Best video on RUclips about the subject tbh. Thanks bro! I tried today ok my car (Citroen ZX) before watching your video because I thought It would be similar to Pug 206, but its not... Now I know how thanks to you and will attempt again, thanks man
Fuck me dead, when I saw the finished product....I've lowered a Berlingo using the full (proper) method but only to match some coilovers, nothing like the slammage on this bad boy.
Um dia antes de mexer eu lavo tudo com lava jato. Passo spray desingripante onde tem que mexer. Separo as ferramentas e faço um roteiro dos serviços. Funciona bem, vira um festa mexer. Para isso olhar vídeos como este antes é fundamental. Obrigado irmão, por seu vídeo.
I presume there's no issues with raising the back end in the same way? Running 17's on my Ph1, combined with carrying a reasonable bit of weight, means I need to do something about the rubbing.
My ARB plate bolts get them selfs unscrewed every month. I've tried threadlocker (instabond 104 and loctite 2??-blue one) but it works until the car is under load, if there is someone in the rear seats or something in the trunk. My wheels dont have negative camber and font rub inner arches, but there is some slight move when I push the wheel on 12 and 6 o'clock. Its been rebuild but I dont know what do to with ARB bolts and is it because of knackered axle ?!?
Hello I am from Trinidad and not much people can fix this car. But I am getting some kind of noise to the back right side of the car especially when the sun is hot when it rain you don't hear much of the nice. Any suggestion where to start looking in the back for this defect.. thank you for any help...
Deve desmontar a suspensão traseira. Sobre isso tem vídeos no RUclips. Depois retificar ou trocar o eixo e o rolamento. Em alguns casos só colocam uma bucha de nylon no lugar do rolamento sem mexer no eixo. Deve engraxar bem. Abrir a cada dois anos e engraxar de novo. Pode e deve se puder por uma válvula graxeira (limite) no eixo e engraxar de vez em quando. Aí fica show.
Best video on RUclips about the subject tbh. Thanks bro! I tried today ok my car (Citroen ZX) before watching your video because I thought It would be similar to Pug 206, but its not... Now I know how thanks to you and will attempt again, thanks man
Aw mate it’s good to hear!
Fuck me dead, when I saw the finished product....I've lowered a Berlingo using the full (proper) method but only to match some coilovers, nothing like the slammage on this bad boy.
Um dia antes de mexer eu lavo tudo com lava jato. Passo spray desingripante onde tem que mexer. Separo as ferramentas e faço um roteiro dos serviços. Funciona bem, vira um festa mexer.
Para isso olhar vídeos como este antes é fundamental. Obrigado irmão, por seu vídeo.
I presume there's no issues with raising the back end in the same way? Running 17's on my Ph1, combined with carrying a reasonable bit of weight, means I need to do something about the rubbing.
I'm 100% here for more 306 content! Also, what you running in front to get that low?
Hello mate! Thanks for the nice comment I’ve got big stuff in the pipeline. Had Raceland coilovers for a 206 up front 👍
Look forward too it all! I've got some big plans for my 306 too! Roll on summer shows!
Can you lower it by just replacing the rear shocks for lowering ones? Or is it necessary to adjust the torsion bar
the shocks only take the bounce out of the ride not weight baring so shocks make no diffrance to height
Thanks for sharing 💪🏼👍🏼
How did you lower the front part??
Do the flatheads need to come out where the 13mm bolts are?
My ARB plate bolts get them selfs unscrewed every month. I've tried threadlocker (instabond 104 and loctite 2??-blue one) but it works until the car is under load, if there is someone in the rear seats or something in the trunk. My wheels dont have negative camber and font rub inner arches, but there is some slight move when I push the wheel on 12 and 6 o'clock. Its been rebuild but I dont know what do to with ARB bolts and is it because of knackered axle ?!?
Hello I am from Trinidad and not much people can fix this car. But I am getting some kind of noise to the back right side of the car especially when the sun is hot when it rain you don't hear much of the nice. Any suggestion where to start looking in the back for this defect.. thank you for any help...
Deve desmontar a suspensão traseira. Sobre isso tem vídeos no RUclips.
Depois retificar ou trocar o eixo e o rolamento. Em alguns casos só colocam uma bucha de nylon no lugar do rolamento sem mexer no eixo.
Deve engraxar bem. Abrir a cada dois anos e engraxar de novo.
Pode e deve se puder por uma válvula graxeira (limite) no eixo e engraxar de vez em quando. Aí fica show.
Make more videos on the 306 please lol.
Trying this on my 206, having trouble hammering the arms out. How hard should it be to get it out? Or maybe im doing something wrong?
Having same problem you get sorted?
Please make more peugeot 306 content
do you take the shocks out?
What type size are you running
Hi lad good video is she lowered 4 nicks
Lad where is your xud rebuild video!
Inappropriate f words, for my daughter showing at school
?
De que
Do Peugeot 306.