Ordered the Rear Seat Release, best purchase I did interior wise. So much easier to get behind the seat. Extremely well built, and best of all made here! Thank You for the cinnamon candy as well. Highly recommend for anyone who owns a 150.
I believe I would have used 3M VHB two sided tape. There are different strengths to choose from and it would also provide vibration dampening. They use it to mount panels on buildings so I'm sure it would hold that and you wouldn't have to take stuff apart. Just use something like acetone to clean the surface before adhering. Hold it in place for a few seconds and you are good to go
Absolutely. If and when it fails scrape off the old tape and repeat. But..... 3M won't fail. Removing those panels there's sure to be alot of guys that don't have the feel and will scratch, mar or break tabs
Maybe it's just me but I haven't seen any QUALITY videos about getting mods like these for older heavy duty pickups. Most that I find just skip the installation. It's good there's people like you that make these videos with a high level of quality
I installed this on my 2016 F150 to mount a small CB/Ham radio on. It was easy and worked very well. Then I had to have a 2018 F150....I hope to install it again soon. Procrastination pays off right now. Great product!!
Ya, that's really good because here in Arizona, that little dash pocket is TOTALLY useless, unless you want a "puddle" of whatever you put in there. I was thinking of a good phone mount that hangs over the front a bit. There's probably a million applications this can be used with. I'll keep this in mind if I have a need to mount something there. Nice vid and you did it all using only ONE hand!! :-)
Thank you for your video! I have a 2010 Ford F-150 and I don’t like drilling into my truck. I find your video helpful because I’ve just purchased the mounting bracket for my 2010 F150! Thank you again!
I wish Ford would have put a wireless charger for phones and ipods up there, but that is a good idea, especially for a CB. Thanks for the review and install!
It appears to me there might be enough room under that center piece to also install a cig lighter plug. Something Ford should have done in the first place. Sure would be nice to have that or, a USB port for using this mount, then a cell phone magnetic mount and not have a cord going down the center stack to the plugs there. The question then would be, how difficult would it be to run wiring for such a plug. Do you think a cig lighter plug would fit underneath in the valley of that center piece?
Gee. All this time I though that little cubby was designed specifically for little small square boxes of tissues. Works great for that. And a couple spare pens. And receipts that I get for work. And my work badge. It is a great feature.
Thank you. I am looking to buy an F-250/350 in the near future, and being a Ham Radio Operator, I am looking for ways to mount, not just one, but two or three radios in the cockpit. The 2 Ham radios I have include remote control head mounting options, with the main body of the radio tucked away somewhere, like under the seat. Unfortunately, no such convenience for my CB radio. This bracket is a nice option for at least one radio, but do you have any suggestions for other mounting options? TIA.
Wait......they included a jawbreaker? Cool. 😊 Love the dash mount. *8k away from 100* _Sorry to keep ranting about this, but you truly deserve the recognition_
I am getting ready to install one of these, but I wonder - wouldn't it be easier to install it with the rack surface away from you, toward the front, basically turn it 180 degrees? That way, mounting/unmounting things, you don't have to try to reach behind and under to tighten them?
You could easily add another flat magnet under the rack to strengthen the grip of your little monitor if needed. Secondly $50 is a ridiculous price for a piece of metal. IMHO. Before you told us the price I was all over getting one. You could also use a bean bag mount ala Garmin I think and just flop in the tray. They’re overpriced too but not to the degree of this product. Again IMHO.
I really don't think that $50 for this product is that bad. Taken into account 4 or 5 shop operations, Laser cutting, press brake, debur, powdercoat, and kitting. Not to mention the amortization of the design process along the way. Plus, since these only fit Raptors and 17-18' Super Duties, 50 bucks is chump change, when the rig is 70 to 90K!
Well, I was all excited about this company right up to the point when I found out they only make products for Ford trucks. Not trying to start a debate but I wish I was able to get more products for my 2006 Ram 2500. Oh well...
Please don't make this thread a nonsensical argument of what truck is better or best... I just was commenting that I wish I could add in something like this for mine. Relax people... It's just a comment.
This is a very good question. Or, has anyone thought of or tried run a USB extension inside and up from the two USB at the bottom of the console? I hate all the wires hanging in front of the console from the DC and USB outlets. Thanks.
Thank you. Really enjoy the video on the dash mount. I am researching a place to mount my smartphone in my "new to me", 2018 F-150. My question is....do you have any suggestions as to where i may look for accessories to mount to this for a smartphone holder/mount?
MrGrunthunter's Adventures Yeah. I think I'd have mounted it as far back as possible oriented 180 degrees too. Plus I'd have left the mat in place. Cool little rack... however you do it though.
I was suspecting that may have been the problem. Didn't know how big your monitor was. Keep up your great videos. I've been learning a LOT. Have recently started doing a little casual research on what is involved in owning and operating an RV vs a fifth-wheel setup like yours and if it's really anymore cost effective over just driving and staying in hotels etc.
@@BTBRVReviews I ordered mine through 'BuiltRight' too and the install is easy. I plan to mount a CB but not sure yet. Nice truck! I have a 2017 F350 King Ranch also. Great vids.
What i did was; removed the little rubber mat, replaced it with a thin metal plate (epoxy). home depo has them in the deck section and the one I got (forgot the size) fits perfectly. I only had to round off the corners. Then got a piece of some carbon fiber looking car wrap to cover it an making it look nice. Then got a phone holder with the telescoping arm and swap the suction cup for a round magnet. Have had it for over a year and works perfectly. And the whole set up cost less than $ 30.00 including the phone holder.
Has anyone figured out or posted a video on how to install some 12v power ports up there in the tray to power the accessories? I have seen a bunch of pictures but no one has done a video on what power wire you need to tap into for power. If y’all could that would be awesome!
Neat mount. Off topic of the video. What kind of mileage are you getting with the f450 not while towing? I'm looking at an 2018, that is a good deal. I have a 2019 350 SRW on order but the fire in Eaton River, MI. Is almost certainly going to delay my delivery date til sometime into October. I know the 3.55 in the order truck will net better mileage, but how much worse is the 4.30? You seem like you drive conservatively. I'm in Canada and will not venture much north or 65 mph ever. Thanks.
So glad I found your channel. Any reason why you couldn't turn the mount 180 degrees and push it closer to the windshield so you could still use that area? Just thinking for my specific uses. Thank you again for a great video.
I've just installed this, JD. Thanks for the guide. What do you think about adding USB power to the base somehow? There seems to be lots of space below the base.
what type of mount did you use for the monitor. i have a similar set up with my 5th wheel. I bought this dash mount, just having a little difficulty finding the right mounting hardware for the monitor. i have a Furion RV camera and monitor, roughly 3"x 6" for the monitor. thanks! Great videos!
Cool Mount! Wish they had something for my 2013 F350. Question: Do you think you will ever have plans to discuss or review tuners/ programmers or modules. Just curious about your thoughts on them. Specifically AG Diesel Solutions or Stealth Modules. Thanks!
I would've just used the 3M Double sided foam tape that has the red backing. No disassembly or drilling need. To remove the mount, use waxed dental floss to cut through the mounting tape. BTW the tray in the console, to the left of the cup holders. My Garage door opener is below the rubber pad. I used a spacer cut from plexiglass and the double faced tape to mount it. I put the rubber pad back in. Now my opener is out of sight, but readily available, with a push on the rubber pad.
I only stayed for the product. I usually stop watching a video when someone is filming with one hand and trying to work with the other. Very annoying. Only thing worse is when someone says “what’s up you tube “.
I like the product & the show, BUT and here it comes. Not to be negative BUT DOT/DPS will be all over you if anything is over the steering wheel blocking line of sight. Also same goes as from the roof line. Cant have anything in the cab hang lower than the top of the rearview mirror. I didn't make the dumb rule just wanted to let you know about it.
, does anyone know why there is a speaker in the center of the dash? I know that nobody uses mono speakers anymore so is this a ( center ) channel speaker ? if so, time for an upgrade while you have your dash torn apart.
Just picked one up and put it in my truck to mount my cb radio. Awesome bracket, very sturdy. Well worth the price
Ordered the Rear Seat Release, best purchase I did interior wise. So much easier to get behind the seat. Extremely well built, and best of all made here! Thank You for the cinnamon candy as well. Highly recommend for anyone who owns a 150.
I believe I would have used 3M VHB two sided tape. There are different strengths to choose from and it would also provide vibration dampening. They use it to mount panels on buildings so I'm sure it would hold that and you wouldn't have to take stuff apart. Just use something like acetone to clean the surface before adhering. Hold it in place for a few seconds and you are good to go
I love 3M VHB tape! I used it to secure my flexible solar panels to the roof of my trailer so I wouldn't have to drill any holes.
Absolutely. If and when it fails scrape off the old tape and repeat. But..... 3M won't fail. Removing those panels there's sure to be alot of guys that don't have the feel and will scratch, mar or break tabs
Maybe it's just me but I haven't seen any QUALITY videos about getting mods like these for older heavy duty pickups. Most that I find just skip the installation. It's good there's people like you that make these videos with a high level of quality
I would turn it 180 degrees and install closer to speaker, this way I could still use the space in the tray underneath it.
Yes but put the rubber back down and mount ontop.
I installed this on my 2016 F150 to mount a small CB/Ham radio on. It was easy and worked very well. Then I had to have a 2018 F150....I hope to install it again soon. Procrastination pays off right now. Great product!!
Ya, that's really good because here in Arizona, that little dash pocket is TOTALLY useless, unless you want a "puddle" of whatever you put in there. I was thinking of a good phone mount that hangs over the front a bit. There's probably a million applications this can be used with. I'll keep this in mind if I have a need to mount something there. Nice vid and you did it all using only ONE hand!! :-)
I have one in my 2017 F-150. It’s been very handy & is well worth the price!
Great idea. I fabbed up something similar to 3D print for for my dash cam. Built Right guys get it.
I like that mount, going to see if I can fabricate something like it for my 2008.
Thank you for your video! I have a 2010 Ford F-150 and I don’t like drilling into my truck. I find your video helpful because I’ve just purchased the mounting bracket for my 2010 F150! Thank you again!
I can’t describe how much I like the new fords
Right? They're unbelievable
Just installed one 30 minutes ago. Pretty straight forward and fixin’ to order a couple of Ram Mount parts.
Great video! Thank you! I have been searching for exactly this solution for my F250, to install a GMRS radio.
I have my CB radio mounted to this in my 2018 F150. I highly recommend it.
I wish Ford would have put a wireless charger for phones and ipods up there, but that is a good idea, especially for a CB. Thanks for the review and install!
Mark Bean wish there was a good place for a CB in my 2016.
Do people still use CBS?
ghostrider wish more did, many accidents and pileups could be avoided.
Cant afford for these trucks to be more expensive
i had this in my 2019 ranger, just changed over to F150, will need to get one, lol
It appears to me there might be enough room under that center piece to also install a cig lighter plug. Something Ford should have done in the first place. Sure would be nice to have that or, a USB port for using this mount, then a cell phone magnetic mount and not have a cord going down the center stack to the plugs there. The question then would be, how difficult would it be to run wiring for such a plug. Do you think a cig lighter plug would fit underneath in the valley of that center piece?
Step bits are the best! They are life changing. Nice vid!
Gee. All this time I though that little cubby was designed specifically for little small square boxes of tissues. Works great for that. And a couple spare pens. And receipts that I get for work. And my work badge. It is a great feature.
Easy peasy. I thought you were going to put a CB radio there but for you a camera only makes sense. Good video.
Wonder how tough it would be to run some power up there. Nice install!
Great video! I think this is my solution for mounting my cb. Thanks again btbrv!!!
So excited about it that i ordered one! Nice job, they should give you a sponsorship. Considering The video will no doubt help their sales.
Getting mine today. Finally get my scanner mounted
Thank you. I am looking to buy an F-250/350 in the near future, and being a Ham Radio Operator, I am looking for ways to mount, not just one, but two or three radios in the cockpit. The 2 Ham radios I have include remote control head mounting options, with the main body of the radio tucked away somewhere, like under the seat. Unfortunately, no such convenience for my CB radio. This bracket is a nice option for at least one radio, but do you have any suggestions for other mounting options? TIA.
Just order mount for my F-250. Will be nice to mount my TMPS and review camera for the RV.
Wait......they included a jawbreaker? Cool. 😊
Love the dash mount.
*8k away from 100* _Sorry to keep ranting about this, but you truly deserve the recognition_
thanks brother!
Itsa Mea
lol 😂
We sadly stopped including jaw breakers. 😢
I am getting ready to install one of these, but I wonder - wouldn't it be easier to install it with the rack surface away from you, toward the front, basically turn it 180 degrees? That way, mounting/unmounting things, you don't have to try to reach behind and under to tighten them?
sharp tools on a leather seat. you like to live dangerously!
You could easily add another flat magnet under the rack to strengthen the grip of your little monitor if needed. Secondly $50 is a ridiculous price for a piece of metal. IMHO. Before you told us the price I was all over getting one. You could also use a bean bag mount ala Garmin I think and just flop in the tray. They’re overpriced too but not to the degree of this product. Again IMHO.
I really don't think that $50 for this product is that bad. Taken into account 4 or 5 shop operations, Laser cutting, press brake, debur, powdercoat, and kitting. Not to mention the amortization of the design process along the way. Plus, since these only fit Raptors and 17-18' Super Duties, 50 bucks is chump change, when the rig is 70 to 90K!
Yeah, thinking that's a little pricey for what it is...
Definitely over priced
$50 bucks...psssh
wreckingballpi And F-150’s
That looks clean and rugged.
Could you possibly tell me what phone mount that is on your dash? Thanks. :)
Didn't see any lockwashers or self locking nuts. Vibration, not could, will eventually loosen nuts. Great videos, subscribed recently.
Indead there were lock washers and flat washers
Nice job multitasking, nice product ,thanks for the video!
Well you had my OCD working overtime but why not order a second rubber mat and use that at a later date and drill through the original? Cheers 🇨🇦
same thing I was thinking
I wish ford would have put a couple extra USB hubs up there.
what monitor mount did you use? what magnets? is there a link to the follow-up video?
Well, I was all excited about this company right up to the point when I found out they only make products for Ford trucks. Not trying to start a debate but I wish I was able to get more products for my 2006 Ram 2500. Oh well...
Not going to buy another truck... I like my monthly payment way too much on the one I own presently. LOL!!!
GM sells more pickups than Ford.
Please don't make this thread a nonsensical argument of what truck is better or best... I just was commenting that I wish I could add in something like this for mine. Relax people... It's just a comment.
Fabfour makes some parts for all kinds of vehicles.
Did you run a 12v outlet up there to plug in your accessories?
This is a very good question. Or, has anyone thought of or tried run a USB extension inside and up from the two USB at the bottom of the console? I hate all the wires hanging in front of the console from the DC and USB outlets. Thanks.
So when you do break one of those white clips where can you get replacements?
Thank you. Really enjoy the video on the dash mount. I am researching a place to mount my smartphone in my "new to me", 2018 F-150. My question is....do you have any suggestions as to where i may look for accessories to mount to this for a smartphone holder/mount?
Submariner Rolex, king ranch, and a titanium bench made...I like the style
Have you thought about using the camera system you can get from ford along with the tpms system that interacts with the sync?
Wow nice king ranch and I seen the color ruby red metallic 🤤
Was the a trim tool a bike tire remove
Looking forward to the video showing the camera installation
Wouldn't it have been better to have mounted the bracket 180 degrees so you would have easier access to the space under it? Just a thought.
MrGrunthunter's Adventures Yeah. I think I'd have mounted it as far back as possible oriented 180 degrees too. Plus I'd have left the mat in place. Cool little rack... however you do it though.
great idea, but wouldn't work for me. the slope of the windshield won't allow the camera screen to fit with the antennas if it's any further back.
I was suspecting that may have been the problem. Didn't know how big your monitor was. Keep up your great videos. I've been learning a LOT. Have recently started doing a little casual research on what is involved in owning and operating an RV vs a fifth-wheel setup like yours and if it's really anymore cost effective over just driving and staying in hotels etc.
@@BTBRVReviews I ordered mine through 'BuiltRight' too and the install is easy. I plan to mount a CB but not sure yet. Nice truck! I have a 2017 F350 King Ranch also. Great vids.
What phone mount is that on top? Has it been good still and not lost its adhesive?
that would be perfect for gauge pods. i like it.
What i did was; removed the little rubber mat, replaced it with a thin metal plate (epoxy). home depo has them in the deck section and the one I got (forgot the size) fits perfectly. I only had to round off the corners. Then got a piece of some carbon fiber looking car wrap to cover it an making it look nice. Then got a phone holder with the telescoping arm and swap the suction cup for a round magnet. Have had it for over a year and works perfectly. And the whole set up cost less than $ 30.00 including the phone holder.
I would drop a wire down through the dash to clean up the area for wiring an accessory
Sweet!
I know this is an old video. Just wondering if placing a magnet on that rack caused interference with the speaker?
Would perfer using something that does not bolt on. Maybe double sided tape?
Need one for my f350 work truck
So, what did you mount on that "BuiltRight" mount. I don't see a video as a follow up...you did mention it ???? (Or I just don't see the link")
I need something like this for a 2008 Ford F350.
Any idea if you can run a cable through to get power to accessories up there?
Has anyone figured out or posted a video on how to install some 12v power ports up there in the tray to power the accessories? I have seen a bunch of pictures but no one has done a video on what power wire you need to tap into for power. If y’all could that would be awesome!
Where you able to get a discount code?
Looks great. What kind of attachments work with it?
Neat mount. Off topic of the video. What kind of mileage are you getting with the f450 not while towing? I'm looking at an 2018, that is a good deal. I have a 2019 350 SRW on order but the fire in Eaton River, MI. Is almost certainly going to delay my delivery date til sometime into October. I know the 3.55 in the order truck will net better mileage, but how much worse is the 4.30? You seem like you drive conservatively. I'm in Canada and will not venture much north or 65 mph ever.
Thanks.
I get around 13.5 unloaded city and 15-17 hwy
So glad I found your channel. Any reason why you couldn't turn the mount 180 degrees and push it closer to the windshield so you could still use that area? Just thinking for my specific uses. Thank you again for a great video.
I've just installed this, JD. Thanks for the guide. What do you think about adding USB power to the base somehow? There seems to be lots of space below the base.
I bought a 2019 F350 and prior owner intalle
Installed one of these and he added 12 plug and usb plug just as you asked about. We use it to hold our RV camera monitor and a cell phone holder
what type of mount did you use for the monitor. i have a similar set up with my 5th wheel. I bought this dash mount, just having a little difficulty finding the right mounting hardware for the monitor. i have a Furion RV camera and monitor, roughly 3"x 6" for the monitor. thanks! Great videos!
Check into Ram Mounts. They aren't cheap, but they look like solid quality.
Going to be Ordering. Did you find out about a discount code?
Cool Mount! Wish they had something for my 2013 F350. Question: Do you think you will ever have plans to discuss or review tuners/ programmers or modules. Just curious about your thoughts on them. Specifically AG Diesel Solutions or Stealth Modules. Thanks!
I would've just used the 3M Double sided foam tape that has the red backing. No disassembly or drilling need. To remove the mount, use waxed dental floss to cut through the mounting tape. BTW the tray in the console, to the left of the cup holders. My Garage door opener is below the rubber pad. I used a spacer cut from plexiglass and the double faced tape to mount it. I put the rubber pad back in. Now my opener is out of sight, but readily available, with a push on the rubber pad.
Would it be a hard job to run a hot wire from the drivers side foot well area up to under the bracket?
Have you thought about a go pro mount to body or hat to allow two hands free? Just asking and great job.
cdLady54 Marengo: Thanks. I probably have 30 different mounts but tend to just hold the camera by hand.
I only stayed for the product. I usually stop watching a video when someone is filming with one hand and trying to work with the other. Very annoying. Only thing worse is when someone says “what’s up you tube “.
If the magnets don't work, you could probably adapt some m-loc mounts for a lot of stuff
The magnets work extremely well. I'd do a video on it also.
I wonder how wide it is for a possible cb radio mount
It is wide enough since it would allow a CB to mount flush
Is that an aftermarket center console cup holder? What is it?
What happens when it’s time to sell or trade in does drilling into the truck decrease value?
Doubtful since the oem rubber mat can cover it
Yeah . Probably cut the trucks value about half
What type of phone mount is that in front of the bin you are installing the bracket into?
I like the product & the show, BUT and here it comes. Not to be negative BUT DOT/DPS will be all over you if anything is over the steering wheel blocking line of sight. Also same goes as from the roof line. Cant have anything in the cab hang lower than the top of the rearview mirror. I didn't make the dumb rule just wanted to let you know about it.
That's a great idea and it will work for a RV GPS to mount to thanks
I think I would have left the little mat in there. Anything that gets in there is going to rattle like crazy and now it looks cheaper.
have been looking for a solution like this for awhile now....thanks
How do you screw holes into something?? Don’t you drill holes?
Ah yes, after watching the rest, he indeed DRILLED holes, and didn’t screw them!
Is the knife you had in the video a Ontario Rat 1?
john weiser yes sir
Who made that phone mount on your dash? I may have missed that video
Drilling that inside your cab?! Gah! That drives me crazy! Cool rack tho
hey there, what phone mount is that ? i like the location ... Thx
Does the added weight intrude on performance or gas milage?
Awesome !!!
Are those slots mlok?
If you turned the rack around 180 degrees, you could still use the space under it.
Look at RAM mounts. You could make a nice movable arm mount.
Whew that was a scary install! What is the mount on the top left of the radio on your dash?
Nice looking piece,but honestly 50.00 is about double what that’s worth,IMO. I was all in until I heard the price lol.
SHORT CUT: Use a few self tappers, done in a minute! Ha! PS - Make your own "metal" bracket!
OMG I have watched engine rebuild videos that took less time! A 7 min video to show how to install a little metal bracket??? I have to go shave now!
More like this! Accessories I can afford! Awesome.
Where's a good place to buy Ranch Hand down here? I'm new to Corpus and am looking for good truck places. Steps,bumpers ect.
C&S Plating! Ask for Al or Rob
Cool thanks
What is it?
I don't get what it's for.
Hey man, that little cell magnet that you have mounted, I like that location. Can you share what magnet that is. Thank you
I was going to ask the same question
Love seeing the comments from owners of a $50K+ truck complaining about 50 bucks for a nice looking/well engineered product. 😅
Why would you drill the part inside the truck ? Also , rubbing the console with the dash part could easily scratch the console. WoW!
, does anyone know why there is a speaker in the center of the dash?
I know that nobody uses mono speakers anymore so is this a ( center ) channel speaker ?
if so, time for an upgrade while you have your dash torn apart.