Halo sir i tried to use same isp but but the problim is during speed test only one isp recognize the speed of two isp is not merging, did you try to same isp in your set up?
Thank you for your comments and support. Directly the ER605 Tplink not having wan aggregation , But put the the both wan as Active-active mode , Once the other line reach load of maximum , it will share the other users to second line. Always connect the high bandwidth line as primary. So your internal team will be complete sharing as complained internet over the sharing.
Thank you for comment and support . You can combine the internet ,But the speed will be separate . Because the working principle of the device is fail over or redundancy .
Thank you for your comments and support. In this case you have to use 10gbps loader balancer, then configuration make as aggregation mode you will get 800+800=1600 speed (small fraction will there based on you network switch and interface card ). But the interface should be minimum 2 gbps in router output
@@abethetechie hi i try dual isp in two the same internet connection but when i speedtest it the result 30-40mbs sometime drops to 25-29mbs my 1 internet speed is 40mbs and my 2nd connection is 40-50mbs i try also use router just to change the IP ADDRESS but still the same can you help how.thank you
You are having same ISP with dual internet . The router will give the features of fail-over or load balancing , it is not having aggregation (means one 10 mbs+20 mbs internet will get 30 mbps that features are not available ) . But this is working based on distribution for example if the internet speed is one 10 mbs other 20 mbs if in the network 3 person are downloading,Based on the load balancing each person will get the 10 mbps speed , Because the 20 mbps split and 10 Mbps will directly allocate as load balancing ( need to set the proper speed in the wan and ratio of the load also ).
1 . Configure 2 ISP on 2 Wan inter face with (ISP router IP should be different ) 2. Configure the upload and download speed on on both wan (Based on the ISP speed ) 3. Enable load balancing ( no need to use fail over ) 4. Set the ratio of the load balancing
Thanks but aggregated up to 2GB is misleading I think. In Multi WAN mode speed is 1/3 of single WAN speed to my testing. Have you tested this and claim and how did you achieve this ?
Thank you for your comments and support. If you are doing the speed test we are able to see aggregate speed. That wan connection is broadband the speed will not be stable. In downloading a file depends on the latency and download server bandwidth setup. Usual download will be we simply calculate the speed 1/3 even in single connection.
![[#2024MAMA] G-DRAGON - 무제(Untitled, 2014)+POWER+HOME SWEET HOME+뱅뱅뱅+FANTASTIC BABY | Mnet 241123 방송](http://i.ytimg.com/vi/Ox29z5Nf1Uk/mqdefault.jpg)
Excellent Video, Lots of great information... The Accent made it a little difficult, but far from impossible. Thanks for sharing, Very good info.
Thank you for your comments and support🙏.
Halo sir i tried to use same isp but but the problim is during speed test only one isp recognize the speed of two isp is not merging, did you try to same isp in your set up?
Thank you for your comments and support.
Directly the ER605 Tplink not having wan aggregation , But put the the both wan as Active-active mode , Once the other line reach load of maximum , it will share the other users to second line. Always connect the high bandwidth line as primary. So your internal team will be complete sharing as complained internet over the sharing.
@@abethetechie maraming salamat
You are welcome.
as my experience converge and pldt, yes na cocombine speed po.
Thank you for comment and support .
You can combine the internet ,But the speed will be separate . Because the working principle of the device is fail over or redundancy .
@@abethetechie yes i got the combination speed.
Good to hear bro
Good day. Can we use ER605 as PPPOE server?
Thank you for your comments and support .
ER605 you can use for PPTP and L2TP server,But it is not having the PPoE server options.
If i have two 800mbps isp what will be combine speed?
Thank you for your comments and support.
In this case you have to use 10gbps loader balancer, then configuration make as aggregation mode you will get 800+800=1600 speed (small fraction will there based on you network switch and interface card ). But the interface should be minimum 2 gbps in router output
Good day how can i set up a multi wan for the same isp subscription,thank you
Thank you for your comments and support🙏.
You required same isp two connection?. You can use same method.
@@abethetechie hi i try dual isp in two the same internet connection but when i speedtest it the result 30-40mbs sometime drops to 25-29mbs my 1 internet speed is 40mbs and my 2nd connection is 40-50mbs i try also use router just to change the IP ADDRESS but still the same can you help how.thank you
You are having same ISP with dual internet . The router will give the features of fail-over or load balancing , it is not having aggregation (means one 10 mbs+20 mbs internet will get 30 mbps that features are not available ) . But this is working based on distribution for example if the internet speed is one 10 mbs other 20 mbs if in the network 3 person are downloading,Based on the load balancing each person will get the 10 mbps speed , Because the 20 mbps split and 10 Mbps will directly allocate as load balancing ( need to set the proper speed in the wan and ratio of the load also ).
@@abethetechie can you guide me how can set up that in my er
1 . Configure 2 ISP on 2 Wan inter face with (ISP router IP should be different )
2. Configure the upload and download speed on on both wan (Based on the ISP speed )
3. Enable load balancing ( no need to use fail over )
4. Set the ratio of the load balancing
Thanks but aggregated up to 2GB is misleading I think. In Multi WAN mode speed is 1/3 of single WAN speed to my testing. Have you tested this and claim and how did you achieve this ?
Thank you for your comments and support.
If you are doing the speed test we are able to see aggregate speed. That wan connection is broadband the speed will not be stable. In downloading a file depends on the latency and download server bandwidth setup. Usual download will be we simply calculate the speed 1/3 even in single connection.