HorizonHobby.com How-To: Properly Set Your Gear Mesh

Поделиться
HTML-код
  • Опубликовано: 28 янв 2025

Комментарии • 65

  • @jredmkv8622
    @jredmkv8622 8 лет назад

    This is a great video tutorial for all levels of rc enthusiasts. The paper test is my favorite method.

  • @maxxpacks
    @maxxpacks 3 года назад

    ANOTHER GREAT VIDEO FROM THE TRACKSIDE RACING GURU...

  • @ChuckCLJ
    @ChuckCLJ 10 лет назад +4

    Great video. I just have one small critique. I would have shown the viewers how to check the mesh at at least 4 quadrants of the spur geae. In my experience, very few spur gears have zero run out. This means that there will usually be a section of the gear where the mesh will tighten up. It's a good idea to make sure you don't have a tight spot.

    • @Turbogramps
      @Turbogramps 10 лет назад

      That's what I did when I raced RC cars. I would check the mesh all around, because spur gears are not always perfectly round. Other than that Good Video.

    • @horizonhobby
      @horizonhobby  10 лет назад

      Turbogramps I guess I haven't had those sorts of issues with the TLR spur gears. I pretty much set and forget because, honestly, if my mesh is set right it will accommodate any "untrueness" or the gear being out-of-round.

  • @adamhudson6812
    @adamhudson6812 8 лет назад

    Always nice to have a refresher course!

  • @mrmidnight32
    @mrmidnight32 3 года назад

    What about the bolt tension on the spring that’s on the drive shaft of that spur (silver spring in this video)
    My I can’t find anything on adjusting this or what it actually does or how to tune it properly.

  • @Klownenation
    @Klownenation 8 лет назад

    That is cool. I never actually put the paper in between as I always thought you started the paper into the mesh and gave it a pull. If the paper tore it was too tight.

  • @Hellonwheels163
    @Hellonwheels163 7 лет назад

    Should I have to reset the gear mesh on a rtr ecx ruckus to keep the motor/esc from overheating before my 1800mah 2s Lipo battery dies?

  • @InTheDogHouse3DPrinting
    @InTheDogHouse3DPrinting 8 лет назад

    Great tutorial, I always had issues getting the pitch set on my Nitro trucks. Does this hold true to metal gears as well?

  • @TOMMYTOM78
    @TOMMYTOM78 6 лет назад

    Do you use lock tight for final assembly? I just took my motor out of my cen colossus xt and it looked like there was some lock tight red on the screws. Every vid I've watched on setting the gear mesh doesn't look like anybody is using lock tight.

  • @ericcrownover5656
    @ericcrownover5656 8 лет назад

    Very useful information! Getting back up to speed after being out of the RC game a while.

  • @dewaynepayne6500
    @dewaynepayne6500 9 лет назад

    I have a losi ten t nytro.having problems out of the r.o.s.s. starter keep stripping gears. Would like to put in pull start motor in.is that possible ?

  • @andrewmurphy8724
    @andrewmurphy8724 8 лет назад

    Great video for beginners. Great info for veterans also.

  • @rdminitrucker22
    @rdminitrucker22 8 лет назад

    Love the how to's you guys post.

  • @KMLifeadventure
    @KMLifeadventure 8 лет назад

    Can you do a steering servo setup with the transmitter setup

  • @ToneGallis
    @ToneGallis 8 лет назад

    Solid basic info here. Excellent

  • @brianskellenger9620
    @brianskellenger9620 8 лет назад

    Great tip for beginners.

  • @gavinjames-dues6815
    @gavinjames-dues6815 9 лет назад

    I have a Question would you need to get a different spur gear for a 3.5T motor

    • @horizonhobby
      @horizonhobby  9 лет назад

      Gavin James-Dues Spur, it tepends, pinion, most definitely. Often it will be easier to get the correct gear ratio by going to a larger spur gear.

    • @gavinjames-dues6815
      @gavinjames-dues6815 9 лет назад

      OK thank you

    • @gavinjames-dues6815
      @gavinjames-dues6815 9 лет назад

      Do you know what gears I would need for a 3.5T motor

  • @wallacedouglas2840
    @wallacedouglas2840 5 лет назад

    What is your dislike against thread lock on pinion gear grub screw?

  • @Rowdy216
    @Rowdy216 8 лет назад

    Really informative. I'm not a fan of the paper method, but it's still a good video.

  • @vicentevalerio1454
    @vicentevalerio1454 8 лет назад

    Great video. Thanks

  • @joebastiaanse4251
    @joebastiaanse4251 8 лет назад

    Nice, good info

  • @davidravert9639
    @davidravert9639 8 лет назад

    useful info. thanks

  • @louissatosan8525
    @louissatosan8525 8 лет назад

    Great How to!

  • @gcoopertrollope5672
    @gcoopertrollope5672 8 лет назад

    Trying to rebuild my rear diff on me hpi! This helps alot!!

  • @gunthergretz672
    @gunthergretz672 8 лет назад

    very useful tip!

  • @ATC235
    @ATC235 8 лет назад

    Great video

  • @robertking11
    @robertking11 8 лет назад

    Good info

  • @briannagy3445
    @briannagy3445 8 лет назад

    good vid

  • @travisferry4784
    @travisferry4784 8 лет назад

    Thx for the info!

  • @tattoojohn4
    @tattoojohn4 8 лет назад

    Great tip!

  • @MrScottyFoy
    @MrScottyFoy 8 лет назад

    A trick I've used for many years!

  • @andrewpokorney7522
    @andrewpokorney7522 8 лет назад

    good info

  • @kevinwilliams2912
    @kevinwilliams2912 8 лет назад

    Very informative

  • @jakedelrie4052
    @jakedelrie4052 7 лет назад

    Thank you

  • @richardschott4099
    @richardschott4099 8 лет назад

    Good stuff to know

  • @mattkidd3652
    @mattkidd3652 8 лет назад

    Very useful!

  • @loganreimer722
    @loganreimer722 8 лет назад

    Very helpful.

  • @bsharp8209
    @bsharp8209 8 лет назад

    very informative

  • @benweibel1357
    @benweibel1357 8 лет назад

    Thanks

  • @MrDragknee
    @MrDragknee 8 лет назад

    good to know!

  • @betheleskimo9680
    @betheleskimo9680 8 лет назад

    I've always liked to have my mesh set just right for longevity and smoothness

  • @walterproulx9326
    @walterproulx9326 8 лет назад

    Good for beginner

  • @DebonairOnline
    @DebonairOnline 8 лет назад

    A good old school trick.

  • @MrHottStick
    @MrHottStick 8 лет назад

    Yeehaw Baby!

  • @CookingWithJaysin
    @CookingWithJaysin 8 лет назад

    Nice

  • @EricCarter99
    @EricCarter99 8 лет назад

    this helped

  • @mellowraccoon6419
    @mellowraccoon6419 8 лет назад

    Gotta do the paper thing

  • @chrismatlack780
    @chrismatlack780 8 лет назад

    nice

  • @paulconner6
    @paulconner6 8 лет назад

    👍

  • @kewlbug
    @kewlbug 8 лет назад

    oh yeah

  • @mattkidd3652
    @mattkidd3652 8 лет назад

    Boom!!

  • @harleyknall
    @harleyknall 8 лет назад

    opinions

  • @sheltondavidson153
    @sheltondavidson153 8 лет назад

    Been using paper to set mesh since 1994. You'd think I could just eyeball it by now.

  • @bmainard
    @bmainard 8 лет назад

    basic

  • @bradbozarth1822
    @bradbozarth1822 5 лет назад

    Ok so this is basically common sense?

  • @andremcnaught7545
    @andremcnaught7545 8 лет назад

    Great video

  • @andremcnaught7545
    @andremcnaught7545 8 лет назад

    great info

  • @johnsanfilippo4493
    @johnsanfilippo4493 8 лет назад

    Very informative

  • @jackplique1949
    @jackplique1949 8 лет назад

    Very helpful