they’re not.
could be several reasons. Heating element, thermistor sensor, control board. You'd first want to check and make sure the air flow isn't blocked on the back of the dryer or lint trap.
@@joshcobb4100 I just realized the guy that came order a Flat Igniter Dryer, he was supposed to come for the past 2 weeks to put it on but hasn't is that something I can do myself? My dryer broke exactly 1 month ago and I have the piece he order for the past 2 weeks and he keeps on canceling on me 😕
Just by watching your videos, I find washers and dryers that people I know used to have. You may have earned yourself a follower.
Thank you so much for your video. Upon moving to dryer in my house, buttons work fine, with pushing start it only clicks and won’t start. Is there a video for placing the belt or replacing the belt? Thank you
Gracias por el video porque no sabía cómo prénderlo .😃
Cómo le hociste?
@evermiranda2995 Mantén pulsado el botón de inicio.
@@joshcobb4100 muchas gracias!
Hi Josh, We have this same exact dryer. This morning I turned it on and the two black relays on the control board click but it does not run. Come to find out, the belt is broken. Is that more than likely the whole problem? Or, should we investigate further?
Funny, ....... Our thanks, The Cobb Family 😀
Hi Josh - mine was working fine, then I leaned up against it to reach my water supply behind it and now the power won’t go on. There is power though because the drum light is on. I feel like maybe I locked it inadvertently but don’t know how to fix it. Can you help?? I have unplugged it and cut the power breaker for up to 6 minutes twice. That didn’t work.
Hi Josh. I bought the same dryer at Habitat of Humanity Restore. My contractor and I we're looking up the specs on the dryer. Came with no hoses/plug nothing. We don't see a gas line visible on the back. Any direction where to start will be most grateful. I might have to return it. It's more of a headache than the savings I received from the purchase.
If there is no power cord and you don’t see a gas hookup it’s probably an electric 220v dryer, not a gas dryer.
How much did this cost?
When I push the button to start it I can hear three clicks and the machine won’t start
I have the same one and i put one of the cycles and it says 45min but 5 min later it shows 15min left why is that? How can i fix it so i can dry for 45min exactly?
Clean the moisture sensor, it's inside on the plastic housing where the lint trap lives. If it gets blocked or jammed up with little bits of gunk the dryer won't know how wet the clothes still are and it reduces the time. Good luck!
Today we moved my dad's washer and dryer into our home and the washer works wonderfully. While trying to start the dryer all the lights and dials and buttons work great. But when press and holding on the start button I get 3 rapid beeps. Any ideas as to why? TIA
Belt probably broke or could have been knocked off the idler pulley when moving. Sometimes you can take the back vent housing off and access the inside of the dryer that way. I have reached through there and placed belts back on the tensioner pulley several times using this method. Other times especially if the belt is broke you’ll have to completely disassemble to replace the belt.
For kenmore elite what temp should it be at for medium and high heat?
It’ll range between 95 and 195 F depending on its cycle. You should see about 250F if you measure right inside the heating element tube while it’s actively heating. Sometimes when these heating elements break they will arc weld to the frame and half work, not producing the proper heat.
My kenmore elite HE5 power button is stuck
Mine ain’t actually turning on any ideas?
Start with third grade grammar lessons. You’re not ready for anything more advanced yet.
Hi why would my lights on the panel go on and off also not drying completely and just turns off it self
I would check your moisture sensor, which is typically found inside on the plastic of the lint trap holder. It’s a long metal sensor and if it’s clogged up dirty or broken, this can cause your dryer to think the clothes are done when they’re not.
Thanks I will check it out
Mine water is not going into tray, why not?
No idea. You would need someone to evaluate it.
my dryer dont work after i reset de screen
How to do that ? I mean reset
Mine is not heating up why?
could be several reasons. Heating element, thermistor sensor, control board. You'd first want to check and make sure the air flow isn't blocked on the back of the dryer or lint trap.
@@joshcobb4100 thank you
@@joshcobb4100 I just realized the guy that came order a Flat Igniter Dryer, he was supposed to come for the past 2 weeks to put it on but hasn't is that something I can do myself? My dryer broke exactly 1 month ago and I have the piece he order for the past 2 weeks and he keeps on canceling on me 😕
Is it a gas dryer?
Mine was doing the same thing. I Had to replace the dryer blower fan it broke free