Honda CFR250X Carburetor removal | DIY Repair | FULL Disassemble and Reassemble
HTML-код
- Опубликовано: 29 июн 2021
- This video is to demonstrate how to access and remove the carburetor on a 2012 Honda CRF250X.
This job would be the same for the following years and models
2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2014, 2015, 2016, 2017, 2018, 2019
CRF250R, CRF, 250R, 450R, 450x CRF450X, CRF450R,
Amazon Link
All Balls Carburetor Repair Kit 26-1476 Honda CRF250X 2008-2015
amzn.to/3AP3YCk Хобби
Bikes sat too long in my box trailer! Bad gas and wont start!! What a pain to remove these carbs!!!
Thank you for taking the time to show people the proper way to remove and replace these carbs!!
dont need to do that mate just take out bottom bolts and losen the top it will lift up then tighten the top ones the half frame will stay in place ,when ya done losen the screws drop it back down put bottom bolts in ..ya dont need to take full frame off just take bottom nuts out and losen top ones and lift it then tighten to hold in place while you work,the frame will hold in place lifted up
Is there a video on this?
Yes look into smog delete or rejetting vids.
Hugley helpful thank you for all the detail. It was my first time doing the carb and I wouldn't have gotten too far without this video.
Helped a lot ! Seemed to easy to get out with the video! Thanks
Thank you for the vid! Hope I can get the air boot on tomorrow!
Looks like a nice little project I got into
Great video. thanks for the help.
Just got done pulling mine man what was Hondas engineers thinking.
This is so helpful. It deserves way more view and likes. Thanks for doing this. I subscribed just to support your channel whatever else you cover.
Quality video. Just wish it wasn’t sped up so much because some parts were hard to see as it is.
I am trying to do this on my bike now and I've gotten almost to the part where i can remove the carb. I cannot figure out how to remove the throttle linkage from the carb though, its a circle with cables on the top and bottom of it which rotates when the throttle is twisted. Probably the same as the one in the video. How do I take these off?
Hello there, question for you since you are well versed in Honda CRF’s. I have a 04 that idles fine and sitting it will throttle up fine however when I kick it in gear and try to take off it will bog down really bad and almost shut off. I checked the accelerator diaphragm which seems ok, any suggestions on what to check next? Thanks 🙏, great videos btw they are a huge help.
Hi, do you know what size are the vent hoses that come out of the carb? Is it 3mm or 4mm? Thanks,
Thank you! I just bought a Honda 2001 cr250r and it had bad gas so I cleaned out the tank and removed the plastic too and, it was a bitch to remove the carb. Thanks man
Great video just bought an 06 250x qnd it's dumping gas as soon as the gas is turned on
Needle and seat is stuck. Tap the carb with a screw driver and it might stop the leak
Good lord. Step 1.) disassemble 75% of bike. Step 2.) remove carburetor.
Noticing this myself.....just paid a shop$400 to clean carb tank fuel filter etc......still not running right asked them if they disassembled the bike to get it out kid who did work happened to be right there and was like no we just flushed it out! I am so pissed bout to just do it myself this way 😡😩
@@sebertspestsolutions - That is appalling. But yeah, I'm going to try that at home first. Drown it in Sea Foam and see if I can get 'er goin'.
а я думал у меня трудно снять)))
I’m having trouble putting the throttle cables back on
Good luck. It’s an absolute disaster putting them on. I’d recommend that you stop. Wait a bit until you have the patience to do it again. And use the smallest wrenches you can to try and get the the cables back on.
I can’t even get them off
Engineering…”but you’ll have to remove everything to get to the carb…No they’ll have to” Problem solved.
This is insanity