The foundation is pretty much done and now I started working with the logs. The first joint is now ready and it looks like I might have a cabin some day :)
For me, the ideas in ruclips.net/user/postUgkxAfqpMLyFn37qcqUl0FAzqkkycQeXqrhP Plans were a starting point for building different sheds . Ryan gives ideas that allow an individual to draw nicest conclusions into the design and building of his or her own shed.
So far I have started from the first video of this playlist and this project is looking like it was and still is a fun project. I will continue to watch the rest of the playlist as I really want to do this once I get to our forever homestead after our move in a couple years.
Hello form Czeh republic. Hint: If you are not sure, that your cut will be straight on both sides of log, try to start on one side to 1/3 of cut and than cut from oposite side, to watch cut closer to you and maneuver with saw by pulling. With this type of saw, you have no control in push. Only in pull. So do 2nd third of cut and than go back to first stand (side) and finish it. Or turn log to side, do 1cm deep cut and than turn it to another side and do 1cm deep cut as well. It will guide your saw down through cut.
Hei, tosi kiva hirsi mökki. Is there some where I can get the dovetail template? Also the details on how to notchout the top and bottom to fit the logs tight? Kiitos Seanilta
Cool stuff man. I always wondered why the ends of cut lumber was painted. In Philippines we don't build a lot with wood due to the termites and other wood boring pests. Most houses are built with concrete blocks. I did some carpentry when I was younger and I miss the smell of cut wood. Cheers and God Bless. ~Mike and Ester~
@@bernardwalsh9587 Thanks. My logs are about 10x20cm. Here's a pdf where you can get the details: drive.google.com/file/d/1FwVVgtWHW5EQSdNhDSYwBMhtH61eTDFZ/view?usp=sharing
PLEASE...THE TEMPLATE YOU USED TO SCRIBE YOUR JOINTS, WAS IT SOMETHING YOU MADE FROM AN EQUATION ?...I GUESS I AM SAYING, HOW DID YOU FIGURE IT OUT ?...ALSO WHY A FULL DOVETAIL AND NOT A HALF DOVETAIL ?...THANK YOU
Hey. I would also like to know how to measure those joints. Jos tekee vakiokokoisesta höylähirrestä (saunaa) niin se kai olis suhteellisen vaivatonta saada siistiä jälkeä? Ois vain niin kivannäköinen salvos.
Tein sellaisen sapluunan 3d-ohjelmalla tuohon. Se toimi alkuun tosi hyvin. Tein varaukset käsin, ja ainakin minulla kävi niin, että jouduin kuitenkin tekemään varmistusmittauksia vaikka käytin sapluunaa. Aina jostain tuli vähän virhettä ja sitten nurkka ei ollutkaan tiivis. Eli sapluuna kyllä nopeuttaa, mutta käsin joutuu silti tarkistelemaan. Ei niistä nurkista tosin ihan tiiviit tulleet mittaamisen jälkeenkään :)
@@FinnishPlayground alkoiko se varaus muuttua vai mikä tuli. Tuo mallisi näyttää ihan symmetriseltä, mitä taas jotkin versiot eivät ole: päätyneliö näyttää joissakin versioissa epäsymmetriseltä, mikä tekee sen vielä kimurantimmaksi. Rapakon takana joku näytti miten tehdään kehikko-sapluunaa. Mutta ei se ameyrikan malli ole ihan sama myöskään. Täytyy kysellä jostain "perinne" sivustolta? En viitsi alkaa itse etsimään mallia, vaikka se sulka ois kiva saada hattuun. Aluksi yritin tuo palaneen saunan hirsillä hakea: jakaa sisäsivua kolmeen ja ulkosivua 4:ään osaan, jotta siihen jotta siihen pyrstön tyveen tulis tulis sopivaa "vääristymää"... let see.
For me, the ideas in ruclips.net/user/postUgkxAfqpMLyFn37qcqUl0FAzqkkycQeXqrhP Plans were a starting point for building different sheds . Ryan gives ideas that allow an individual to draw nicest conclusions into the design and building of his or her own shed.
So far I have started from the first video of this playlist and this project is looking like it was and still is a fun project. I will continue to watch the rest of the playlist as I really want to do this once I get to our forever homestead after our move in a couple years.
Hello form Czeh republic. Hint: If you are not sure, that your cut will be straight on both sides of log, try to start on one side to 1/3 of cut and than cut from oposite side, to watch cut closer to you and maneuver with saw by pulling. With this type of saw, you have no control in push. Only in pull. So do 2nd third of cut and than go back to first stand (side) and finish it. Or turn log to side, do 1cm deep cut and than turn it to another side and do 1cm deep cut as well. It will guide your saw down through cut.
stavite roubenky? nebo jen hobby?
@@janbrzak1 Už nestavim ze dřeva nic. Stavěl jsem.
@ 2:04, sure wish you had shown how you laid out your template.
Fine dovetail joint! Complicated to carve but very beautiful to look at.
Almost everything in this video is wrong! 😨 Not my property, not my wood, not my future hut ...! 😎 The rest is interesting and nice to watch! 👍😊
Hello from Virginia, USA! I like your work. Could you share how you made your template, please?
Hello from Canada! I see many channels now from Finland....
Hei, tosi kiva hirsi mökki. Is there some where I can get the dovetail template? Also the details on how to notchout the top and bottom to fit the logs tight?
Kiitos Seanilta
I need to go back to the beginning of this. Hello from SW Wisconsin (USA)!!!
i would have made some sawhorses first helps to practice your joint making and then gives a nice working height cheers from australia 🇦🇺
Cool stuff man. I always wondered why the ends of cut lumber was painted. In Philippines we don't build a lot with wood due to the termites and other wood boring pests. Most houses are built with concrete blocks. I did some carpentry when I was younger and I miss the smell of cut wood. Cheers and God Bless. ~Mike and Ester~
Wood is definitely beautiful material. Luckily we don't have termites but don't worry, we have a lot of other irritating bugs :)
@@FinnishPlayground I like your videos. What are the dimensions of your logs? What are the angles and cutting dimensions for your dovetails?
Thx
@@bernardwalsh9587 Thanks. My logs are about 10x20cm. Here's a pdf where you can get the details: drive.google.com/file/d/1FwVVgtWHW5EQSdNhDSYwBMhtH61eTDFZ/view?usp=sharing
Kinda rough on your lumber. How many got cracked from those thrown or dropped off the stack?
Maybe stupid question but, what the TPI of that hand saw?
What did you use to insulate between the logs?
Hello frome SE Ohio USA; AWESOME PROJECT! Where did you get the dovetail template? Thanks
Thanks! Here's a link to the template pdf.
@@FinnishPlayground can you post the template link again
What size is the log home
PLEASE...THE TEMPLATE YOU USED TO SCRIBE YOUR JOINTS, WAS IT SOMETHING YOU MADE FROM AN EQUATION ?...I GUESS I AM SAYING, HOW DID YOU FIGURE IT OUT ?...ALSO WHY A FULL DOVETAIL AND NOT A HALF DOVETAIL ?...THANK YOU
?
It's actually a compound dovetail.
They are harder to cut and the hold water.
He should have stayed with a half dovetail.
👍
Hey. I would also like to know how to measure those joints.
Jos tekee vakiokokoisesta höylähirrestä (saunaa) niin se kai olis suhteellisen vaivatonta saada siistiä jälkeä? Ois vain niin kivannäköinen salvos.
Tein sellaisen sapluunan 3d-ohjelmalla tuohon. Se toimi alkuun tosi hyvin. Tein varaukset käsin, ja ainakin minulla kävi niin, että jouduin kuitenkin tekemään varmistusmittauksia vaikka käytin sapluunaa. Aina jostain tuli vähän virhettä ja sitten nurkka ei ollutkaan tiivis. Eli sapluuna kyllä nopeuttaa, mutta käsin joutuu silti tarkistelemaan. Ei niistä nurkista tosin ihan tiiviit tulleet mittaamisen jälkeenkään :)
@@FinnishPlayground alkoiko se varaus muuttua vai mikä tuli. Tuo mallisi näyttää ihan symmetriseltä, mitä taas jotkin versiot eivät ole: päätyneliö näyttää joissakin versioissa epäsymmetriseltä, mikä tekee sen vielä kimurantimmaksi.
Rapakon takana joku näytti miten tehdään kehikko-sapluunaa. Mutta ei se ameyrikan malli ole ihan sama myöskään.
Täytyy kysellä jostain "perinne" sivustolta? En viitsi alkaa itse etsimään mallia, vaikka se sulka ois kiva saada hattuun. Aluksi yritin tuo palaneen saunan hirsillä hakea: jakaa sisäsivua kolmeen ja ulkosivua 4:ään osaan, jotta siihen jotta siihen pyrstön tyveen tulis tulis sopivaa "vääristymää"... let see.
@@FinnishPlayground Sure wish I could read this.
Да извращенец пилить все вручную . Даже жалко тибя.