PAUT SETUP AND CALIBRATION ON MX2.

In this video, we had demonstrated Omniscan MX2 operation from making the setup till calibration for PAUT (Phase array ultrasonic testing). In this one video we had covered how to make the setup, velocity calibration, wedge delay calibration, sensitivity calibration and TCG.
This video is for them, who are new in the field or looking at the equipment first time. This video will help them to get use to with the equipment.

[@ulia7521]

Really helpful for beginners to understand paut calibration, great job brother 👏

[@ndtsolutions2823]

thanks

[@vaibhavbhise3751]

Really good for beginners

[@saipeddakota78]

Thank you brother very helpful

[@rajeshchandan8116]

Helpful video if any new technican stuck during on-site calibration
Can you share the video of foundation bolt inspection done by paut

[@ndtsolutions2823]

Thank You Rajesh Ji
Hope you are doing good.
We have noted your request on foundation bolt inspection. Within a weak it will be uploaded.

[@arun_pal_8242]

Thanks a lot for uploading helpful videos. 🙏

[@ivoconsulting]

Thanks so very educative

[@badreenathmunnaluri7019]

Nice video, now I understand about calibration
Thank you bro

[@biprodashmandal3150]

Excellent video

[@mdshafaiz207]

Good for very beginner
Overall nice video

[@saddamhussainz1487]

Great

[@shalumall1210]

👌👌

[@arun_pal_8242]

Nice video

[@Its_YJ]

thanks a lot sir

[@meenatiwari9441]

Very nice Supar

[@mushrufsardar6717]

Nice

[@Manojkumar-bw6ob]

Sir, thank you ....your video is very useful to us...plz make more videos

[@ndtsolutions2823]

please let me know the specific topic.

[@prudhvikumard7542]

Sir it's very good session for beginners and we are expecting what is the purpose of TCG , wedge delay selection of probe etc.. in another video's And Thanks for the Video

[@meenatiwari9441]

👌👌👌😍

[@tuskthiru2931]

Nice and superb.
Please share TOFD setup and calibration.

[@ndtsolutions2823]

WILL DO SHORTLY

[@mohdhaziq8333]

maybe for upcoming videos you can upgrade the microphone for good and clear voice performance sir...thanks...anyway very good tutorial..proud of you...

[@arun_pal_8242]

Please more and more videos upload

[@yasararafath2692]

Please share PAUT scan plan video sir

[@husseinalwan3028]

ask about , ERVW blocks (small, medium, and large block) , is coverd the piping diameter range from 3 inch to 20 inch and can we used these blocks for wedge delay and velocity calibration ??

[@ndtsolutions2823]

Hi Hussein Off course we can do the wedge delay and velocity calibration with ERVW block. If you can do TCG rest also can be done

[@HassanHassan-qp6pn]

Hi..
Thanks for your video.
Why you are making threshold very low. Will be getting more noise signals
It is 20 threshold I think good.

[@AkashSharma-do7ov]

🙏🙏🙏🙏🙏

[@dots5501]

plz make the video for TOFD

[@ndtsolutions2823]

Your request is noted. We will make ASAP.

[@dots5501]

@@ndtsolutions2823 thanks for response

[@ArunSingh-fy2jt]

Dear sir I'm looking for PAUT course can't you help to me

[@ivoconsulting]

Nice one give me encoder calibration

[@AkashSharma-do7ov]

Sir please hindi me bhi samja do

[@ndtsolutions2823]

Hello akash it will be difficult. but if you have any doubt in any particular segment i will try to explain you in personal. You can contact me any time

[@deepakrawat3216]

Only time pass not clear introduction

[@ndtsolutions2823]

Deepak thank you for your reply, you may please let know what else can be added

[@rajraj-vl7ct]

Rawat its good for begginers ..don't watch the RUclips for time pass..

[@yashgamers9608]

Why you guys not covering entire weld in PA1 see on land area in PA1 some more position is balance

[@mangeram2731]

Great

[@user-zb4gp4ls6x]

Nice video

[@ganeshvasupalli4658]

Nice video