Ich hatte bei einer Schraubstockrestaurierung diesen alten Schleifer in Aktion gesehen und dachte mir schon, dass du ihn dir vornehmen wirst. Tut einfach gut, so detaillierte und gewissenhafte Arbeit zu sehen. Kommt ja leider aus der Mode. Die Kollegen aus dem Werkzeugbau hatte ich schon mit deinen Videos angefixt. 🤣 Die sind bei so etwas ebenfalls sehr genau und lieben auch solch gute Arbeit.
Perfect choice on the paint. I've used that myself. That wire wheel is going to grab those wool-like fabric gloves and pull your hand and fingers right into the bristles. Switch to some leather gloves for wire wheel work.
Bir wilton mengene bir metabo taş motoru bir de bu hayran kaldım. O kadar takip ederim bir almanya bölgesi bir ruslar bir de sen üstad :) Türkiye de senden başka olduğunu zannetmiyorum. Kullandığın makinaların hepsinin bosch pro olması ayrı güzel :)
Bonito de se ver e, de admirar quando algo é bem feito por quem entende P. A. R. A. B. É. N. S que DEUS o abençoe dando muita saúde, iluminando sempre tua mente, dando-te prosperidade e muito e muito sucesso na sua longa caminhada. 👍👏🙏🍀🇧🇷
Greet job. I’m going to restore a metal bandsaw soon and will definitely use the green hammered paint. It has been sitting outside for 45 years. By the way. When you hammer in a bearing, never use the inner race as the face that will receive the blow. Always the outer race.
So...first off, I thought it was a cordless polisher. Nope. Then you can remove the end. Wrench, heat, etc. No go. You send it to its room overnight. Boom. It comes apart. What sorcery is that! I am joking! Love it and an excellent job, as usual. No spiders this time, just lady bugs.
Hallo mein Freund, ein kleiner Tipp von mir, bei einem 3,4,5 adligen Kabel ob flexibel oder nicht immer den grüngelben (Erdung) Kabel etwas länger lassen das beim zug an der klemme immer als letzter der grüngelbe sich lösen sollte wegen der Sicherheit.... war nur ein kleiner tipp
Great job. Love the hammered paint. Was wondering if you made it slightly thinner and did 2-3 coats would it take more abuse. Did you add an "on and off" label or plates?
It's rare to see someone rewind the stator in restoration videos. I rewind them for a living and most people just avoid it like it's taboo to even think about touching it inside.
I seriously doubt that he rewound that himself. I too have worked in or around motor shops my whole life. Shops here won’t rewind fractional HP motors anymore. Just not worth it. He has skills so I guess it’s possible.
I think your comment is valid and probably a good thing. Rewinding a motor is beyond the scope of most home restorers and unless it’s a very special motor it isn’t financially viable to get it done. Most people also realise that doing it wrong on a mains voltage motor could end up with potentially deadly results.
You go to all that effort to get the name plate off and bore down the top rivet so you wont disfigure the plate and then you pry it out of the bottom rivet instead of grinding it all the way down and tear up the name plate and tear apart the edge of the lower rivet hole. Good job... SMH 🤦🏼♂️
Also, can you explain or link how the "Rotor Balancing" works? I understand by watching it how it measures balance, but how does it "correct" imbalances?
You have some serious machinery in your shop. That balancer is awesome. You seem to have the finest file system as well. But why does your drill press sound funky and the stand is so rusty? Looks like mine before I cleaned it up
Thank you for watching. Don't forget to ''Subscribe''
Hello, I'm part of those people who like to see those electrical machine running at the end of the video ! #restoreforlife #Thanx
I will use this machine in the next videos.
*_Like it, you did a perfect restoration_*
Ich hatte bei einer Schraubstockrestaurierung diesen alten Schleifer in Aktion gesehen und dachte mir schon, dass du ihn dir vornehmen wirst. Tut einfach gut, so detaillierte und gewissenhafte Arbeit zu sehen. Kommt ja leider aus der Mode. Die Kollegen aus dem Werkzeugbau hatte ich schon mit deinen Videos angefixt. 🤣 Die sind bei so etwas ebenfalls sehr genau und lieben auch solch gute Arbeit.
Ich freue mich, dass es dir gefallen hat, danke.
@@meinemechaniker , sehr gerne. Du machst nun einmal einen tollen Job.
Did anyone else get the Nutella ad while watching this. 😂 Great restoration.
Turned out very much beautiful and NEW
Bir çalıştırıp test yapsaydın tam olacaktı
Ellerine sağlık👏🏻👏🏻👏🏻
Sonraki tüm videolarda bu polisaj makinasını kullandım. 🙏🏻 ve kullanmaya devam ediyorum.
@@meinemechaniker gördüm tabiki de
mesela bıçak yapınca kesmesini test etmek gibi...
İlgi ile takip ediyorum 😀
@@adige_knife5032 test görüntüleri yanlışlıkla silinmişti 🙏🏻
The color is spot on !!! Excellent work!!!
thanks
Perfect choice on the paint. I've used that myself. That wire wheel is going to grab those wool-like fabric gloves and pull your hand and fingers right into the bristles. Switch to some leather gloves for wire wheel work.
Thank you for your suggestion.
100% agree.
Safety first. Good lookin out Flash Gordon 👍👍
In all fairness you shouldn't wear gloves at all while using any grinder, without gloves you'll only have a cut or burn.
I really enjoy that Hammerite paint.
That old polishing machine was probably state of the art when fIrst built.
Kardeşim müthiş işler çıkartıyorsun özellikle kpss füzesi süperdi. 😂🤣 👍
😉🙏🏻
Good service 👍
👍
nice video
congratulations friend great job
Very nice .
Beatiful 👍
Well worth saving and very handy around the workshop
Thank you
Süper bir dönüşüm, eline sağlık.
Teşekkürler
Love that pulling device.
Awesome restoration! I’ve always liked that blue/green color for some reason.
Thank you. I have plenty of blue and green paint. 😉
Amazing
Love the color
Red Wing is well respected grinder similar to Baldor. It is widely used for dental work. Excellent polishing/grinding machines.
Let it run! Run with the wind!
👍
Nice resto!..always love the hammered paint!
l agree
COOL, WAY COOL!!!
Very well done. 👍👍👍
Thanks 👍
At first I wondered, "Why isn't he using the bench grinder with the buffing wheel to polish the parts?" Then I remembered that he's restoring it, lol.
Good job!
Bir wilton mengene bir metabo taş motoru bir de bu hayran kaldım. O kadar takip ederim bir almanya bölgesi bir ruslar bir de sen üstad :) Türkiye de senden başka olduğunu zannetmiyorum. Kullandığın makinaların hepsinin bosch pro olması ayrı güzel :)
Teşekkür ederim 🙏🏻 benim favorimde yarın sabah yayında olacak 🤚
@@meinemechaniker keşke Samsun'da olsan yanında çırak olarak yarın başlasam 😂
It's cool when you use other restored items (Tools) to restore newer items.
👍
dude...you gotta turn it on! hahaha. nice refurbish
Very good job sir....☺️
Thanks ssr 🙏🏻🌿
Sweet. 👍🏼
👌
A power polisher is a very useful tool. Excellent work giving this one new life!
Thank you 👍
We do not even know if it works or not: no demonstration. Poor form.
Very good 👏🏼👏🏼
Beautiful, I like how you got the colour so close to the original.
Thanks 👍
Yine güzel bir iş. Teşekkür ederim arkadaşım. Daha fazla lütfen
👍 teşekkür ederim
great job👍🏻
Thank you 👍
5:45 that's a nice make-shift cleaner you made with a pipe hose and vacuum cleaner accessory; also get a bench vice preferably gressel :p
gressel is not good vise;) I bought heuer;) because I'm meine mechaniker.
Bravo sana tebrikler
Teşekkürler 👌
Bonito de se ver e, de admirar quando algo é bem feito por quem entende P. A. R. A. B. É. N. S que DEUS o abençoe dando muita saúde, iluminando sempre tua mente, dando-te prosperidade e muito e muito sucesso na sua longa caminhada. 👍👏🙏🍀🇧🇷
🙏🏻🌿 obrigado
Cool RESTORATION👍
Thank you 👍
Excelente !!!
Bon travail ! Je suis stupéfaite par le résultat 😍
working from heart - nice gob - the best
Thanks 👍
Really great job!
thank you 👍
KPSS kitabı en sonunda bir işe yaramış 😀
Başka bir işe yarayacağı yoktu 😉
Güzel restorasyon bu arada , elinize sağlık 👍👏
Teşekkürler 👍🏿
Well done! Excellent restoration. It is very good to have a polishing machine!
Thank you
Belle restauration ;))
Merci
Greet job. I’m going to restore a metal bandsaw soon and will definitely use the green hammered paint. It has been sitting outside for 45 years.
By the way. When you hammer in a bearing, never use the inner race as the face that will receive the blow. Always the outer race.
Thanks 👍
I agree with Rudy Saldivar.
Eline sağlık abi
Teşekkür ederim 👍
Great job mate, came up better than a new one.
Thank you bro 👍
Magnífico trabalho! Assisti com prazer, parabéns e obrigado pelo compartilhar.
Desde o extremo Sul do Brasil, envio um fraternal abraço.
obrigado 👍
You were trying to undo the spindle extension in wrong direction at the first time. Great work
thank you I will consider your suggestions.
👍
congratulations got very good,Mr.David Copperfield's bearings kkk
👍 thanks
This is amazing!
🤙
So...first off, I thought it was a cordless polisher. Nope. Then you can remove the end. Wrench, heat, etc. No go. You send it to its room overnight. Boom. It comes apart. What sorcery is that! I am joking! Love it and an excellent job, as usual. No spiders this time, just lady bugs.
👍
ficou novo e muito funcional amei
Thanks sir
Great job, I don't know what it does.
Thank you Ronald 👍 it is polising machine ✔️
Merica!
👍
Very nice restoration ! I love the polish and the paint, and cheers for replacing the bearings, thank you for sharing.
Thanks 👍
100/100
Harika😊👏🏻👏🏻👏🏻👍🏻
Teşekkürler 👍🇹🇷
Without the marks on the manufacturer's plate, this would look brand new. Nice job. Are you keeping for your shop! Thx for sharing
Great restoration. It would be nice if you tested it so we could see it working.
Thanks, for test you can watch the next video 👍🤗🍀
Hallo mein Freund, ein kleiner Tipp von mir, bei einem 3,4,5 adligen Kabel ob flexibel oder nicht immer den grüngelben (Erdung) Kabel etwas länger lassen das beim zug an der klemme immer als letzter der grüngelbe sich lösen sollte wegen der Sicherheit.... war nur ein kleiner tipp
Danke 🙏🏻🍀
@@meinemechaniker 😊
3-phase? Was looking at the five-conductor plug at the end...
yes 3 phase 👍
Моя есть механерчук! Дас ист фантастиш!
I wanted to see if the ladybug would fall in the hole!!!
Hi bro 👋👋👋 good to see you 🤝🤝🤝very good restoration grinding machine 👍👍👍🔥💣 I watched the video with admiration 👌🏽
Thank you bro 👊
You need to do a restore on your drill press
I did
16:40 KPSS
Great job. Love the hammered paint. Was wondering if you made it slightly thinner and did 2-3 coats would it take more abuse. Did you add an "on and off" label or plates?
It would be wrong to thin it with thinner. It is best to do it once. 🤗
Very good! But a little too dark... plz, put some more lights on. Congrats!
thank you . I was shooting my videos outdoors. now I am working in a closed and more accurate workshop.
You have to turn it on and try it ...cmon its a waste of time watching something build and not seeing it work!!!!!
see all the next videos. you will see that it works.
Garwood NJ is 45 minutes from where I live
It's rare to see someone rewind the stator in restoration videos. I rewind them for a living and most people just avoid it like it's taboo to even think about touching it inside.
I seriously doubt that he rewound that himself. I too have worked in or around motor shops my whole life. Shops here won’t rewind fractional HP motors anymore. Just not worth it. He has skills so I guess it’s possible.
I think your comment is valid and probably a good thing. Rewinding a motor is beyond the scope of most home restorers and unless it’s a very special motor it isn’t financially viable to get it done. Most people also realise that doing it wrong on a mains voltage motor could end up with potentially deadly results.
Never saw it running...?
Abi siz Türkmüsünüz ya ben sizi yabancı sanıyorum zevkle izliyorum emegine saglık
Ne mutlu bana da 👍
Tarih kitabı ele verdi 😂 Güzel restorasyon olmuş. Elinize sağlık.
what kind of can opener do you use ? can you link ? i cannt find it :X
Opener?
@@meinemechaniker 16:55. What are you using a wrench to open can ?
@@adrianrobal5612 first aid scissors 🤗
@@meinemechaniker hooooooly.... Thanks 😅
Show us how it works!
You can see next videos👍
another name for it is a lathe for polishing and grinding
And does it work? What is that for? I missed the final part 🤔 But the rest was nice 👌🏻
Yers Final part is problem but in the next video you can see final part
На 11-26 мы плавно отваливаем, потому что такого балансёра у нас нет(((
👌
ほお、不二越のベアリングを採用しましたね。
はいそうです
This is really beautiful, but does it work?
I use it all the time. look at the next videos, you will see.
That was a great restoration! I am now a subscriber!
👍
So does it work?
if you want to test video, you can check the next videos 👍
Three phase motor ?
Yes theree phase motor 👍
The title says that this a Polish bench grinder but the data plate indicates that it's a Red Wing made in New Jersey. A little help here please?
Could you please copy the title and search for it by typing google.
Rob Wolford It’s a polishing bench grinder, hence the spindle, it’s not Polish as in made in Poland.
@@markharrisllb Sorry. That makes sense.
You go to all that effort to get the name plate off and bore down the top rivet so you wont disfigure the plate and then you pry it out of the bottom rivet instead of grinding it all the way down and tear up the name plate and tear apart the edge of the lower rivet hole. Good job... SMH 🤦🏼♂️
You do it so much better in your videos.
You did the winding put back the motor and then open it again?
yes l do
What brand of hand tools are those? Black with red ?
which tools are you asking?
Also, can you explain or link how the "Rotor Balancing" works? I understand by watching it how it measures balance, but how does it "correct" imbalances?
rotor balancing, just like balancing car tires. even the same.
Всё прекрасно, но не хватает показать работоспособность
👏👏👏👏👏👏👏
👍
You could have ran it. I’d love to have seen it moving.
Pls next videos 🤗
You have some serious machinery in your shop. That balancer is awesome. You seem to have the finest file system as well. But why does your drill press sound funky and the stand is so rusty? Looks like mine before I cleaned it up
If I find time, I will clean that drill.
The Handler Company is still in business making grinders and polishers for the dental and jewelry trades.
🙏👌