Very good explanation, you can say specific information in English of 3mm, 11mm...like that so that it will be helpful for the people like me who can understand little Hindi. Thx for efforts. Wish you and family a happy deepavali and.to all viewers.
I have planned to construct two separate rooms like 20*10 ( ground floor with 10*14 room size at first floor) & 22.5*10 (only ground floor) . My engineer suggested RCC is as follows. Pls tell it correct or not. Basement level of 22.5*10 is 2 feet less than 20*10 room 1. For 20*10 - 6 columns of 12*4 with 8mm stirr up of 7 inch c/c - four at each corner and remaining two at spacing of 8 feet at one end and 11 ft at other end. Plinth beam with 1.5 feet height and 9*9 (l*b). Ceiling height is 10 feet. Planned tie beam at below windows (2.5 feet) and lintel (7 feet) of 6 inch rcc 2. For 22.5*10 - 6 columns of 12*4 with 8mm stirr up of 7 inch c/c - four at each corner and remaining two at spacing of 10 feet at one end and 10 ft at other end. Plinth beam with 1 feet height and 9*9 (l*b). Ceiling height is 12 feet. Planned tie beam at below windows (4 feet) and lintel ( 8 feet) with 6 inch rcc And join the both room in ceiling and both room in 90 degree position to each other
Bhai ek personal question h?? Mera २००gaj ka plot h... Usme piller banwaye the vo ground level tak cast kr k chod diye the... Due to some problem kaam band ho gya. Ab plot me jo b pillar bar the, sab casting height se hi fully bend ho gye h.. Ab pir se kaam start krna h toh piller making k liye kya krna chahiye?? Suggestion bar k liye chahiye ki unko lapping kr k seedha kkr k cast kre ya cut kr k cuppler lagaye??? 3storey building banani h toh base pillar strong rhe, uske liye kya kya option ho skte h???
Agar 1st floor ke liye colan ki sariya slab ko match krti hai to usko joint krke colan kaise khade kare ispar vidio banaiye sir 🙏🙏 aapke video bahot acche hote hai
Bhai sahab lapping apne tension zone par kiya hua hai jo ki bending zone me aana hota hai mid of the floor length par ...big mistak changes of structural failure ...and rings bend bhi ni hai jo ki 135 ° par muda hona chahiye for earth quake resistance and load bearing and spacing btw stirrups is also not more than 175 mm and also lapping bar length should not be similar ...if main bar bada length ka hai so distribution ussse 6-8 inches kam hone chahiye ese hi har ek bar me
Sir ek steel bar ki length 39.6 feet hoti hai. Tho kyu hum jitne height rkni ghar ki utni steel bar nhi rkte aur sariya kat dete hai hmare tekedar ne bi aisa hi kiya. Aur fir lapping krege bolra. Tho isse tho steel ki strength tho ktm hogyi na. Plz btaye sir🙏🙏
Sir my house is constructing in dehradun (Uttarakhand) in area of 2200 square feet.our arcitech made the map but not by structure design. So our contractor structure engineer has given 20 columns. Of size 9×14.In 1 column he is using 6 steel bars, 4 steel bar of 16 mm and 2 steel bars of 12 mm.footing is taperzoid with height 1.5 feet and he is giving 9×18 plinth beam size. in outer he is using 8 steel bars 4 steel bars of 16 mm and 4 steel bars of 12 mm. But in only 2 of column there is span of 18 feet. And he is saying that without any tension you can make G+2 in this structure. Do I have to worry aur tension free. Plz guide me sir🙏🙏🙏🙏🙏
Sir mere Ghar Mei total 20 columns use hua hai , ek column pe four 16mm rod hai bas, kitne floor Tak upar jayega Ghar?? Aur abhi bas ground floor bana hai, 11 saal ho Chuka hai aur first floor bana nahi Kya isse column ka base weak hoga ?? Upar ke terrace se Column rise sirf 3 inches hai ,iske baare Mei Kya kehna hai ??
Sir mere total ghar k construction m 20 column h aur bs 2 column m h 18 feet ka distance baki h column m. 10 ft, 12 feet tk h. Aur column 9×14 ke h. Aur steel bar 6 h. 16 mm ke 4 aur 12 mm ke 2.tho sir m G+2 bna skta hu. Plz guide sir🙏🙏🙏
Hi, can 6 inch by 15 inch column size be enough for 3 storey building where soil is hard ? How many maximum floors we should construct with this size ?
@@srinupantagolusula2242 For the 3 story rcc construction 16mm rods often used. But minimum bars shouldn't be less than 6 pice. And the depth of the footing shouldn't be less than 4 feet.
Please reply must, is it okay or not if not then please share with me you idea if i build and frame structure hose (G+1) external columns size is 9" x 12" steel bar 4# 16mm outer side & 2# 12mm inner side internal columns size is 9" x 21" steel bar 4# 16mm outer side & 4# 12mm inner side beam size is 9" x 15" top 2# 16mm bottom 2# 12mm top extra bar 2 14mm (L/4) bottom 2 14mm (L/3) space between two columns external side is 4.5 meter space between two columns from external to internal side is 6.4 meter
@@sanjeevsah3973 I think it would be a bit risky. But you can use steel roof instead of concrete slab. And it will bring a good design as well as safe over the slab from rain and UV rays. Moreover, it will be kept cool inside the house.
@@Life_is_Awesome_CivilI hired a contractor to build my house last 6 months ago, they used only 6 pieces 12mm steel bars from ground floor, the size of columns is 12×12". I'm planning to add second floor but I have no idea is it safe or not,
@@Life_is_Awesome_Civil Im follower off yours & your explanation is to good nd clear Stiil im bit confused about m sand Our Engg said using m sand is safe for whole work except finishing (GILAAWA)? Waiting for your reply What is disadvantages nd what is advantages. Thanks for your Support From ksa But im from Karnataka hubli Th
Hii sir mera plan 15x59 hai mai usme g+3 banana chayta hu pls ap bataogy ki colunm size aur bar size kya hoga aur beam size n bar size kya hoga pls tel me
Aap bahut achchi details men samjhate ho
Very good explanation, you can say specific information in English of 3mm, 11mm...like that so that it will be helpful for the people like me who can understand little Hindi. Thx for efforts. Wish you and family a happy deepavali and.to all viewers.
Thank you, I will
Please use English also even for the sizes of bars and spacing.thatll be more effective.wishes from Sri lanka
I have planned to construct two separate rooms like 20*10 ( ground floor with 10*14 room size at first floor) & 22.5*10 (only ground floor) . My engineer suggested RCC is as follows. Pls tell it correct or not. Basement level of 22.5*10 is 2 feet less than 20*10 room
1. For 20*10 - 6 columns of 12*4 with 8mm stirr up of 7 inch c/c - four at each corner and remaining two at spacing of 8 feet at one end and 11 ft at other end. Plinth beam with 1.5 feet height and 9*9 (l*b). Ceiling height is 10 feet. Planned tie beam at below windows (2.5 feet) and lintel (7 feet) of 6 inch rcc
2. For 22.5*10 - 6 columns of 12*4 with 8mm stirr up of 7 inch c/c - four at each corner and remaining two at spacing of 10 feet at one end and 10 ft at other end. Plinth beam with 1 feet height and 9*9 (l*b). Ceiling height is 12 feet. Planned tie beam at below windows (4 feet) and lintel ( 8 feet) with 6 inch rcc
And join the both room in ceiling and both room in 90 degree position to each other
Bhai ek personal question h??
Mera २००gaj ka plot h... Usme piller banwaye the vo ground level tak cast kr k chod diye the... Due to some problem kaam band ho gya. Ab plot me jo b pillar bar the, sab casting height se hi fully bend ho gye h.. Ab pir se kaam start krna h toh piller making k liye kya krna chahiye??
Suggestion bar k liye chahiye ki unko lapping kr k seedha kkr k cast kre ya cut kr k cuppler lagaye???
3storey building banani h toh base pillar strong rhe, uske liye kya kya option ho skte h???
Aap bahut achhe se samjhate hain
Is it safe to use only 4nos of 16mm steel bar on 3 storey building,? Sir, Please give me suggestion
I also want to know that
Nope.. actually if you have money you can add more for future purposes also.
What if we built G+2 and pent house with 6 no of 12mm rods? Column to column max distance is 15ft, min dist 10 ft!
Agar 1st floor ke liye colan ki sariya slab ko match krti hai to usko joint krke colan kaise khade kare ispar vidio banaiye sir 🙏🙏 aapke video bahot acche hote hai
Bhai sahab lapping apne tension zone par kiya hua hai jo ki bending zone me aana hota hai mid of the floor length par ...big mistak changes of structural failure ...and rings bend bhi ni hai jo ki 135 ° par muda hona chahiye for earth quake resistance and load bearing and spacing btw stirrups is also not more than 175 mm and also lapping bar length should not be similar ...if main bar bada length ka hai so distribution ussse 6-8 inches kam hone chahiye ese hi har ek bar me
12mm ke 6 baar dene se kitna floor Tak building Ko banaya ja sakta hai
Sir ek steel bar ki length 39.6 feet hoti hai. Tho kyu hum jitne height rkni ghar ki utni steel bar nhi rkte aur sariya kat dete hai hmare tekedar ne bi aisa hi kiya. Aur fir lapping krege bolra. Tho isse tho steel ki strength tho ktm hogyi na. Plz btaye sir🙏🙏
Sir my house is constructing in dehradun (Uttarakhand) in area of 2200 square feet.our arcitech made the map but not by structure design. So our contractor structure engineer has given 20 columns. Of size 9×14.In 1 column he is using 6 steel bars, 4 steel bar of 16 mm and 2 steel bars of 12 mm.footing is taperzoid with height 1.5 feet and he is giving 9×18 plinth beam size. in outer he is using 8 steel bars 4 steel bars of 16 mm and 4 steel bars of 12 mm. But in only 2 of column there is span of 18 feet. And he is saying that without any tension you can make G+2 in this structure. Do I have to worry aur tension free. Plz guide me sir🙏🙏🙏🙏🙏
Apka vedio bahut achcha rahta hai
Sir hmara tekedar bolra ki joggle nhi hoga wo jo lapping krega sida badega sariya. Ye shi h ya glt
Sir mere Ghar Mei total 20 columns use hua hai , ek column pe four 16mm rod hai bas, kitne floor Tak upar jayega Ghar?? Aur abhi bas ground floor bana hai, 11 saal ho Chuka hai aur first floor bana nahi Kya isse column ka base weak hoga ?? Upar ke terrace se Column rise sirf 3 inches hai ,iske baare Mei Kya kehna hai ??
My RCc column size is 10 by 12 inch can I construct G+3 building. Steel used 16mm 4nos and 12mm 2nos. Pls reply
Laging galt hai kya ?
Rings ko end point pr bend kiya jata h,lock krne k liye,for better reinforcement,jise aaj kal k masons nhi krte h
6"x18" colume size , bar 12mmx8no.
Colume to colume distance 12feet.
To kitna manjil bana sakte he?????
Sir mere total ghar k construction m 20 column h aur bs 2 column m h 18 feet ka distance baki h column m. 10 ft, 12 feet tk h. Aur column 9×14 ke h. Aur steel bar 6 h. 16 mm ke 4 aur 12 mm ke 2.tho sir m G+2 bna skta hu. Plz guide sir🙏🙏🙏
I have used 9*12 column will it create problem
Hi, can 6 inch by 15 inch column size be enough for 3 storey building where soil is hard ? How many maximum floors we should construct with this size ?
Lapping are bad ,it should be done alternately, also observe the 135 degrees for lateral ties. RCC joints should be tied properly. Thanks
Brother..four 20 mm with 2d16mm bars how many story it can go..wid extra c ring to support d16..
3 floors
Thanx
@@Life_is_Awesome_Civil bro 3storyd bulding 16 mm rods use okna
@@srinupantagolusula2242 For the 3 story rcc construction 16mm rods often used. But minimum bars shouldn't be less than 6 pice. And the depth of the footing shouldn't be less than 4 feet.
11 into 12 room size ko 15 inch ke colum me 12 mm ka 6 sareya yous kiya hai easse 2 floor home banega kya sr
Hi..Any idea on the cost of 9×12 for 2000 sqft home.
Just a guess will work.
Can a house for 3 floor can be made by 8in and 14 in colum
Sir 6 colum se banye hue ghar per last kitne floors banasakty hain.. Please batyen..
Please reply must, is it okay or not if not then please share with me you idea
if i build and frame structure hose (G+1)
external columns size is 9" x 12" steel bar 4# 16mm outer side & 2# 12mm inner side
internal columns size is 9" x 21" steel bar 4# 16mm outer side & 4# 12mm inner side
beam size is 9" x 15" top 2# 16mm bottom 2# 12mm top extra bar 2 14mm (L/4) bottom 2 14mm (L/3)
space between two columns external side is 4.5 meter
space between two columns from external to internal side is 6.4 meter
Can we use 4 16mm rod and 4 12mm rod for g+4 rcc house?
4 16mm plus 6 12mm in dual lateral ties @ 12x16 inches concrete cast maybe for sure
Sir my cullm size 14x9
Which size bar required
2 floors building =four 12mm + two 10 mm is fine or not bro?
Yeah it's enough specially u can construct two storey for min of 8 by 8 inch coloum with 16mm of four pieces also
Two floors means ground-floor + first + secound floor , otherwise ground floor + first floor.
Great sir ...sir cn I make 3 storey building with 12 mm rod with 6 rod in each coloum
Use 4 pieces of 16 mm rods along with 2 pieces of 12 mm
@@Kk-yi6hk sir the prblm is tha i have already made G+1.. So now I wanted to have another floor on top.... So cn i do it Or not
@@sanjeevsah3973 I think it would be a bit risky. But you can use steel roof instead of concrete slab. And it will bring a good design as well as safe over the slab from rain and UV rays. Moreover, it will be kept cool inside the house.
@@Kk-yi6hk surely sir... I will do as u have suggested me
Is it safe to use 6 pieces of 12mm steelbars for columns, for 2 storey house???
Yes but use 16 mm and 12 mm
@@Life_is_Awesome_CivilI hired a contractor to build my house last 6 months ago, they used only 6 pieces 12mm steel bars from ground floor, the size of columns is 12×12". I'm planning to add second floor but I have no idea is it safe or not,
Is it C1 or C2 column ?
Sir maine same use kiya hai aise hai but bich me 12 mm ke jagha 16mm hai.
Means 6p.16mm hai..
Column size ke hisab se position and facing ka ek vdo banaeye
Is video me column ka distance kitna h
Sir, teen manjila gharka ek column ka cost Kitna ata hai? Bataye please.
1400 sqf huose k liye kitna greynight lagega.... Windows and doors ki chuokhat ko.... Kitna price hoga
Depend on quality
Okk.... Phir bhi ap cost bataye plz kam me kam
Very good english
Sir, what is the size, thickness and depth of footing for slab 2 storey house for 72 square meter..thanks!
U doing good job bt u have to use some English word in between like column size 9ft and 12ft like this
Really very nice thenk.s
Agar description mea b details likh detein tho bohot achcha rahta taki video aur tik se samaj jatein
Hello sir 40×45 men groud flor men pura shop banana hai usmen kinta pillar ayega aur pillar dpc se kitna fit andar pillar hona chahiye pls sir bataye
10inch colam se 3floor ban sakta hai
10mm ka chhariya hai
What is formula of crank and bending Column?
Centre to center distance kitna hai column ka yaha pe ?
Bhai ek ques e y new sriye or bad m lgae hue sriye k beach gap rkhna jruri h kyunki hm log bna re h to isme gap ni rkhvaya bilkul b
No gap
Hm
First floor column marking starter or pedestrial marking kaise kare?
Sir app ka
plan both ache hota hai our her plan me app bout demag lgate hi her chies me aur colour me bhi bulding ka 35"50 ka plan do north said said
5 floor ki column size kitna hai, plz batadijiye.
16mm
Use 20 mm bars along with 16 mm and the footing depth should be more than 5 feet.
Maximum span between two columns if columns size is 10"×15"
G+3 ya G2 ka hai coulam
G-2 ka colom size & street nose kitna plz tell me
16 mm ki jagah 12 mm use kr sakta hai kya..?
If you are going to built a house more than one story then you should consider 16 mm bars of 4 along with 2 pice of 12 mm .
Hi sir
Is thier M sand is safe for foundation work
Yes
@@Life_is_Awesome_Civil
Im follower off yours & your explanation is to good nd clear
Stiil im bit confused about m sand
Our Engg said using m sand is safe for whole work except finishing (GILAAWA)?
Waiting for your reply
What is disadvantages nd what is advantages.
Thanks for your
Support
From ksa
But im from Karnataka hubli
Th
Hii sir mera plan 15x59 hai mai usme g+3 banana chayta hu pls ap bataogy ki colunm size aur bar size kya hoga aur beam size n bar size kya hoga pls tel me
Ya apka email add mil sakta hai kya to mai apna plan apko send karu pls help me
Bahot urgent hai pls
Hmara 2200 square feet m bnra house. 20 column tik h 9×14 ke
Slab thickness kitna hai???
5 inch
Load bearni kiya kuchh problem hai kay
Column nahi karna
Concrete dalte wqth vibrator use karne main advantage our disadvantage bataiye sir
Nice
sr thanks for this video sr how can we do ceep hous 20 × 16 FOR RENTAL
Sir lintel ma Kitna din Pani bare
Awesome
Stirrups has to bend 135 degrees thats wrong design
U have constructed 4 16mm and 2 12.mm
Overlapping of bars should be at alternate
You are right bro
Thank you sir
Amazing
Colum distance
Bhaiya new home ka walkthrough dalo
Double bars lene ki koi zaroorat nhi hoti h,ye masonry diffect h
nice,can you teachme?
Low voice
13×33 HOUSE plan
Your colum leaping are to much bad and are all ring binding also losses how you are say this works are good 😇😇😇????
Plinth beam bar details videos send me please bar details in speak English
Nice sir ji
what is size of the rod
bad lapping ,bad work
Bhai 2 story building me colom nhi hai.colom kaise lagaye video banado
Hello sir
jab tumko pata nahi hai to kyu video banaraha hai bhai???
Mei 6no 12mm rod dalke 3floor uthaya
Ok thanku
Column kaa size kya lia tha ??
9 column 9×12 3colmn 9×15