Restoration of a 50 year old Huge Rusty Drill Press. Awesome result!
HTML-код
- Опубликовано: 13 сен 2024
- I got this drilling machine for the price of scrap metal. The headstock raise/release mechanism did not work, the headstock lock lever was jammed, the drill chuck was rusty and jammed, the on/off button was missing, all the electrics were rewound with duct tape. BUT the motor worked!
Restoration process.
First of all, I completely disassembled the drilling machine into parts. Some control levers were broken and new ones had to be made on a lathe.
I cleaned the parts of the hull using a paint remover and a rust converter.
I really like to use hammer effect paint on the body parts. Since the case is made of cast iron, it has an uneven surface and it is the hammer effect paint that hides all these irregularities, while the spray paint would only emphasize all the flaws.
During the repair was completely moved the engine. Rust was even on the rotor! Replaced all bearings and painted body.
The bearings on the spindle were also replaced!
In general, the work was not difficult but took a lot of time, and I will be grateful for the "thumbs up" pressed so more people will see the video and I will compensate for the cost of repairing this drilling machine! THANK YOU
I enjoyed working on this project, and upon completion, I had another "helper" in my workshop, who will often appear in the following videos.
So click "subscribe" and be sure to "bell" otherwise RUclips will not notify you about the release of a new video.
Good luck everyone and take care of yourself!
Sincerely, Max!
#awesomerestoration
#drillpress
#restoration
The new identification plates were sent to me late, so they didn't make it into the video. But you can always watch the last post in my RUclips community, I posted a photo of a drilling machine with the plates installed.
Mister, please, always show sandblasting. It is the best part. thanks.
I'll second that (I'm actually the 14th up-vote) not only because everyone loves to see it, but because most of us don't have access to a sandblaster, but dream of one.
What a fantastic job amazing work Thanks for sharing your time and skill 🍺🍺👍👍🇬🇧
Thank you for your comment and high appreciation of my work.
Beautiful restoration job you did restoring that old drill press. It looks much better and it works like a charm too. You worked hard on that machine. Excellent work.
Thank you for your comment and wonderful feedback on my work.
Кажется на этой машине никогда не ставили тиски , раз шины полностью забиты . Рисковые парни на ней работали , ну или у них пальцы новые быстро отрастали 🤣🤣🤣 Работа как всегда екстра класс 🤝👍
Ну уж и патрон бы пропылил 🤦🏻
Красава 👍👍👍
и так сойдет.
Love your work. Thanks!
❤❤❤
Wonderful! i prefer it to a new one!
Absolutely 💯 brilliant ❤
❤❤❤
Добрый день! Узнаю своё родное, советское. Хорошая работа
Сильна была Советская власть, до сих пор техника работает
Is this a re-upload? I could swear I saw this video before. What really nailed it for me was the gear shifter knob.
That's right, you've probably seen this video before on my channel!
I chuckled a bit looking at that handwheel handles. Gear shifts, random threaded rod and a wood...lol
It looks great and you did a wonderful job restoring it as well!!!!
I enjoyed your video so I gave it a Thumbs Up
Thank you for not using tweezers and no dramatic rocking filing!
I see you took lessons from the My Mechanics school of filmography.
У меня почти такой же достался. Стопорный механизм совмещён, тоже готовлюсь к восстановлению. Станины тоже нет., хранился у кого то в гараже и был прикручен прямо к верстаку. Варварство... Придется делать самопальную.
I really like the color choices
No veo que hayas instalado las etiquetas o placas de identidad de fábrica. Ese ligero detalle hace una gran diferencia. Por lo demás, una excelente restauración de la herramienta.
The new identification plates were sent to me late, so they didn't make it into the video. But you can always watch the last post in my RUclips community, I posted a photo of a drilling machine with the plates installed.
двигатель работал - ясное дело, изолента-то синяя
Kryto ❤❤❤😊
👍👍👍
Сразу видно, русские эксплуатировали- синяя изолента и набалдашник с коробки передачи , от ВАЗ 2106
Nice restoration, while not how I might have done some of the work I appreciated the ingenuity you showed in some of your choices.
Really appreciate that you don't put random bad music over your videos
Great job im doing something similar in my garage and youtube chanel good luck.
A nice restoration on an old drill. Far from huge though. I was expecting the opening shot to involve a fork lift.
I hope that crack on the hub of the fan doesn't become a problem if this is a restoration to be used
Everything is fine! The fan feels great!!!😁
It's a drill press, not an Airbus.
It'll be okay.
Не, ну опять дэжавю)) Я просто требую нового. А за работу зачёт. У тебя был другой канал?
Все верно! Это всего лишь дежавю, а не перезалив). По реставрации у меня только этот канал на Ютубе.
Будут новые видео, но немного позже)))
Nice job
Very nice
Excelente trabalho!!
ощущение какого то deja vu
Шикарная приблуда для фрезеровки деревяшек. Работал на таком.
Yeah, much better than a new el cheapo.
Не хватает чего-то , нетлоска или дотошности кдеталям
Parabéns
Отлично!
Beilliant 👏👏
😉👍👍👍
Магнитный пускатель не помешал бы.
A côté de (gex) ain . Jaie trouve un vieux tour des annes 50 ou peut être plus vieux avec les pignon apparents et une tres vielle perceuse a colone tres lourde magnifique pour decorer un garage .mais pour les manutentionner du gros travail
Отпескоструить и полимерной краской бы!!!
Living here in the United States, I can't help wondering: Where does one find and buy old Soviet-era junked machine tools?
in junkyards in Russia, Ukraine, Belarus and all other ex soviet republics
Russian flea market in Riga
У нас таких полно ))
Результат мягко говоря не потрясающий
Как и большинство таких видео - пошкрябал грязь, покрасил и готово. А когда забивал молотком подшипники и тер наждаком колонну - кровь из глаз полилась
What a mess!
А мусор и прочее говно- тяжело убрать или так лучше смотрится?
🎉🎉🎉🎉🎉🎉🎉🎉🎉🎉😂😂😂😂
🙂
Для кого он огромный?!! Настольный!!?
Not much point in degreasing if you then hold the part in your bare hands, just putting greasy fingerprints onto it.
But apart from that 👍
На коллекторе замкнул все пластины наждачкой. Греться будет.
ммм... нет, ничего не греется👍
That is NOT fifty years old! I saw a picture of one on Noah's Ark.
Re-uploaded video
Как называется синяя смазка, подскажите пожалуйста?
к сожалению не могу подсказать... тубе со смазкой уже много лет, и название уже стерлось. Помню лишь что она какая то импортная и вроде высокотемпературная.
@@ITBR_Restoration понял, ну ничего, спасибо и на этом!
@@Destrould Называлась "Фиол", а как сейчас зовется...
old video!😂😂😂😂
Vidéo pitoyable 👎👎👎👎👎
Кайф
👌👌👌